Waterway Power Defender 140 Bedienungsanleitung

Installation and Operation Manual

Model: Power Defender 140 for Waterway

Programmable Pool Pump Motor/Control

This product does NOT provide a Safety

Vacuum Release System (SVRS).

Save this instruction manual for future reference.

Part #: M018316850000, Rev B Rev Date: February 21, 2020

Table of Contents

Important Safety Information .......................................................................................................... 1

Power Defender 140 for Waterway ................................................................................................. 3

Features................................................................................................................................. 3

Dimensions (Square Flange).................................................................................................. 4

Dimensions (Thru Bolt with Base) .......................................................................................... 5

Electrical Requirements .................................................................................................................. 6

Input....................................................................................................................................... 6

Rated Output.......................................................................................................................... 6

Agency.............................................................................................................................................. 7

Safety..................................................................................................................................... 7

Electromagnetic Compatibility (EMC) ..................................................................................... 7

Installation Instructions................................................................................................................... 8

Protect against Heat............................................................................................................... 8

Protect against Dirt................................................................................................................. 8

Protect against Moisture......................................................................................................... 8

Preparing the Motor for Operation .......................................................................................... 8

Wiring the Motor..................................................................................................................... 9

Motor Protections .......................................................................................................................... 11

Low Temperature Monitor .................................................................................................... 11

Motor Stalled ........................................................................................................................ 11

Open Output Phase.............................................................................................................. 11

Output Over Current............................................................................................................. 11

Output Over Power............................................................................................................... 11

Power Module Temperature ................................................................................................. 11

Under Voltage ...................................................................................................................... 11

Hardware Protection............................................................................................................. 12

Mechanical Requirements .................................................................................................... 12

Environmental Requirements ............................................................................................... 12

Pump Control via the User Interface ............................................................................................ 13

Navigation Overview ............................................................................................................ 13

Configure Your Pool Pump Motor......................................................................................... 19

Overriding a Timer................................................................................................................ 23

Wiring a Remote Connection................................................................................................ 24

Troubleshooting ............................................................................................................................ 25

Basic Troubleshooting.......................................................................................................... 25

General Troubleshooting ...................................................................................................... 26

Fault Conditions ................................................................................................................... 27

Maintenance................................................................................................................................... 30

Lowering Your Utility Costs .................................................................................................. 30

Example Calculations........................................................................................................... 30

Default Settings ............................................................................................................................. 31

Warranty Information..................................................................................................................... 33

P o w e r D e f e n d e r 1 4 0 f o r W a t e r w a y P o o l P u m p M o t o r

I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l 1

Important Safety Information

·Read all instructions thoroughly and be familiar with the equipment before installing or working on it.

·Before connecting or disconnecting cables or other electrical connections, verify that electrical

power to the system is removed. Failure to comply may cause serious damage to the pool pump

motor or injury.

·Because of the risk of electric shock, only individuals thoroughly trained in the use of multimeters

should conduct voltage tests.

·Never touch the metal contacts on the multimeter during a test.

·Always check testing equipment for proper operation before use.

Installation, operation, and maintenance must be performed by qualified personnel. Familiarization with

and adherence to the National Electrical Code (NEC), National Fire Protection Association (NFPA)

standards and to local codes are required. It is important to observe safety precautions to protect

personnel from possible injury. Personnel should be instructed for handling each of the following:

·Only apply nameplate voltage (115 or 230) with the Voltage Selection Switch in the correct position.

·Insulate all connections carefully to prevent grounding or short circuits. Reinstall all conduit and

terminal box covers.

·To avoid overheating or loss of output power, voltage to the motor control unit must be within plus

or minus 10% of the nameplate voltage.

·Make sure the unit is electrically grounded and that proper electrical installation, wiring, and controls

are used consistent with local and national electric codes. Refer to NEC Handbook and NFPA No.

70. Employ qualified electricians for the installation and maintenance of the unit.

·Code requirements differ from state to state. Install equipment using qualified electricians

in accordance with the applicable codes and ordinances in your area and in accordance with NEC.

All electrical connections should be made and maintained by a qualified or licensed electrician.

·Make sure there are no unusual noises or vibrations when the motor is running.

·Avoid contact with energized circuits and rotating parts.

·Provide proper safeguards for personnel against rotating parts.

P o w e r D e f e n d e r 1 4 0 f o r W a t e r w a y P o o l P u m p M o t o r

I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l 2

·Always disconnect electrical power at the fuse box or circuit breaker panel before handling electrical

connections or performing maintenance on this unit. Allow the motor to come to a complete stop

and wait two (2) minutes. This allows the capacitors to discharge any residual voltage.

·All aspects of the installation must conform to the applicable requirements of the NEC, including

Article 430 (Motor Circuits and Controllers), as well as all local codes.

·Double-check to make sure that electrical power is removed and that it cannot be turned on while

you are working on the equipment.

·A poor electrical connection can overheat and cause terminal and/or terminal board failures.

Examine the connections carefully for any signs of physical deterioration or loose fit to the motor

terminal block.

·Care must be taken to assure connections are made to the proper terminals and adequate electrical

clearances are maintained.

·The control unit on the motor contains hazardous voltage.

·Wear safety glasses to inspect the equipment while it is running or while working on equipment.

The motor and control unit are assembled and calibrated as a set. There are no serviceable parts in the

motor or control.

·Do not lift the Power Defender 140 for Waterway motor by the electronic control.

·To prevent permanent damage to the unit, only apply nameplate voltage.

·Do not strike the motor shaft with a hammer or other tool as this may cause damage.

·Voltage symbols vary among different multimeters and may be displayed as Vac, AC, V, or a V

beneath a wavy line. Select the correct symbol and set the multimeter to the voltage closest to but

higher than the voltage you are measuring.

·Although designed for outdoor application, the Power Defender 140 for Waterway Pool Pump Motor

is properly packaged for shipment and storage and should be kept in a clean and dry indoor area

until installed for use.

P o w e r D e f e n d e r 1 4 0 f o r W a t e r w a y P o o l P u m p M o t o r

I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l 3

Power Defender 140 for Waterway

The Power Defender 140 for Waterway variable speed pool pump motor is a premium efficient product

that includes a fully integrated motor, control, and User Interface (UI). The product provides

programming flexibility and speed range capability. It is also designed to communicate and operate with

a variety of external system controls, in addition to the on-board User Interface.

Features

·Total Output Horsepower: 1.40HP, 40° C (1.25HP, 50° C) at 3450 RPM, variable speed

·Voltage/Hertz: Single phase, 115 and 230 Vac, 50 or 60 Hz

·Speed Range: 600-3450 RPM

·Efficiency: 80% at 3450 RPM

·Enclosure: Finned Aluminum enclosure providing a Water Ingress Protection level of IPX5 for long

field life in outdoor environmental conditions

·Frame: Square Flange (NEMA 42Y mounting), Thru Bolt with Base

·User Interface: Fully functional, easy to operate

·Rotation: Counter-clockwise (viewing motor shaft)

·Low Temperature Monitor: Threshold temperature configurable in the UI

·Capable of communicating with specific pool control systems via MODBUS

·Capable of setting up to seven daily schedules

·Adjustable priming time & speed

·Menu keypad lockout

·Designed for quiet operation

·Fully Integrated: Designed for simple “Drop-In” installation with no complex wiring

·UL 1081 approvable

Square Flange Thru Bolt with Base

P o w e r D e f e n d e r 1 4 0 f o r W a t e r w a y P o o l P u m p M o t o r

I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l 4

Dimensions (Square Flange)

All dimensions are for reference only.

Side View

Fan View Shaft View

P o w e r D e f e n d e r 1 4 0 f o r W a t e r w a y P o o l P u m p M o t o r

I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l 5

Dimensions (Thru Bolt with Base)

All dimensions are for reference only.

Side View

Fan View Shaft View

P o w e r D e f e n d e r 1 4 0 f o r W a t e r w a y P o o l P u m p M o t o r

I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l 6

Electrical Requirements

Input

Input Line Voltage

The unit is intended to be operated from a 115 or 230 Vac single phase power supply. The input AC

supply frequency is 50 or 60 Hz nominal. Full rated output power is guaranteed between the Minimum

Full Performance Voltage and the Maximum Operating Voltage. The unit operates with frequency

variations up to +/-10 percent of the nominal value.

Line

Input 1Ø

Minimum

Operating Voltage

Minimum Full

Performance Voltage

Maximum

Operating Voltage

115 Vac

104 Vac

127 Vac

230 Vac

207 Vac

264 Vac

Input Line Current

Full load AC line currents are listed below. The inverter limits the inrush current to less than 150A peak

surge. The duration is less than 5 milliseconds.

AC Input

Full Load Current

115 Vac

15.6 amps

230 Vac

9.5 amps

Input Power Factor

There is no power factor correction circuit on the motor control board. Power factor range is normally

65 to 75%.

Rated Output

The unit is rated for the following maximum outputs:

Speed (RPM)

Rated Torque

1.40HP

3450

25.5 in-lb.

P o w e r D e f e n d e r 1 4 0 f o r W a t e r w a y P o o l P u m p M o t o r

I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l 7

Agency

UL File Number:

·E503587 (control)

·E255002 (motor and control)

Safety

Document

Description

UL 60730-1

Principal standard for the design of an electronically protected motor.

UL 1998

Safety standard for software in programmable components of an

electronically protected motor.

UL1081

(approvable)

Standard for Safety: Swimming Pool Pumps, Filters and

Chlorinators.

UL 1004-1

Standard for Rotating Electrical Machines - General Requirements.

UL 1004-7

Standard for Electronically Protected Motors.

Electromagnetic Compatibility (EMC)

Document

Description

CISPR 22/EN55022

Standards applicable to information technology equipment.

IEC/EN 61000

-4-2

Testing and measurement techniques

- Electrostatic Discharge

Immunity Test

IEC/EN 61000

-4-4

Testing and measurement techniques - Electrical Fast

Transient/Burst Immunity Test.

IEC/EN 61000

-4-5

Testing and measurement techniques

- Surge Immunity Test.

P o w e r D e f e n d e r 1 4 0 f o r W a t e r w a y P o o l P u m p M o t o r

I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l 8

Installation Instructions

Follow these instructions to prolong the life of the pump motor and control. Install the product on a

secure and level platform or base, such as a concrete pad.

Installation, operation, and maintenance must be performed by qualified personnel. Familiarization with

and adherence to the National Electrical Code (NEC), National Fire Protection Association (NFPA)

standards and to local codes are required. It is important to observe safety precautions to protect

personnel from possible injury.

·Code requirements differ from state to state. Install equipment using qualified electricians in

accordance with the applicable codes and ordinances in your area and in accordance with NEC. All

electrical connections should be made and maintained by a qualified or licensed electrician.

Protect against Heat

·Shade the motor / control from the sun.

·Provide ample cross ventilation.

·Protect the motor / control from lint, etc., which can clog the ventilation openings.

Protect against Dirt

·Keep the motor / control and the surrounding area clean.

·Avoid sweeping or stirring dust near the motor / control while it is running.

·Avoid storing or spilling dry chemicals near the motor / control.

Protect against Moisture

·Provide protection from rain, snow, etc.

·Do not wrap the motor / control with plastic or other air tight materials.

·Locate the motor / control on a slight elevation so that water does not run or puddle nearby.

·Avoid splashing water on or near the motor / control.

·Repair leaky pipe joints or pump seals promptly.

Preparing the Motor for Operation

The Power Defender 140 for Waterway has been functionally tested before shipment. Most pool

installations already have the electrical power in conduit. However, on-site installation requirements and

electrical codes vary widely and are the responsibility of the installer. The motor / control must be wired

before operating.

Note: An electrical power cable is not provided.

You will need the following tools.

·1/4-inch socket or nut driver

·Flathead or Phillips screwdriver

Inhaltsverzeichnis

Andere Waterway Schwimmbadpumpe Handbücher

Waterway

Waterway SVL56 Bedienungsanleitung

Beliebte Schwimmbadpumpe Handbücher anderer Marken

TIP

TIP STEAM 35000 INV Verdrahtungsschema

Jacuzzi

Jacuzzi J-HI27C Bedienungsanleitung

PoolRite

PoolRite SQI 400 Bedienungsanleitung

Pentair

Pentair IntelliComm Bedienungsanleitung

Calpeda

Calpeda NMP Bedienungsanleitung

WilTec

WilTec 50374 Bedienungsanleitung

Evolution

Evolution Evoflow Storm Eco-V Bedienungsanleitung

AquaTools

AquaTools AT240701 Bedienungsanleitung

Sibo

Sibo AquaForte RD352 Bedienungsanleitung

CLS

CLS VICTORIA PLUS SILENT Bedienungsanleitung

Pond One

Pond One Piranha 800 Bedienungsanleitung

Hayward

Hayward VSP Bedienungsanleitung

Resol

Resol DeltaSol B Pro Bedienungsanleitung

Evolution Aqua

Evolution Aqua UniTech Perfect 5000 Bedienungsanleitung

Outside Living Industries

Outside Living Industries Ubbink Heatermax Pool Kurzanleitung

CPI

CPI Olympic 2P1815 Bedienungsanleitung

Flotec

Flotec FP6121-01 Bedienungsanleitung

Pentair

Pentair ONGA LEISURETIME LTP400 Bedienungsanleitung