Waterford 75cm Handbuch

75cm GAS HOB

OPERA

OPERATING & INST

TING & INSTALLA

ALLATION MANUAL

TION MANUAL

Please read these instructions carefully before use

Please read these instructions carefully before use.

Page No.

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2. Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3. Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

4. Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

5. Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

6. Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Positioning & Fitting The Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

7. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

8. Converting For LPG Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

9. Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

10. Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

11. Hob Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

12. Using The Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

13. Using The Dual Burner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

14. Choosing The Right Burner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

15. Additional Pan Supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

16. Wok Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

17. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

18. Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

19. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

TABLE OF CONTENTS

INTRODUCTION

Dear Customer,

Thank you for buying a Waterford Appliance.

The quality of Waterford’s appliances is exceptional and immediately visible. Each one is designed to with-

stand the most demanding kitchen environment. But its not just about sleek contemporary looks; every detail

reflects Waterford Stanley’s long-standing design for total performance ethos. That is why our ovens are easy

to clean, our hobs are powerful, our extractor hoods efficient and our refrigerators designed for optimum stor-

age. All Waterford products are made from quality stainless steel for durability.

We would advise you to take time out and read your instruction manual before using your Waterford

Appliance. This will ensure that you use all technical features your Waterford Appliance has to offer.

Waterford Stanley make every effort to ensure that our products meet all your requirements, and our

Customer Relations department is at your disposal, to answer all your questions. In the unlikely event of a

fault, look here for information on how to rectify minor faults.

To ensure your warranty is validated, please complete the attached warranty card and return to Waterford

Stanley.

Enjoy your Waterford Appliance

Note: Before using the gas hob for the first time, read the operating manual carefully so that you can ensure

safe operation and avoid damage to the hob.

* The hob should only be used when it has been fully installed as outlined in the Installation Section.

* Any repairs to this appliance must be carried by an approved Waterford Service Engineer. Unprofessional

repairs may compromise the safety of the appliance.

* Do not allow children to come near the hob when in operation, as they might move the hot pots and get

burned.

* Do not leave the plate unattended when cooking using fats and oils as they may create a fire hazard.

* This appliance should be cleaned on a regular basis in order to maintain its efficient operation.

* This appliance is designed for domestic use only.

* After unpacking, please dispose of the packing materials in a suitable manner. All materials used for pack-

ing are harmless to the environment, can be recycled and are marked with the relevant symbol.

This electrical appliance has components classified as WEEE (Electrical & Electronic Equipment Waste)

requiring selective treatment for correct ecological disposal. WEEE includes: condensers, switches, printed

circuits, electrical cables.

THIS ELECTRICAL APPLIANCE MUST NOT BE DISPOSED OF IN MIXED URBAN WASTE BUT MUST

BE SENT TO SEPARATE COLLECTION:

The purpose of Directive 2002/96/EC for differentiated treatment of WEEE are in particular;

protecting, safeguarding & improving the environment, the protection of human health and

the expedient and rational use of natural resources.

When new appliance is supplied, the distributor undertakes to collect this electrical appliance

and have it sent to authorised treatment centres for the disposal of WEEE.

The producer of this electrical appliance meets the requirements of Directive 2002/96/EC by

promoting and supporting the recovery, reuse and recycling of WEEE.

SAFETY INSTRUCTIONS

PRODUCT FEATURES

CONTROL PANEL

75cm Built-In Gas Hob with front commands:-

1. Auxiliary Burner (A)

2. Semi-Rapid back burner (SR)

3. Rapid Burner (R)

4. Semi-Rapid Front Burner (SR)

5. Dual Burner

Fig.1

Outer wok

burner

control knob

Inner wok

burner

control knob

Front left

burner

control knob

Back left

burner

control knob

Back right

burner

control knob

Front right

burner

control knob

Fig.2

TECHNICAL INFORMATION

Voltage : 230V ~ 50 Hz

Max Burner Power: 11.8 kW

Max Electrical Power: 0.6kW

Dimensions: 750mm x 500mm x 50mm

Gas Burner Technical Data

GAS TYPE G20 (NAT GAS)

GAS PRESSURE 20 mbar

Burners Power Inputs

Max (kW)

Power Inputs

Min (kW)

O Injectors

A 1.00 0.30 0.72

SR 1.75 0.44 0.97

R 3.00 0.75 1.15

Dual 4.30 0.30

Inner

0.66

Outer

1.00

G30/31 (LPG)

37 mbar

O Injectors

0.50

0.65

0.85

Inner Outer

0.46 0.64

INSTALLATION INSTRUCTIONS

The appliance must be installed in accordance with

the regulations in force. All installation and adjust-

ment operations must be carried out by a suitable

qualified person.

The manufacturer declines all liability for any direct

or indirect damage if these regulations are not com-

plied with.

Pre-Installation

Prior to installing the product, all packaging should

be removed from the appliance and any residues

removed using soapy warm water. The appliance

should then be checked and any apparent defects

reported to the Waterford Stanley Service

Department (051-302333 for ROI or 028-87722193

for Northern Ireland).

Before selecting a position to install the hob, the fol-

lowing must be considered:

* The hob should only be fitted on a heat resistant

(minimum temperature 90oC) worktop.

* When installing the electrical supply or gas sup-

ply to the hob, ensure that they do not touch any

hot parts of the hob or other units around it.

* If the hob is fitted without an oven directly below

it, a separation panel must be fitted under the

hob base at a distance of at least 10mm.

* If the hob is fitted with an oven directly below, a

divider panel must be fitted under the hob at a

distance of 15mm and the aeration clearance

around the oven should be adhered to, as shown

in Fig.3.

Fig.4

Fig.3

Positioning & Fitting The Hob

1. Cut out a square opening in the worktop, as

shown in Fig.4, with a minimum of 120mm of the

worktop behind the opening.

2. Place the sealing gasket supplied along the out

side edge of the cut-out in the worktop.

3. Position the hob in the cut-out space making

sure it is centred.

4. Attach the hob to the worktop with the fixing

brackets as shown in Fig.5.

GAS CONNECTION

Fig.5

Note: This hob is configured for Natural Gas as

standard. It is the installers responsibility to

make the necessary modifications (as out-

lined in the section “converting for LPG

use”) to ensure the appliance is correctly

configured for use with LPG.

The hob should be connected using a O12mm

metal hose that complies with the National

Regulations with the connection made to the gas

connection (on the underside towards the back

edge of the hob) using an appropriate seal between

the pipe and the hose. The hose must never be

more than 1.5 metres long.

Note: A complete set of LPG injectors are supplied

with the hob. The injectors are identified by

their diameter which is printed on each

injector.

1. Shut off the electrical and gas supply to the hob.

2. Replace the burner injectors by removing the

burner flame cap cover, the burner cap and

unscrewing the injector using a suitable spanner

(see Fig.6).

3. Reinstate the electrical gas supplies. Regulate

the low flame setting for each burner using the

following procedure.

a. Ignite the burner and leave it in operation on

the high flame setting for one minute.

b. Turn the knob to the low flame setting.

c. Remove the knob by pulling it off the tap

shaft.

d. Insert a No.2 flat head screwdriver into the `

centre of the gas valve shaft and turn it

clockwise to decrease the flame & anticlock-

wise to increase the flame. (See fig.6).

Replace the knob onto the tap shaft.

CONVERTING FOR LPG USE

Fig 6

ELECTRICAL CONNECTION

Note: When carrying out any work on this appli-

ance the electrical supply to it must be isolated.

This appliance requires a 230V, 50Hz A.C. supply

and the electrical installation must be carried out by

a qualified electrician in compliance with the current

regulations.

The hob must be connected to a 16amp cooker box

control unit using an adequately sized power cable.

The power lead must not reach a temperature in

excess of 50oC.

Fig. 7

VENTILATION

The room where the gas hob is installed must be

well ventilated to allow proper gas combustion.

The air flow necessary must be no less than 2m3/h

for each kW of the appliance’s maximum rated

power. The minimum air flow requirement for the

hob should therefore be 23.6m3/h (maximum power

rating being 11.8 kW).

When fitting an extraction hood over the appliance

ensure that there is a permanent air vent to the

room that allows adequate ventilation for both the

hob and the hood.

If the extraction hood is installed above the hob, a

minimum distance of 750mm must be maintained

between the top surface of the appliance and the

bottom surface of the hood. See Fig.8

Fig. 8

HOB OPERATION

Fig. 9

Using The Rings

Press the corresponding gas ring knob (refer to

control panel layout) and turn it to the maximum

setting. The burner will spark and ignite. Keep the

knob pressed in for approximately 15 seconds, if

the burner fails to ignite or it extinguishes wait at

least 1 minute before repeating the lighting proce-

dure. Once the burner has remained lighting, the

control knob can be adjusted to the required setting

(see Fig.9)

Valve closed, no gas flow.

Maximum capacity, maximum gas flow.

Minimum capacity, minimum gas flow.

CHOOSING THE RIGHT BURNER

Using The Dual Burner

The dual burner is controlled by two gas ring knobs

(refer to the control panel layout). The inner ring

knob allows for the burner to be used as an auxil-

iary burner which is suitable for pot diameters rang-

ing from 60-140mm. By turning on both the inner

and outer ring knobs, the burner is used with pot

diameters ranging from 240-260mm. The dual

burner ring knobs are operated as outlined in the

“Using The Rings” section.

The symbol printed to the left of each knob indi-

cates the corresponding burner. (see diagram of

control panel on page 4). Choosing the most

appropriate burner depends on the pan diameter.

See table below:

For best efficiency it is important that the right burn-

er is chosen for each pan.

PAN DIAMETER

BURNER MINIMUM

DIAMETER

MAXIMUM

DIAMETER

Auxiliary 60mm

(with reduction)

140mm

Semi Rapid 160mm 200mm

Rapid 200mm 240mm

Dual 240mm 260mm

ADDITIONAL PAN SUPPORTS

Support reduction for pans:

This support should only be used with the auxiliary

burner and is used for pans with a diameter of

60mm to prevent tipping. See Fig.10.

Fig. 10

This optional support was designed for concave

base pans and are ideal for woks. See Fig 11.

WOK SUPPORT

Fig 11

In order to maintain the appearance of this hob,

periodical cleaning is recommended. Wipe away

any spills when they occur in order to prevent

burned on deposits which can be difficult to remove.

A. Stainless Steel Surface

Use hot water and soap or non-chlorate deter-

gent, applied with a soft cloth to remove most

soiling and polish dry to avoid streaking. For

stubborn stains we recognised stainless steel

cleaner, such as Waterford Chrome Cleaner (ask

you local dealer for more information) or stain-

less steel soft wool.

B. Gas Rings

* The hob burner cap and burner flame cap covers

(see Fig.12) can be washed with a damp cloth

and soapy water.

* The hob burner caps can turn bluish around the

burner area due to the heat. Steel wool can be

used to decrease this effect.

* Gently wipe clean the electric ignition “E” and

thermocouple “T” (see Fig.12) with a dry cloth.

* Replace burner caps and burner flame cap

covers taking care not to damage the electric

ignition and thermocouple.

* In order to avoid damage to the electric ignition,

avoid using the rings when the burner caps and

flame cap covers are not in place.

CLEANING

Fig 12

TROUBLE SHOOTING

The following are a list of minor faults (with instructions on how to rectify them) that should be used by the

operator in the event of the appliance not working prior to contacting a Service Engineer.

PROBLEM CAUSE ACTION

1. None of the rings lighting - power supply failure

- gas supply turned off

- check the in-house electric sys-

tem fuse, replace if necessary

- check position of gas shut off

valve to appliance.

2. One of the rings won’t light - dirt on ignitor

- injector blocked

- burner cap & flame cap cover not

in position

- clean hob ring ignitor

- remove burner cap & flame cap

cover. Remove obstruction from

injector (see Fig.12)

- Re-position

3. Hob ring won’t stay lighting - dirt on thermocouple - clean thermocouple

Inhaltsverzeichnis

Andere Waterford Kochfeld Handbücher

Waterford

Waterford Ceramic Hob Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Siemens

Siemens EX875KYV1E Technisches Datenblatt

AEG

AEG CERAMIC HOB 6010 K Bedienungsanleitung

VALERA

VALERA CT 70A Bedienungsanleitung

Zanussi

Zanussi ZGF 6420 Bedienungsanleitung

Gaggenau

Gaggenau CI 273 Bedienungsanleitung

G3 Ferrari

G3 Ferrari Energy Bedienungsanleitung

Pkm

Pkm IN4B Bedienungsanleitung

Award

Award H903BG Bedienungsanleitung

Zanussi

Zanussi VCH 5005 RZ Bedienungsanleitung

Miele

Miele KM 523 Bedienungsanleitung

Hotpoint

Hotpoint IS67V8CCXT/E Bedienungsanleitung

AEG

AEG HK854870XB Bedienungsanleitung

Cookology

Cookology SEP600BK Bedienungsanleitung

Bauknecht

Bauknecht Hob Bedienungsanleitung

Zanussi

Zanussi ZGM 782 Bedienungsanleitung

dipo INDUCTION

dipo INDUCTION DIBK218S Bedienungsanleitung

Miele

Miele KM 5987 Bedienungsanleitung

Miele

Miele KM 360 G Bedienungsanleitung