WaterCop SmartConnect Bedienungsanleitung
The smart way to get
remote mobile control and access
to your WaterCop automatic
shut-o system.
WIFI
COMPATIBLE
DIRECT
ETHERNET
NOTIFICATION
ALERTS
MOBILE
APPS
REMOTE WATER
CONTROL
System Description
The WaterCop® SmartConnect is designed to work alongside a WaterCop® System to
deliver real time notifications of leaks in your plumbing system and remotely control the
WaterCop valve to shut o the water supply using an app on your smartphone or tablet.
The SmartConnect unit is powered by the WaterCop AUX I/0 port through a CAT5 or
CAT6 cable. The SmartConnect can be connected with up to 50' CAT5 or CAT6.
NOTE: WaterCop systems WCACT1, WPMS, WPMSH, WCNM and WCNM2 units will
need an external power supply, ACA100 (sold separately).
Included in this box:
•WaterCop SmartConnect device
• Wall mount fasteners/anchors
• Interconnect cable
• Owner’s Manual
Read Instructions before any installation is attempted. All sections of this manual
should be read and completely understood.
How the System Works
The SmartConnect unit receives the valve status from the WaterCop AUX I/0 output.
The information goes to a cloud server and out to the SmartConnect App on your
smartphone or tablet. If a leak is detected, the SmartConnect App notifies you of the
potential issue. You can also open and close your WaterCop valve through the app for
complete control of your water supply. The app will also notify you if there’s a signal
loss from the SmartConnect to the cloud service which may indicate a loss of power
or a loss of Internet connection.
SmartConnect
OR
System Requirements
•Smart Phone or tablet with the following:
°Android Version 5.0 or higher/ iOS –
10.3 or higher
°SIM card or Wi-Fi connectivity
•2.4 GHz Router with Protected Wi-Fi
(with 19 character or less password)
•Bluetooth 4.1 or above
•WCACT1, WPMS, WPMSH, WCNM and
WCNM2 require additional power supply,
ACA100 (sold separately)
System and Account Setup
NOTE: Before setup on the WaterCop SmartConnect, verify whether the device will
be connected to the Internet via wireless or Ethernet cable. If using wireless, verify
signal strength before choosing the location of the SmartConnect device. When
running cable from the actuator or control panel to the SmartConnect, use CAT5 or
CAT6, and keep the maximum cable length 50' or less. If more than 50' is required
to get a good signal, the additional power supply (ACA100) can be used. Use the
supplied short cable if signal is adequate.
Setup:
1. Remove WaterCop SmartConnect from box.
2. Mount WaterCop SmartConnect with the supplied wall anchors or other methods
to suit the location.
3. Once mounted, run a CAT5 or CAT6 cable from the WaterCop to the WaterCop
SmartConnect port marked “CONNECT TO VALVE ACTUATOR”. Power is supplied
through the CAT5 or CAT6 cable. If installed on a WCACT1, WPMS, WPMSH,
WCNM and WCNM2, the optional power supply, ACA100 (sold separately), is
required to power the SmartConnect.
4. Download the WaterCop SmartConnect App from the Google Play Store on your
Android device or from the App Store on your iOS device. Make sure Bluetooth
and Location Services are turned on prior to set up and have adequate cellular or
Wi-Fi connection.
5. Open the WaterCop SmartConnect App from your smart device and click on
“Create account”.
6. Enter all information and click “Create”.
7. Open the WaterCop SmartConnect App and join the Wi-Fi network you want the
SmartConnect to operate on. It will populate in the App during setup.
8. Open the WaterCop SmartConntect App and login, if not still logged in.
9. On the My WaterCop Devices screen, click the blue “Add” button in the top right
corner while physically near the WaterCop SmartConnect. After the device pops up,
verify the MAC address matches with the label on the device, click the box to select it.
10. Enter the Unit ID from the carton or WaterCop SmartConnect.
11. The network name will be populated on the next line. Enter the network password
if using Wi-Fi or click the box for Ethernet if the SmartConnect will be hooked
directly to the router.
12. Click “ADD DEVICE”.
13. Click on the displayed device to complete setup.
14. Click the Settings icon at the top right of the screen.
15. Change the SmartConnect name for quick identification on the app.
16. Enter the address on the Location line then click “SAVE”.
Setup Contacts and Testing Notifications
1. Click on the device to access.
2. Click on the human icon near the setting icon.
3. Click “ADD CONTACT”.
4. Enter the information for desired notification then click “SAVE”.
5. Click “ADD” to enter more.
Update Wi-Fi Password After Initial Setup
1. Click on the device to access.
2. Click on the Settings icon.
3. Click “ADVANCED SETTINGS”.
4. Select “WI-FI SETTINGS”.
5. Enter new credentials and click “SAVE”.
Reset to Factory Settings
1. Click on the device to access.
2. Click on the Settings icon.
3. Click “ADVANCED SETTINGS”.
4. Click “RESET TO FACTORY SETTINGS”.
This is the same as “FORGET NETWORK” so this will reset the SmartConnect and
forget the wireless network password you entered previously.
INSTALLER NOTE: If the contact persons aren’t on-site to confirm notification receipt,
add your contact information to test then delete when testing is complete.
Troubleshooting
Problem Solutions
Cannot see or
connect to device at
“Add” screen
Turn o your mobile device’s Bluetooth feature for a
few seconds and then turn it back on again to see if
the SmartConnect’s connection is restored.
Remove the CAT5 cable or power supply from
the SmartConnect and reconnect to cycle power.
No connection, buttons
gray after configuring
Wi-Fi network
Verify network name and password are correct,
app will not notify of incorrect name or password.
Loss of power or network connection to the
WaterCop SmartConnect, check system to verify
Wi-Fi connection and power to the WaterCop
SmartConnect.
Valve “CONNECTION
LOST” message
While adding and setting up device, if 30 seconds
pass before connecting to a network, it will send
the “CONNECTION LOST” message.
Once connected to a network, the message can be
deleted and won’t return unless there’s a power or
Internet outage.
Loss of power or network connection to the
WaterCop system, check system to verify Wi-Fi
connection and power to the WaterCop
SmartConnect.
Get “Internet error valve
did not change state”
message
Ensure Wi-Fi password 19 characters or less.
If you are unable to resolve any of the troubles noted above or experiencing other
issues, please contact your Installer directly or WaterCop Customer Service for
assistance at 800-545-3636.
192616
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiver.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
•Consult the dealer for help.
The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this equipment.
Operation is subject to the following two conditions:
1. This device may not cause interference
2. This device must accept any interference, including interference that may cause
undesired operation of the device
Visit WaterCop.com for your warranty information.
Inhaltsverzeichnis
Andere WaterCop Controller Handbücher
