Watchguard WGAP864SMS Service-Handbuch

Inhaltsverzeichnis

Andere Watchguard Sicherheitssystem Handbücher

Watchguard

Watchguard WGAP864 Bedienungsanleitung

Watchguard

Watchguard DVR4EONPACK Bedienungsanleitung

Watchguard

Watchguard ALC-CAM2 Bedienungsanleitung

Watchguard

Watchguard 2BWIR Bedienungsanleitung

Watchguard

Watchguard Firebox T30 Montageanleitung

Watchguard

Watchguard DVR4ENTPACK3 Bedienungsanleitung

Watchguard

Watchguard N517Series II Bedienungsanleitung

Watchguard

Watchguard ALL-SIR2 Bedienungsanleitung

Watchguard

Watchguard DVR4ENTPACK2 Bedienungsanleitung

Watchguard

Watchguard WGSIR-900 Bedienungsanleitung

Watchguard

Watchguard SMS 2010 WGSMS2010 Bedienungsanleitung

Watchguard

Watchguard NVR4ENT(PACK)2 Bedienungsanleitung

Watchguard

Watchguard DVR4E(PACK) Bedienungsanleitung

Watchguard

Watchguard DVR4ENTPACK4 Bedienungsanleitung

Watchguard

Watchguard Firebox T35-R Montageanleitung

Watchguard

Watchguard NVR4ENTPACK v1.2 Bedienungsanleitung

Watchguard

Watchguard DVR4ENTPACK Bedienungsanleitung

Watchguard

Watchguard DVR4ENTPACK7 Bedienungsanleitung

Watchguard

Watchguard CVRxE Bedienungsanleitung

Watchguard

Watchguard DVR8E(PACK) Bedienungsanleitung

Watchguard

Watchguard WGAP864 Bedienungsanleitung

Watchguard

Watchguard WGWMSA Bedienungsanleitung

Watchguard

Watchguard Firebox III 700 Montageanleitung

Watchguard

Watchguard WGSMSC Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

Technical Bulletin

WGAP864SMS Quick Start Guide

Thursday, 12 November 2015

Tech Bulletin - WGAP864SMS Quick start guide 1.3.docx

Page -1

This quick start guide provides basic setup information only for the Master Phone, testing

and configuration. Please refer to the manufacturer’s manuals for complete configuration

and user information. The quick start guide is not intended to replace the installer manual

and should be used in conjunction with the installer manual.

System requirements:

1. A SIM card is required for the WGAP864SMS module to function:

a. Either prepaid or contract with SMS function enabled, Data is not required,

b. Make sure SIM is not locked. Insert SIM into a phone and unlock SIM if required,

c. Prepaid SIM should be one that does not expire and only needs to be topped up

every 12 months.

2. Check Alarm Panel firmware version.

a. From the Keypad:

i. Press and Hold [*] till KP beeps,

ii. Press [*] again to reveal firmware version,

b. The version must be 2.34 or later to proceed. It he firmware is 2.11 or earlier then

the panel will need a firmware upgrade. Contact RhinoCo Technical Support for

assistance if you need help with firmware upgrade.

Panel Configuration:

1. Fit Jumper (short) to J1 –this is required to set the serial port to the SMS module.

2. Enter Installer Mode [#] [#] [#] [#] * where #### is the installer code. See Installer manual on

how to enter programming mode.

3. Go to Location 196 [1] [9] [6] * If location 196 is not present then the firmware is not 2.34 or

later and will need to be updated.

4. Enter a 6 digit code: [#] [#] [#] [#] [#] [#] *This can be any code you like, its sole purpose is to

bind the WGAP864SMS module to alarm panel.

5. Enter an Account Code for Partition/s that are to be used –P1 = Location 61, P2 = Location

62 etc. [#] [#] [#] [#] *this is required even if the alarm is not monitored. If panel is not

monitored any 4 digit number will suffice.

SMS Commands to WGAP864SMS:

1. Commands are NOT case sensitive and are separated with a SPACE.

2. Users Codes must be pre existing in WGAP864 alarm.

3. The first phone to communicate with the system will become the primary master.

4. Add Master Number –[Master Code] WGAP864 master code

a. [Master Code] space [Add] space [Master] space [Master Phone Number] See

“Adding phone numbers” in the installer manual.

b. Note: the Phone number under Data heading in the table, see “Adding phone

numbers” in the installer manual refers to the mobile number of the phone except

for Time Command in which case it is the number of the SIM in the WGAP864SMS

module.

Technical Bulletin

WGAP864SMS Quick Start Guide

Thursday, 12 November 2015

Tech Bulletin - WGAP864SMS Quick start guide 1.3.docx

Page -2

If you have completed the above steps correctly you should be able to Arm, Trigger an alarm event,

and control outputs.

Follow the installer Manual and User manual for complete configuration options.

Technical Bulletin

WGAP864SMS Quick Start Guide

Thursday, 12 November 2015

Tech Bulletin - WGAP864SMS Quick start guide 1.3.docx

Page -3

Customer may like to try using a GSM app downloaded from Play Store.

GSM Trinket for Android is shown here as an example. Simply program buttons with desired

function to make controlling your alarm a breeze. This app also captures SMSs to and from

the alarm so message code is not visible in your public message box.