Watts SentryPlus Alert Bedienungsanleitung

IOM-UpGradeKit-SentryPlusAlert2

Installation, Operation, and

Maintenance Manual

SentryPlus™ Alert

Universal Upgrade Kit

WARNING

Read this Manual BEFORE using this equipment.

Failure to read and follow all safety and use information

can result in death, serious personal injury, property

damage, or damage to the equipment.

Keep this Manual for future reference.

Table of Contents

Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Understanding Safety Information. . . . . . . . . . . . . . . . . . . . 2

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

List of Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1. Installing the Flood Sensor (Backflow RPZ Upgrades) . . 3

2. Installing and Wiring/Retrofitting the Control Box . . . . 4-5

3. Installing the Cellular Gateway . . . . . . . . . . . . . . . . . . . . 6

4. Setting Up the Cellular Gateway . . . . . . . . . . . . . . . . . . . 6

5. Registering SentryPlus Alert . . . . . . . . . . . . . . . . . . . . . . 7

Start-up Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Startup Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

NOTICE

Use of the SentryPlus AlertTM technology does not replace

the need to comply with all required instructions, codes,

and regulations related to the installation, operation, and

maintenance of an RPZ backflow preventor, including the

need to provide proper drainage in the event of a discharge.

Watts is not responsible for the failure of alerts due to

connectivity or power issues.

Description

• SentryPlus™ Alert Technology Universal Upgrade Kit detects

catastrophic discharge from the relief valve of an RPZ

(Reduced Pressure Zone) backflow preventer that can cause

flooding due to excessive discharge and/or a blocked/under-

sized floor drain

• Wirelessly issues multi-channel alerts (call, text, email)

• Can be installed without taking equipment offline

• The SentryPlus Alert Technology Universal Upgrade Kit sup-

ports three types of applications:

1. RPZ backflow preventer upgrades

2. New LFF113RFP Flood Protection ACV (Automatic

Control Valve) installations

3. Existing LFF113RFP Flood Protection ACV upgrades to

support SentryPlus Alert Technology

List of Parts

The kit consists of following components:

• Control Box with a power adapter

• Cellular Gateway

• Flood Sensor

• 2" PVC Tee with NPTF threaded end connections to mount

the Flood Sensor

• 6' 4-conductor electrical cable

• Mounting tabs, screws, and small flat head screwdriver

For existing LFF113RFP Flood Protection ACV upgrades, the

system requires an additional component:

• Relay Box with mounting bracket (sold separately)

Understanding Safety Information

This safety-alert symbol is

shown alone or used with

a signal word (DANGER,

WARNING, or CAUTION). A

pictorial and/or safety mes-

sage to identify hazards and

alert you to the potential for

death or serious personal

injury.

Identifies hazards which, if not

avoided, will result in death or

serious injury.

Identifies hazards which, if not

avoided, could result in death

or serious injury.

Identifies hazards which, if not

avoided, could result in minor

or moderate injury.

Identifies practices, actions,

or failure to act which could

result in property damage or

damage to the equipment.

This pictorial alerts you to the

need to read the manual.

This pictorial alerts you to

electricity, electrocution, and

shock hazards.

• Learn how to properly and safely use the equipment

BEFORE installing, setting up, using, or servicing.

• Keep the manual available for easy access and future

reference.

• Replace missing, damaged, or illegible manuals and

product labels.

• Read the manual and all product labels and follow all

safety and other information.

• Replacement manuals available at Watts.com.

WARNING

CAUTION

NOTICE

DANGER

WARNING

To avoid death, serious personal injury, property damage,

or damage to the equipment:

Important Safety Information

SentryPlus Alert

Technology Universal

Upgrade Kit

1. Installing the Flood Sensor

(Backﬂow RPZ Upgrades)

The Flood Sensor is installed in the discharge piping from the

RPZ relief valve. If the Flood Sensor detects water in the dis-

charge piping, it will signal the Control Box to close the valve.

1. Identify a location to mount the Flood Sensor. It can be

installed in either a 2" female NPT joint of your choice, or the

2" NPT tee included with the kit.

2. When using the supplied tee, install the sensor in the RPZ

discharge line in the HORIZONTAL position. Install the Flood

Sensor into the tee by screwing it in, ensuring that the

probes point downward as shown below.

3. Unscrew the black cap to access the sensor probes. Push

the two metal probes down until they touch the bottom of

the pipe, then pull them up at least ¼". The ends of the

sensor probes should be located between ¼" and ½ of

the pipe’s inner diameter from the pipe bottom. The probes

MUST NOT BE less than ¼" from the pipe wall. Hand

tighten the white plastic nuts on the probes to make it

water tight.

Ensure Flood Sensor probes do not contact pipe bottom or sides.

CAUTION

Installation and Operation

Flood Sensor

To Floor

Drain

From RPZ

Relief Valve

(with Air Gap)

Sensor Probes

Installed

4. If the sensor probes are too long, cut off the top of probes so

they fit properly when the cap is closed. To shorten the probe,

loosen and lower the terminal block located at the top of the

probe, then cut off the excess metal.

5. It's recommended that certified electrician should wire the sen-

sor to the Control Box, as described in the next section.

6. Place the cap back on.

NOTE: Upon installation & Wiring, terminal blocks should not

touch.

Tighten

nuts

If necessary,

cut excess

off the top of

the probe

When retrofitting an existing Model 113RFP Flood Protection ACV,

disconnect the electrical power before retrofitting the old Junction

Box to the new one.

CAUTION

2. Installing and Wiring/Retroﬁtting the Control Box

Installation and Operation

WARNING

Ensure that all power supply to the Control Box is turned

off before making any connections to the Control Box.

Failure to do so may result in electrocution, personal

injury, and /or death.

WARNING

Certified electrician to connect 110 VAC power and Control Box to

Relay Box.

NOTICE

During the retrofitting process on the 113RFP, the system

will not be monitoring for flood detection or protection..

NOTICE

For All Installations

The Control Box is designed to be mounted to a wall using the

mounting tabs and screws provided with the kit, or it can be

mounted on the ACV.

1. To open the Control Box, loosen the four screws located

on the corners of its cover to access the internals of the

Control Box.

2. Use a 300V, 14-24 AWG cable (not provided) to connect

the Flood Sensor to the Control Box. Insert one end of the

cable into wiring gland on the Control Box and attach two

wires to the terminals labeled FLOOD SENSOR. There is

no polarity.

3. Inset the other end of the cable into the opening on the

Flood Sensor. Attach one wire to each terminal block locat-

ed at the top of the probes. There is no polarity.

4. Optionally, use a cable to connect to a Building

Management System or alarm for remote indications of

a continuous water discharge at the terminals labeled

REMOTE TRIP. There is no polarity.

5. Using the four-conductor communications cable with the

kit, connect to the Cellular Gateway using the terminals

labeled WIRELESS. Insert the cable through the wiring

gland and attach one wire to each terminal. Cellular

Gateway connections will be described in the next section,

Installing the Cellular Gateway.

Adjusting the Time Delay

The Flood Sensor has a delay feature which starts a timer once

it detects water. The timer counts down before signaling that

there’s a discharge occurring. You can adjust the time delay to

avoid having the valve close due to intermittent or nuisance relief

valve discharge. The delay is adjustable from 0 to 120 seconds,

and the default is 60 seconds.

Adjust the time delay by pressing the + or - button in the Control

Box.

We recommend setting the delay between 3-60 seconds.

However, the ideal set point can vary widely depending on the

product application, including drain size, location, backflow

preventer, water pressure, and tolerance for discharge. For

example, if your backflow preventer releases water each time a

booster pump turns on upstream and you know it will release

water for 10 seconds before the system stabilizes, you can set

the time delay to 15 seconds.

• The terminal block accepts 14 to 24 AWG.

• Relay Box terminals have 24VDC/AC, 2A max.

• The Control Box uses an external 24VDC, 1.04A, 25W

supply. This also powers the Cellular Gateway.

• The Sensor Probe is passive.

Missing Image

Press + or –

to set the

delay time

Flood

Sensor

BMS

Connection

(Optional)

Installation and Operation

For New and Existing LFF113RFP ACV Installations

For convenience, new LFF113RFP ACVs are shipped with a

Solenoid prewired to the Relay Box. Retrofitting an existing

LFF113RFP requires an electrician to make that connection

manually. New and existing ACV systems both require wiring to

the Relay Box.

For Existing LFF113RFP Installations Only

1. After removing power from the circuit, disengage the wiring

from the main terminals inside existing Control Box:

• Terminals 1 and 2 (Flood Sensor)

• Terminals 3 and 4 (Solenoid)

• Terminals 5 and 6 (Remote Trip Indicator, if wired)

2. Remove the Control Box from the ACV or wall mount.

3. Replace the existing control box and mounting bracket with

the new Relay box and mounting bracket.

4. Using the cable from Solenoid, connect the Solenoid to the

Relay Box. Attach the cable to the terminals 5 and 6 in the

Relay Box. There is no polarity.

5. The Relay Box includes several spare terminals for your con-

venience to ease wiring requirements, such as building moni-

toring inputs or valve positioning.

For New and Existing LFF113RFP Installations

1. Using an electrical cable (not provided), connect terminals 3

and 4 in the Relay Box to 110VAC power.

2. Using a 300 V, 14-24 AWG cable (not provided), connect the

Relay Box to the Control Box. Attach one end of the cable

to terminals 7 and 8 in the Relay Box. Attach the other end

of the cable to the terminals labeled ACV in the Control Box.

Connect Terminal 7 to ACV+. Connect Terminal 8 to ACV-.

Solenoid Operation

The Solenoid is equipped with a Solenoid Bypass Valve (nor-

mally closed) which manually

closes the Main Valve when

engaged.

Opening the Solenoid Bypass

Valve pressurizes the Main

Valve cover as indicated by a

pressure gauge, closing the

Main Valve.

Closing the Solenoid Bypass

Valve and opening the Manual

Reset Ball Valve returns the

Main Valve to the full open

position.

The pressure gauge returns to

zero when the Main Valve is

fully open.

NOTE: Manual Reset Ball Valve must be closed for normal oper-

ation.

7, 8

3, 4

5, 6

When identifying a location to mount the Cellular Gateway,

the device must be placed away from large metal objects and

structures that can block cellular signal. Additionally, the cellu-

lar antenna is located on the upper right inner side wall of the

enclosure). When mounting, ensure that this of the device is

away from any walls, wires, pipes, or other obstructions, espe-

cially anything metallic.

1. Before mounting, apply power to the Cellular Gateway to

ensure there is adequate cell coverage. On startup, the CELL

LED will blink at a rate of 1sec. This indicates it is searching

for a cell connection. Once connected it turns steady blue.

If connection is poor, it will blink with short OFF pulse every

second. If there is a poor or no connection, find a new

location.

2. Mount the Cellular Gateway at the selected location, using the

mounting tabs and screws provided with the kit. Screws to

attach the unit to the wall are not included.

3. Using the four-conductor cable supplied with the kit, connect

the Control Box to the Cellular Gateway. Route wires from

the WIRELESS terminals of the Control Box through the

Cellular Gateway’s wiring gland and connect to the matching

terminals.

PWR to PWR

GND to GND

MOD+ to MOD+

MOD- to MOD-

Six feet of cable is supplied with the unit, but the Cellular

Gateway can be located up to 100 feet away from the

Control Box. If additional wire is used. it must meet the

required rating for the Control Box (300V, 14-24 AWG).

4. To prevent water or dust from entering the cellular gateway,

control box & relay box, tighten all wiring glands.

5. Apply power to the Control Box and Cellular Gateway.

1. Start-Up – Upon start-up, the POWER LED will light up

a steady green to indicate power is supplied. The Cellular

Gateway will automatically go into its start-up sequence.

During the start-up sequence, the CELL and IoT LED will

blink blue, indicating the Cellular Gateway is searching for a

cellular connection. This may take up to 10 minutes. Once

the cellular and Cloud connections are established, the CELL

LED and IoT LED will be steady blue.

2. Cellular Connection – After the start-up sequence is com-

pleted, the CELL LED will be a steady blue if there is a good

connection. It will blink with short OFF pulses if there is a

poor connection.

3. IoT Connection – If there is a Cloud connection, the IoT

LED will be a steady blue. IoT LED will blink if cloud connec-

tion is lost or not established. It will continue trying to connect

indefinitely.

NOTICE

If there is no Cloud connection, users will not receive notifi-

cations via Syncta.

4. Flood LED – If a flood event occurs, the FLOOD LED will be

a steady orange. It will remain on as long as there is a flood

condition.

5. Test Button – When cellular and Cloud connections have

been made, you can send a test message through the

Syncta app by pressing the TEST button.

6. Reset Button – You can reset the Cellular Gateway and

restart the start-up sequence by pressing the RESET button .

This will cause all on-going operations to cease.

Installation and Operation

3. Installing the Cellular Gateway

4. Setting Up the Cellular Gateway

WARNING

Ensure all power supply to the Cellular Gateway is turned off before

making any connections to the Cellular Gateway. Failure to do so may

result in electrocution, personal injury, and/or death.

Cellular Gateway

Cellular

Connection to

Internet

Wired to Control Box

1. Using a smart phone or tablet,

scan the QR code on the side

on the Cellular Gateway, or go

to https://connected.syncta.

com

2. When prompted, enter the

Device ID. The Device ID is the

set of numbers printed beside

the QR code on the side of the

Cellular Gateway.

3. Follow the prompts to create

a Syncta account, or if you are

an existing Syncta user, log in

to your account. The device

can be registered to multiple

accounts.

4. Once the device is regis-

tered to your account, follow

prompts to add notifications.

To manage alerts, login to your

account on Syncta.com.

Installation and Operation

5. Registering SentryPlus Alert

Valve Travel

VALVE SIZE - INCHES 11⁄411⁄22 21⁄23 4 6 8 10

Travel - Inches 3⁄83⁄83⁄85⁄83⁄41 11⁄22 21⁄2

Valve Cover Chamber Capacity

VALVE SIZE - INCHES 11⁄411⁄22 21⁄23 4 6 8 10

fl. oz. 44410 10 22 70

U.S. Gal 11⁄421⁄2

1. Open the Control Box. Apply power.

2. Pour an adequate amount of water into the RPZ Relief Valve

Air Gap until the DELAY counter begins to count down. This

indicates the Flood Sensor is properly installed and is sensing

water in the discharge piping.

3. Trap water in the discharge piping. The Solenoid will energize

when the duration of time delay elapses. The FLOOD LED will

be solid orange. The valve will close and must be manually

reset. Adjust the Time Delay to the customer/project specifi-

cations.

4. As a final test, simulate an actual RPZ Relief Valve discharge

and observe the floor drain for excessive pooling or flood-

ing. Re-adjust the time delay and Adjustable Closing Speed

Control as needed to achieve the desired valve closure time.

Start-up Instructions

Overview

This User Guide provides information about the different LED

lights, buttons, and connectors inside the SentryPlus Alert

Cellular Gateway, as well as troubleshooting suggestions if need-

ed.

For more information about the Cellular Gateway, see the

Installation, Operation, and Maintenance Manual.

Read this Manual BEFORE using this equipment.

Failure to read and follow all safety and use information can result

in death, serious personal injury, property damage, or damage to the

equipment. Visit Watts.com with any questions.

Keep this Manual for future reference.

WARNING

Startup Sequence

COLOR STATE DEFINITION

Steady Green Green LED turns on - when power is applied

Cell LED blinks Trying to establish a cellular connection.

IoT LED blinks Trying to establish a connection to the Watts Cloud.

When the Cellular Gateway powers up, the device goes through

a startup sequence. Below is the startup sequence that the

device will go through if everything is working correctly.

Cellular Gateway

Cellular

Connection to

Internet

Wired to Control Box

Flood

The FLOOD LED only turns on when excessive relief valve discharge from your backﬂow

assembly is detected.

COLOR STATE DEFINITION SOLUTION

Steady Orange Water is discharging from the relief

valve of your backflow assembly, and

it is more than a slight drip.

Note: This will only turn on if water

discharge is detected and delay timer

has reached 0.

If your device is registered, you will

receive a “flood notification” via text,

email and/or a phone call.

Blinking There is a problem with the Modbus

connection between the Control Box

and Cellular Gateway.

Check the wiring between the Control

Box and Cellular Gateway on page 11.

Off There is no discharge occurring. N/A

Cellular

The CELLULAR LED indicates whether or not a cellular connection is present.

COLOR STATE DEFINITION SOLUTION

Steady Blue A cellular connection is present. N/A

Short off blink The cellular connection is poor. See Poor or No Cellular Reception on

pages 7-8.

Blue blinking There is no cellular connection —

searching.

See Poor or No Cellular Reception on

pages 7-8.

IoT

The IoT LED indicates whether or not there is a connection to the Cloud.

COLOR STATE DEFINITION SOLUTION

Steady Blue There is a connection to

the Watts Cloud.

N/A

Blinking There is not a connection to

the Watts Cloud. Trying to establish

connection.

See No Connection to the Cloud on

page 9.

Power

The POWER LED turns on when power is supplied to the device.

COLOR STATE DEFINITION SOLUTION

Steady Green The device is turned on. N/A

Off If the device is plugged in, but this

LED is not on, the device is not

receiving power.

Check wiring to control box.

LEDs

The LEDs inside the Cellular Gateway indicate if a component/

connection is running, or if there is an issue. The following sec-

tions describe the different LED colors and blink patterns.

Buttons

The only buttons that you might need to use are the RESET and

TEST buttons. See the section below for more information. Both

can be used by user.

RESET

Press this to reset the Cellular Gateway and restart the device.

This will cause all ongoing operations to cease.

Note: You can also perform a full reset by removing power to the

Cellular Gateway for 10 seconds and then plugging it back in.

TEST

Press to have a test notification sent.

Note: The unit must have already been registered and commu-

nication preferences set for these notifications to be sent.

Terminals

Terminals wire to Control Box (PWR, GND, MOD+, MOD-).

Terminals labeled INPUT 1 & INPUT 2 are reserved for future use.

Power Outlet

Ground

MOD+

MOD-

Cellular Gateway

Cellular

Connection to

Internet

Wired to Control Box

Andere Handbücher für SentryPlus Alert

Inhaltsverzeichnis

Andere Watts Sicherheitssystem Handbücher

Watts

Watts SentryPlus 113RFP Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung