Waudio CR-6 Bedienungsanleitung

ENGLISH

www.prolight.co.uk

USER MANUAL

CR-6 MIXER

PROFESSIONAL 19” RACK MIXER

Order Code: MIXE01

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Do not carry the unit with only one handle. Always carry using both handles.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

Features

• Six lines including one phono, three microphone inputs

• Microphone 1 is equipped with auto-override, sensitivity adjustment, delay time, EQ, and gain.

• Balanced microphone inputs on front and rear panels

• (Front panel) Channel on/off switches

• Dual zone assignment for all inputs

• Two zone outputs with gain, pan, EQ, and stereo/mono selection

• Zones have unbalanced and balanced outputs with master gain reduction

• Headphone output with volume control

Front panel:

1. Input gain knobs (6 channels): Control individual source levels.

2. On/off switches: Allow input sources to be individually selected.

3. Zone assign: Determines which zone the audio is directed to. The A+B position sends audio to

both Zones.

4. Microphone 1 Gain control: Controls the mic volume for the Neutrik combo connector on the

front panel.

5. Microphone EQ controls: Adjusts the Treble, Mid and, Bass frequencies of the microphone inputs.

6. Neutrik Combo Connector: Allows connection of either a 1/4” jack or an XLR plug.

7. Zone Knob:Controls the output level.

8. Mono/ Stereo: Selects the mode for the sound output.

9. Pan: Controls the mix of stereo audio. Moved to the left only the left speakers will be heard, or to

the right for the right speakers.

10. Level Indicator: Shows the level of sound output.

11. Zone EQ: Adjusts the Treble, Mid and Bass frequencies of the zoned audio.

12. Headphone Gain Control: Adjusts the headphone volume.

13. Headphone Jack: for headphones connection.

Features

Rear view:

14. Power Switch: Turns the unit on and off.

15. Power supply input: Insert the power adapter before switching on.

16. Balanced Zone B outputs: 1/4” stereo balanced 1/4” jack connectors controlled by the

Zone B knob.

17. Balanced Zone A outputs: Balanced stereo XLR connectors controlled by the Zone A knob.

18. Master Gain Reduction: Sets the output level of the Zone A outputs from 0.245V to 2.5V to

match the optimum inputs of ampliers.

19. Unbalanced Zone Outputs: Output controlled by the Zone knobs.

20. Record Output: Mix of output sent to either zone.

21. Unbalanced Line Inputs: For connection of DVD players, CD players, tuners, or other

mixing consoles.

Note: a. Plug mono audio sources into both Left and Right inputs using a “ Y “ cable connector.

b. Line 3 can receive a turntable input depending on phono/line switch position.

22. Phono/Line Switch: Select the appropriate position for your input device. With phono selected

the input signal is fed directly to the high-quality RIAA phono pre-ampliers so use this input only

for turntables. Line level sources will overload the sensitive phono pre-amps. Switch this over to

the Line position for line devices such as CD players and mixing consoles.

23. Ground connection: Use these connections with your turntables’ grounding cable to avoid

signal hum.

24. Combo Jack/XLR connector: Allows connection of either a 1/4” jack (line level) or an XLR

(microphone level) depending upon switch (25) position.

25. Mic/Line switch: Balanced XLR input for microphones, balanced Jack input for line level sources

26. Auto-Talkover Control: Sets the front panel Microphone to automatically reduce other source

levels when the mic is spoken into. Positions are available for either, -12dB, and -40dB

(complete reduction).

27. Talkover sensitivity adjustment: Determines the point in which auto-override activates.

The more sensitive the adjustment, the quieter you need to speak into your microphone to

activate auto-talkover.

28. Delay Time: Changes the speed and the music inputs return to normal volume after a

microphone is used. The time the music takes to return to the pre-set volume varies

from 0.5~ 4 seconds.

Connections (set up)

There are many options available for your individual needs and the diagram below is just one

example for your reference. Make sure all knobs are at “ zero “ and all devices are off. First, connect

all input sources; next, connect the stereo outputs to the power ampliers and/or audio receivers

such as CD players. Plug your mixer into the AC power supply. Now you are ready to switch

everything on.

Important: Always switch on your audio input sources such as turntables or CD players rst, then

your mixer, and nally ampliers. When turning off, always reverse this operation by turning off am-

pliers, then your mixer, and then input devices.

Note: Incorrect connection will result in malfunction. Make sure the connection is correct before

operation.

Specications

10k input impedance

Line

140mV rms sensitivity ( for 1.4V balanced output )

10K input impedance un-balanced

Mic 1 1.5mV rms sensitivity ( for 1.4V balanced output);

60mV rms max input

10K input impedance

Inputs

Mic2/ Mic3 1.5mV rms sensitivity ( for 1.4V balanced output);

80mV rms max input

Line 9V rms max

Headphone 0.5 Watt into 47 ohmOutputs

Distortion Less than 0.01%

Line > 87dB

Mic1 > 72dB

Mic2/Mic3 > 72dB

S/N ratio (vs. max output )

Phono > 70dB

Line 20 ~ 22KHz +/- 0.5dB

Mics 20 ~ 20KHz +/-1.5dBFrequency Response

Phono +/- 1dB except for controlled attenuation of -3dB

@20Hz to reduce rumble and feedback

Bass +/- 20 dB

Equalizations

( Mic1/Zone A/ Zone B) Middle +/- 15 dB; Treble +/- 14 dB

Power supply +/-15VDC

Dimension (W ×D ×H) 483 (W) x 200 (D) x 44( H) mm

Net weight 2.2 KGS

Inhaltsverzeichnis

Andere Waudio Musikequipment Handbücher

Waudio

Waudio DP 306 Bedienungsanleitung

Beliebte Musikequipment Handbücher anderer Marken

DAPAudio

DAPAudio IPS-PT Bedienungsanleitung

Dynacord

Dynacord DPM 8016 Bedienungsanleitung

Subdecay

Subdecay Starlight Flanger Bedienungsanleitung

Moen

Moen GEC8 Live Bedienungsanleitung

Fender

Fender 1 Bedienungsanleitung

Yamaha

Yamaha MLC-16 Bedienungsanleitung

Sonuscore

Sonuscore TIME TEXTURES Bedienungsanleitung

flight of harmony

flight of harmony V'Amp Bedienungsanleitung

NANO

NANO PERFORMANCE MIXER Bedienungsanleitung

Tascam

Tascam CD-GT2 Bedienungsanleitung

BHI

BHI NEIM 1031 MKII Bedienungsanleitung

Befaco

Befaco KICKALL Bedienungsanleitung

Paia

Paia 9720 Leitfaden

limex

limex ALPIN MASTER 128 Bedienungsanleitung

nord

nord Electro 3 Bedienungsanleitung

Joemeek

Joemeek sixQ2 Bedienungsanleitung

CARVIN

CARVIN 500W STEREO POWER MODULE - SCHEMA REV G Bedienungsanleitung

Furutech

Furutech ADL GT40 Installationsanleitung