Waters E-SAT/IN Bedienungsanleitung

Waters e-SAT/IN Module

Installation Guide

71500049404/Revision C

DOCUMENT OR PARTS THEREOF MAY NOT BE REPRODUCED IN ANY

FORM WITHOUT THE WRITTEN PERMISSION OF THE PUBLISHER.

The information in this document is subject to change without notice and

should not be construed as a commitment by Waters Corporation. Waters

Corporation assumes no responsibility for any errors that may appear in this

document. This document is believed to be complete and accurate at the time

of publication. In no event shall Waters Corporation be liable for incidental or

consequential damages in connection with, or arising from, its use.

Trademarks

Waters is a registered trademark of Waters Corporation, and e-SAT/IN,

Empower, SAT/IN and “THE SCIENCE OF WHAT’S POSSIBLE.” are

trademarks of Waters Corporation.

Other registered trademarks or trademarks are the sole property of their

owners.

iii

Customer comments

Waters’ Technical Communications department invites you to tell us of any

errors you encounter in this document or to suggest ideas for otherwise

improving it. Please help us better understand what you expect from our

documentation so that we can continuously improve its accuracy and

usability.

We seriously consider every customer comment we receive. You can reach us

at [email protected].

Contacting Waters

Contact Waters®with enhancement requests or technical questions regarding

the use, transportation, removal, or disposal of any Waters product. You can

reach us via the Internet, telephone, or conventional mail.

Safety considerations

Some reagents and samples used with Waters instruments and devices can

pose chemical, biological, and radiological hazards. You must know the

potentially hazardous effects of all substances you work with. Always follow

Waters contact information

Contacting medium Information

Internet The Waters Web site includes contact

information for Waters locations worldwide.

Visit www.waters.com.

Telephone and fax From the USA or Canada, phone 800

252-HPLC, or fax 508 872 1990.

For other locations worldwide, phone and fax

numbers appear in the Waters Web site.

Conventional mail Waters Corporation

34 Maple Street

Milford, MA 01757

USA

Good Laboratory Practice, and consult your organization’s safety

representative for guidance.

Safety advisories

Consult Appendix A for a comprehensive list of warning and caution

advisories.

Operating this instrument

When operating this instrument, follow standard quality-control (QC)

procedures and the guidelines presented in this section.

Applicable symbols

Audience and purpose

This document describes the installation of the e-SAT/IN module. It is

intended is intended to be used by qualified operators, installation engineers,

and field service engineers.

Symbol Definition

Manufacturer

Authorized representative of the European

Community

Confirms that a manufactured product complies

with all applicable European Community

directives

Australia C-Tick EMC Compliant

Confirms that a manufactured product complies

with all applicable United States and Canadian

safety requirements

Consult instructions for use

Intended use of the Waters e-SAT/IN module

Waters designed the e-SAT/IN module to translate analog signals to digital

signals for data collection. You can operate the device with instruments used

to analyze various types of compounds. The e-SAT/IN module is for research

use only.

Calibrating

To calibrate LC systems, follow acceptable calibration methods using at least

five standards to generate a standard curve. The concentration range for

standards should include the entire range of QC samples, typical specimens,

and atypical specimens.

When calibrating mass spectrometers, consult the calibration section of the

operator’s guide for the instrument you are calibrating. In cases where an

overview and maintenance guide, not operator’s guide, accompanies the

instrument, consult the instrument’s online Help system for calibration

instructions.

Quality-control

Routinely run three QC samples that represent subnormal, normal, and

above-normal levels of a compound. Ensure that QC sample results fall within

an acceptable range, and evaluate precision from day to day and run to run.

Data collected when QC samples are out of range might not be valid. Do not

report these data until you are certain that the instrument performs

satisfactorily.

ISM classification

ISM Classification: ISM Group 1 Class B

This classification has been assigned in accordance with CISPR 11 Industrial

Scientific and Medical (ISM) instruments requirements. Group 1 products

apply to intentionally generated and/or used conductively coupled

radio-frequency energy that is necessary for the internal functioning of the

equipment. Class B products are suitable for use in both commercial and

residential locations and can be directly connected to a low voltage,

power-supply network.

EC authorized representative

Waters Corporation

Stamford Avenue

Altrincham Road

Wilmslow SK9 4AX UK

Telephone: +44-161-946-2400

Fax: +44-161-946-2480

Contact: Quality manager

Table of Contents vii

Trademarks ............................................................................................................ ii

Customer comments ............................................................................................ iii

Contacting Waters ............................................................................................... iii

Safety considerations .......................................................................................... iii

Safety advisories................................................................................................. iv

Operating this instrument ................................................................................. iv

Applicable symbols ............................................................................................. iv

Audience and purpose......................................................................................... iv

Intended use of the Waters e-SAT/IN module.................................................... v

Calibrating ........................................................................................................... v

Quality-control ..................................................................................................... v

ISM classification .................................................................................................. v

ISM Classification: ISM Group 1 Class B .......................................................... v

EC authorized representative ........................................................................... vi

1 Introduction ............................................................................................ 1-1

About the e-SAT/IN module ............................................................................ 1-2

Features .............................................................................................................. 1-3

Baseline noise .................................................................................................. 1-3

Sampling rates ................................................................................................. 1-3

Ethernet I/O connection .................................................................................. 1-4

Analog to digital conversion ............................................................................ 1-4

BCD input ........................................................................................................ 1-5

Programmable event outputs.......................................................................... 1-6

Power-on self-tests........................................................................................... 1-6

IP address sequence......................................................................................... 1-6

External power supply..................................................................................... 1-7

Table of Contents

viii Table of Contents

2 Installing the Module ............................................................................ 2-1

Selecting the site ............................................................................................... 2-2

Making electrical connections ....................................................................... 2-2

Installing the network interface card .......................................................... 2-2

Ethernet connections ....................................................................................... 2-3

Single e-SAT/IN module connection ............................................................... 2-3

Multiple e-SAT/IN connections ....................................................................... 2-4

Network installation guidelines...................................................................... 2-4

Integrating an e-SAT/IN module to an existing busSAT/IN system............. 2-6

Connecting analog cables ............................................................................... 2-7

Connecting event cables .................................................................................. 2-8

Event in connections........................................................................................ 2-8

Event out connections...................................................................................... 2-8

Event in and out signal assignments.............................................................. 2-8

Connecting the BCD cable ............................................................................ 2-10

Connecting the power supply ...................................................................... 2-11

3 Using the e-SAT/IN Module .................................................................. 3-1

Powering on the module ................................................................................. 3-2

e-SAT/IN module self-tests.............................................................................. 3-2

Configuring the e-SAT/IN module ................................................................. 3-3

Creating a chromatography system................................................................ 3-3

Configuring Empower software for the e-SAT/IN module............................. 3-3

Smoothing noise in Empower........................................................................ 3-15

Troubleshooting .............................................................................................. 3-17

Power-on problems......................................................................................... 3-18

System troubleshooting ................................................................................. 3-18

When to call Waters technical service .......................................................... 3-19

Error messages .............................................................................................. 3-20

A Safety Advisories .................................................................................. A-1

Table of Contents ix

Warning symbols ............................................................................................... A-2

Task-specific hazard warnings........................................................................ A-2

Specific warnings ............................................................................................. A-3

Caution symbol .................................................................................................. A-5

Warnings that apply to all Waters instruments ......................................... A-6

Electrical and handling symbols ................................................................. A-11

Electrical symbols .......................................................................................... A-11

Handling symbols .......................................................................................... A-12

B Specifications ........................................................................................ B-1

C Spare Parts ............................................................................................ C-1

Index ..................................................................................................... Index-1

x Table of Contents

Inhaltsverzeichnis

Andere Waters Steuereinheit Handbücher

Waters

Waters 2545 Binary Gradient Module Handbuch

Waters

Waters Alliance e2695 Handbuch

Waters

Waters Pump Control Module II Bedienungsanleitung

Waters

Waters 2690 Bedienungsanleitung

Waters

Waters 61164 Bedienungsanleitung

Waters

Waters Alliance e2695 Handbuch

Waters

Waters Bus SAT/IN Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

Waters e-SAT/IN Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken