wattstopper RT-100 Bedienungsanleitung
RT-100
Time Switch
Programmable Countdown
Installation Instructions
SPECIFICATIONS
Voltage ...............................................................120VAC, 60HZ
Load (Single Pole Circuit)
Incandescent or uorescent lamp .................. 0 — 600 Watt
Fan motor .................................................................. 1/6HP
Time Delay..............................................5 minutes to 12 hours
Environment .................................................... Indoor use only
Operating Temperature ............... 32° to 104°F (0° to 40°C)
Humidity ...................................... 95% RH, non-condensing
Tools Needed
Insulated Screwdriver
Wire Strippers
Please read all instructions before installing
Santa Clara, CA 95050
DESCRIPTION AND OPERATION
The RT-100 is a time switch that turns OFF the connected light or fan (load) when
the selected time expires. While the switch is OFF the pilot light behind the ON/
OFF button illuminates and “OFF” appears in the display. When the switch is ON,
the display shows the amount of time the load will remain ON.
For times up to 59 minutes and 59 seconds, the display shows a blinking colon
between the minutes and seconds while the seconds count down continuously.
For times between 1 hour and 12 hours, the display shows a blinking colon
between the hours and minutes and the minutes portion of the display changes
only once a minute. See Fig. 1.
The RT-100’s lighted alpha-numeric
display is also used for programming
functions. With the programming
functions, you can decide:
• Delay — the amount of time the switch
remains ON with the initial press of the
ON/OFF button.
• Sound — whether the switch beeps for
each button press and every 5 seconds
for 1 minute before it turns OFF.
• Flash — if the lights ash to warn you
that they are going to turn OFF. When
Delay is set for 10 minutes or more,
lights ash once at 5 minutes and once
at 1 minute before turning OFF. When
Delay is set for 5 minutes or less, lights
ash once 1 minute before turning off.
Manual ON
When you press the ON/OFF button, it activates the Delay timer. If you want to
keep the switch ON for a time different from what is programmed, simply press
and hold the ON/OFF button until the display shows the desired time. When you
let go of the button the switch turns ON.
Manual OFF
While the switch is ON and the timer is running, press the ON/OFF button to turn
OFF the connected load without delay.
Changing the amount of time: At any time, you can press and hold the ON/OFF
button for 1 second to restart the timer. It goes immediately to the programmed
Delay time; if you need a different amount of time, keep holding the button for
at least 2 seconds. Hold the button until the display shows the desired time.
Releasing the button starts the timer countdown.
Minute
Countdown
Hour
Countdown
Fig. 1: Timer Countdown Examples
The time-out period can be set for 5 minutes
to 12 hours. The time is displayed in two dif-
ferent ways. For a countdown of less than an
hour, the display shows minutes:seconds. The
seconds count down continuously. If the count-
down is more than an hour, the display shows
hours:minutes, the colon flashes every second
and the display changes every minute.
Seconds
Elapsed
:01
:02
:03
Call 800.879.8585 for Technical Support
WARNING
Disconnect power to the wall switch
box by turning OFF the circuit breaker or removing
the fuse for the circuit before installing the RT-100,
replacing lamps, or doing any electrical work.
INSTALLATION & WIRING
1.Prepare the switch box.
After the power is turned off at the circuit breaker
box, remove the existing wall plate and mounting
screws. Pull the old switch out from the wall box.
2.Identify the type of circuit.
In a Single Pole Circuit (see Fig. 2), two single
wires connect to two screws on the existing switch.
A ground wire may also be present and connected
to a ground terminal on the old switch. A neutral
wire should also be present in the wall box.
CAUTION
For your safety: Connecting a proper ground to the time switch provides
protection against electrical shock in the event of certain fault conditions.
If a proper ground is not available, consult with a qualified
electrician before continuing installation.
Only connect the RT-100 to a Single Pole Circuit. The RT-100 is not suitable
for 3-way switching. If the existing wiring does not match the description for a
Single Pole Circuit, you should consult with a qualied electrician.
3.Prepare the Wires.
Tag the wires currently connected to the existing switch,
so that they can be identied later. Disconnect the wires.
Make sure the insulation is stripped off the wires to
expose their copper cores to the length indicated by the
“Strip Gage,” in Fig. 3 (approximately 1/2 inch).
*URXQG
+27SRZHUIURP
FLUFXLWER[
/2$'
SRZHU
WRODPS
1(875$/
www.wattstopper.com
Fig 2: Typical Single Pole
Switch Wiring
Strip Gage
1/2"
12.7mm
Fig 3: Wire
Stripping
4.Wire the time switch.
Twist the existing wires
together with the
wire leads on the
time switch as
indicated in the
drawing. Cap them
securely using the
wire nuts provided.
See Fig 4.
• Connect the green
or non-insulated
(copper) GROUND
wire from the circuit
to the GROUND
terminal on the
RT-100.
• Connect the power
wire from the circuit
(HOT) to the black
wire on the RT-100.
• Connect the power
wire to the lamp or
fan (LOAD) to the red
wire on the RT-100.
• Connect the NEUTRAL wires
from the circuit to the white wire on the RT-100.
5.Put the RT-100 in the wall box with the display positioned above the
ON/OFF button.
Secure it to the wall box with the screws provided.
6.Restore power to the circuit.
Turn ON the breaker or replace the fuse.
7.Make any necessary programming changes.
See the Programming section for information.
8.Install cover plates.
Install industry standard decorator wall switch cover plate (not included).
TOP
INDOOR USE ONLY
Green
->
GROUND
Terminal
Black
->
HOT (power
from circuit box)
Y
Y
White
->
NEUTRAL
Red
->
LOAD (power
to lamp or fan)
Industry standard
switch cover plate
(not provided)
Fig 4: Switch orientation, wire connections
and wall box assembly
Call 800.879.8585 for Technical Support
PROGRAMMING
To program the time switch, you must access the programming buttons that are
located under the ON/OFF button. The wall switch cover plate must be removed
to gain access to the programming buttons.
1. Firmly grasp the side edges of the Lock Bar
and gently pull it away from the switch face
until it clicks. Do NOT attempt to pull the
Lock Bar off of the switch!
2. Push the ON/OFF button downward so that it
slides down approximately 1/2 inch to expose
the multi-function programming buttons.
The buttons are labeled from right to left:
Menu/Raisep: provides access to the
program items and shows their current
settings. With the rst press it shows
Delay time, second shows Sound setting,
third shows Flash setting. After an item
is Selected, the Raise button can increase
the setting or change it from O to On. For
the Delay setting, when you reach 1200 (12
hours), pressing Raise brings the display
around to 5:00 (5 minutes).
Select/Save: press this while a program item is displaying to change the
setting for the item. When the correct setting is in the display, press this again
to Save the setting for that item.
Lowerq: After an item is Selected, the Lower button can reduce the setting
or change it from On to O. For the Delay setting, when you reach 5:00 (5
minutes), pressing Lower brings the display to 1200 (12 hours).
TOP
INDOOR USE ONLY
LCD display
Menu
RaiseLower
06xxxr1
Select
Save
OFF
Programming Menu:
Delay 5:00 minutes
to 1200 hours
ON or off
Flash on or off
return to normal operation
TOP
INDOOR USE ONLY
Lock Bar
Menu
RaiseLower
06xxxr1
Select
Save
Programming
Buttons
Slide down
ON/OFF
Button
LCD display
OFF
www.wattstopper.com
Setting the initial time Delay
1. Press the Menu/Raise button ONCE to see the current Delay setting.
The factory setting for the Delay is 5 minutes, the minimum setting.
2. To change the setting, press the Select/
Save (middle) button.
3. Press the Menu/Raise button. The time
increases 5 minutes each time you press
the Raise button, until the time reaches 1
hour (100 ). After 1 hour, the time increases
15 minutes each time you press the button,
until it reaches 12 hours (1200), then it
goes back to 5 minutes (5:00). You can go
backwards at any point to reduce the time,
using the q Lower button.
4. When the desired time shows in the display,
press the Select/Save button to save the
setting and exit the programming mode.
Setting the Sound
1. Press the Menu/Raise button TWICE to see
the current Sound setting.
2. To change the setting, press the Select/Save (middle) button.
3. Press the Menu/Raise button to turn ON the warning and keypress sounds.
Press the q Lower button to turn OFF the warning and keypress sounds.
4. When the desired setting shows in the display, press the Select/Save button to
save the setting and exit the programming mode.
Setting the Flash
1. Press the Menu/Raise button THREE times to see the current Flash setting. If
a fan is connected to the switch, Flash should be O.
2. To change the setting, press the Select/Save (middle) button.
3. Press the Menu/Raise button to turn ON the warning ash. Press the q Lower
button to turn OFF the warning ash.
4. When the desired setting shows in the display, press the Select/Save button to
save the setting and exit the programming mode.
Call 800.879.8585 for Technical Support
5:00
10:00
15:00
... to
55:00
100
115
130
145
200
215
... to
1200
minutes
in 5-minute
increments
hours &
minutes
in 15-minute
increments
TROUBLESHOOTING
To test the time switch:
The pilot light behind the ON/OFF button should be ON when the switch is OFF
and OFF should appear in the display. Press the ON/OFF button. The connected
light or fan comes ON. The display shows the amount of time that the switch will
remain ON.
The connected light or fan should turn OFF in the number of minutes indicated by
the display. You can turn it OFF sooner by pressing the ON/OFF button again.
Light or fan will not turn ON (pilot light is visible):
Press ON/OFF button. The connected light or fan should turn ON. If not:
• Press and hold the button a second longer.
• Check the light bulb and/or motor switch on the fan mechanism.
• Turn OFF power to the circuit then check wire connections.
Light or fan will not turn ON (no pilot light or display is visible):
• Shade the switch from external light to make sure that the pilot light and
display are not ON.
• Make certain that the circuit breaker is ON and functioning.
• Turn OFF power to the circuit then check wire connections.
• Call 888.817.0517 for technical support.
Light or fan will not turn OFF:
• Press the ON/OFF button. If the connected light or fan does not turn OFF,
press the button and hold it a second longer.
• Turn OFF power to the circuit then check wire connections.
COVER PLATES
WattStopper RT wall switches t behind industry standard decorator style switch
cover plates.
www.wattstopper.com
WARRANTY INFORMATION
WattStopper warranties its products to be free of defects in materials
and workmanship for a period of ve (5) years. There are no obligations
or liabilities on the part of WattStopper for consequential damages
arising out of, or in connection with, the use or performance of this
product or other indirect damages with respect to loss of property,
revenue or prot, or cost of removal, installation or reinstallation.
Please
Recycle
2800 De La Cruz Boulevard, Santa Clara, CA 95050
Technical Support: 800.879.8585 • www.wattstopper.com
2800 De La Cruz Boulevard, Santa Clara, CA 95050
800.879.8585 • www.wattstopper.com
06249r4 3/2013
Please
Recycle
Inhaltsverzeichnis
Andere wattstopper Schalten Handbücher
wattstopper
wattstopper EMTS-100 Bedienungsanleitung
wattstopper
wattstopper WI-200 Bedienungsanleitung
wattstopper
wattstopper intelliswitch TS-400-24 Bedienungsanleitung
wattstopper
wattstopper PW-100-24 Bedienungsanleitung
wattstopper
wattstopper LMSW-105 Bedienungsanleitung
wattstopper
wattstopper WI-200 Bedienungsanleitung
wattstopper
wattstopper PW-203 Bedienungsanleitung
wattstopper
wattstopper LMSW-102 Bedienungsanleitung
wattstopper
wattstopper PW-100-24 Bedienungsanleitung
wattstopper
wattstopper LVSW Series Bedienungsanleitung
