Watts Hydrosafe HSFS Technisches Dokument

Water Filtration Systems By Watts®

INSTALLATION, OPERATION

AND MAINTENANCE GUIDE

Models: HSFS & HSFS 5M

WARNING: Please read carefully before proceeding with installation. Failure to follow attached instructions or

Operating parameters may lead to the product’s failure. Please save this manual for future reference.

Table of Contents

Introduction, Specifications, and Warnings ...…………………………………………………… 4

Installation …………………………………………………………….…………………………. 5

Startup & Operation ………………...…………………………………………………………… 6

Maintenance ……………………………………………………………………………………... 6

Trouble Shooting ………………………………………………………………………………... 7

Replacement Parts ………………………………………………………………………………. 7

Introduction

Thank you for purchasing the Hydro-Safe® Filtration System. This system combines three

different technologies to meet your water treatment needs.

FIRST

Model HSFS: The water is filtered through a 0.2-micron high capacity depth filter. This filter

traps suspended particles, cysts, and bacteria.

Model HSFS 5M: The water is filtered through a 5-micron pleated filter, which traps

suspended particles.

Second

The water is treated with activated carbon, which, removes chlorine, organics, and other

objectionable chemicals that can affect the taste and/or smell of the water.

Third

The water is disinfected by the integral UV system. The UV system renders all biological

contaminants inactive.

Specifications

Material of Construction Glass Filled Poly Pro

Lid Closure Swing Bolt

Inlet / Outlet Connection 1”FNPT

Pressure Gauges (2 each) 0 - 200 psi

Overall Height 40”

Diameter 12”

Maximum Operating Pressure 125 PSI

Maximum Temperature 100° F

Maximum Flow Rate* 15 gpm

UV wavelength 254 nm

UV dosage (@ 14 gpm) > 40 mj/cm²at end of lamp life

Power, ballast 115 / 230 volt 60 / 50 htz. / <1 amp

Power, lamp 45 watts

* Higher flow rates can be achieved but the UV effectiveness will be reduced.

Warning:

•Do not use this product where the water is microbiologically unsafe or of unknown

quality.

•Do not look at the UV lamp while it is turned on. The intense UV light emitted from

the bulb will burn the eyes and can cause permanent damage.

Note: Avoid touching the sides of the quartz sleeve and UV lamp. Handle from the end

only. Fingerprints will reduce the effectiveness of the UV system.

Before installing this product, read all installation instructions and warnings carefully.

Failure to follow instructions can result in serious injury, death or property damage.

Installation:

1. The unit should be installed indoors. Make sure there is at least four feet of clear space

available above the unit. The space above the unit is necessary for cartridge and UV

lamp replacement.

2. Remove the union adapters from the package and put the union ring over the adapter.

Apply Teflon tape to the gauge threads and screw the gauges into the adapters (see figure

1).

3. Turn off the water supply.

4. Plumb the unit to the water supply line (see figure 1). It is recommended that ball valves

(not included with unit) be installed in the inlet and outlet piping for more convenient

filter cartridge and UV lamp replacement.

5. Remove the lid by loosening the swing bolts and verify that the filter cartridge and

stainless steel UV chamber are installed (see figure 2).

6. Replace the lid and tighten the swing bolts in a crisscross pattern.

7. Remove the retaining nut and carefully install the quartz sleeve and o-ring (see figure 3).

Do not touch the sides of the quartz or the lamp. The retaining nut only needs to be

finger tight. Note: Over tightening the retaining nut will cause the quartz sleeve to break.

8. Orient the UV lamp with the four-pin connector pointing up and gently lower the lamp

into the quartz sleeve (see figure 4). Do not drop the lamp into the sleeve (the sleeve

and/or lamp could break).

9. Make sure the power supply is not plugged in. Connect the plug from the power

supply to the four-pin connector on the lamp. Cover the end of the lamp with the vinyl

cap (see figure 5)

10. Attach the power supply to the side of the filter housing with the included Velcro.

Figure 3

Figure 4

Figure 5

Figure 2

Figure 1

Startup & Operation:

1. Slowly turn on the water supply.

2. Press the red pressure relief button on top of the housing. Hold the button down until

water comes out from underneath the button.

3. Check for and repair any leaks. If Necessary, tighten the swing bolts with a crescent

wrench or by sliding the shaft of a large screwdriver through the swing bolt eyelet.

4. Plug in the UV power supply. A green light on the power supply indicates that the lamp

is working properly. A red light and audible alarm indicates that the lamp is either

disconnected or has failed.

The system is now ready to provide filtered water. Periodically check the pressure gauges while

water is flowing through the system. Replace the filter cartridge if the difference between the

inlet and outlet pressures reaches 25 psi.

Maintenance:

Filter Cartridge – Replace every 6 to 12 months depending on feed water

quality or if the difference between the inlet and outlet pressure is greater

than 25 psi while water is flowing.

1. Unplug the UV power supply and allow the lamp to cool for 30

minutes.

2. Move the UV power supply so that it will not get wet.

3. Turn off the water supply to the unit and relieve the pressure by

pressing the red button on top of the unit, or by opening a faucet

down stream.

4. Remove the UV lamp and quartz sleeve by following the

installation instructions on the previous page of this manual in

reverse order. Place the sleeve and lamp in a safe place to prevent

breakage.

5. Loosen the eyebolts and remove the lid.

6. Remove the stainless steel UV vessel from the inside of the filter

cartridge by pulling it up and out (see figure 6). Set it aside for

reuse.

7. Rotate the filter cartridge counter clockwise and lift it out of the

housing (see figure 7).

8. Install the new cartridge by lowering it into the housing. Turn the

cartridge clock wise to lock it in place.

9. Reinstall the stainless steel UV vessel into the center of the

cartridge.

10. Replace the lid and tighten the eyebolts.

11. Replace (or reuse, depending on the schedule) the quartz sleeve and

lamp by following the installation instructions on the previous page

of this manual.

UV Lamp – Replace every 12 months

Figure 6

Figure 7

M-WWQP-HYDRO-1117

1. Unplug the UV power supply and allow the lamp to cool for 30 minutes.

2. Lift the UV lamp up and unplug the connector from the end of the lamp.

3. Replace the lamp and plug in the connector. Avoid touching the sides of the lamp.

4. Cover the lamp with the vinyl cap.

5. Plug in the UV power supply.

Quartz Sleeve – Clean every 12 months and replace every 24 months

1. Carefully remove the UV lamp. Avoid touching the sides of the lamp.

2. Remove the quartz sleeve-retaining nut.

3. Carefully remove the quartz sleeve.

4. Clean the quartz sleeve with standard glass cleaner or replace it with a new one. Avoid

touching the sides of the quartz sleeve.

Troubleshooting:

Problem

Corrective Action

Low flow or high differential pressure

Replace filter cartridge

Short filter cartridge life

Install a prefilter upstream of the unit

UV lamp alarm

Replace the UV lamp

Replacement Parts

Part Number

Description

HSFSCART-PAC

0.2 micron pleated carbon cartridge

HSFSCART-ACP

5 micron pleated carbon cartridge

HSFSLAMP

Ultraviolet Lamp

HSFSQUARTS

Quartz Sleeve

WUVBALLAST6-12

UV Power Supply

HSFSUVOR

Quartz Sleeve O-Ring

HSFSUVNUT

UV Retaining Nut

PG15L25

Pressure Gauge 0 – 200 psi

HSFSCOUPLING-T

Inlet and Outlet Coupling Adapter with Gauge Port

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Watts Wasserfiltersystem Handbücher

Watts

Watts IS-OR-NH Bedienungsanleitung

Watts

Watts FRIWAC Series Bedienungsanleitung

Watts

Watts SmartStream UV WB002 Bedienungsanleitung

Watts

Watts PWSYS-RO-MAN5 Bedienungsanleitung

Watts

Watts WQC4RO Bedienungsanleitung

Watts

Watts OneFlow OF210-1 Bedienungsanleitung

Watts

Watts IOM-WQ-PWSYS-FIL-ICE4 Bedienungsanleitung

Watts

Watts QTSTMMAX-2S-10M Bedienungsanleitung

Watts

Watts PWROKC4 Bedienungsanleitung

Watts

Watts SENTINEL LEAK DEFENSE LDS-3-075 Bedienungsanleitung

Watts

Watts OneFlow OFPSYS Bedienungsanleitung

Watts

Watts OneFlow Bedienungsanleitung

Watts

Watts WQT4 RO Series Bedienungsanleitung

Watts

Watts OF1465 Bedienungsanleitung

Watts

Watts Pure Water PWSYS-FIL-ICE2 Bedienungsanleitung

Watts

Watts WH-VIH1-SED-A-WHT-HSG Bedienungsanleitung

Watts

Watts PWDWLCV2 Pure Water Bedienungsanleitung

Watts

Watts Hydro-Safe QTBRWMAX-1S-1M Bedienungsanleitung

Watts

Watts ZRO-4 Bedienungsanleitung

Watts

Watts OneFlow OF110-1 Bedienungsanleitung

Watts

Watts AERCO 58015-04 Betriebsanleitung

Watts

Watts PWRO4ZRO Pure Water Bedienungsanleitung

Watts

Watts GTS450S Gebrauchsanweisung

Watts

Watts PWIOGAC2 Series Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung