Waveshare High-Precision AD/DA Board Bedienungsanleitung
High-Precision AD-DA User Manual
1
Revision: 1.2. Date: October 30 2015. Author: Zhou Jie. Editor: Felix
share awesome hardware
High-Precision AD/DA Board
User Manual
Overview
There's no AD/DA function on the
Raspberry Pi GPIO interface, this may
troubled you in the Pi development.
However, it won't be a problem anymore.
The High-Precision AD/DA Board allows you
to add high-precision AD/DA functions to
the Raspberry Pi.
Supported Pi
Raspberry Pi 1 Model A+
Raspberry Pi 1 Model B+
Raspberry Pi 2 Model B
Features
Onboard ADS1256, 8ch 24bit high-precision ADC (4ch differential input), 30ksps sampling rate
Onboard DAC8532, 2ch 16bit high-precision DAC
Onboard input interface via pinheaders, for connecting analog signal
the pinout is compatible with Waveshare sensor interface standard, easy to connect
various analog sensor modules
Onboard input/output interface via screw terminals, for connecting analog/digital signal
Features AD/DA detect circuit, easy for signal demonstration
High-Precision AD-DA User Manual
2
Revision: 1.2. Date: October 30 2015. Author: Zhou Jie. Editor: Felix
share awesome hardware
What's on Board
1. Raspberry Pi GPIO interface: for connecting with the Pi
2. AD/DA input/output: screw terminals
3. AD input: pinheaders, the pinout is compatible with Waveshare sensor interface standard, easy
to connect various analog sensor modules
4. 7.68M crystal
5. LM285-2.5: provides reference voltage for the ADC chip
6. Photo resistor
7. LED output indicator
8. 10K potentiometer
9. DAC8532: 16bit high-precision DAC, 2ch
10. Power indicator
11. ADS1256: 24bit high-precision ADC, 8ch (4ch differential input)
12. ADC testing jumper
13. DAC testing jumper
14. Power selection jumper
15. ADC reference ground configuration: when AD single inputted, the AINCOM is reference
terminal, can be connected to GND or external reference voltage
High-Precision AD-DA User Manual
3
Revision: 1.2. Date: October 30 2015. Author: Zhou Jie. Editor: Felix
share awesome hardware
Symbol descriptions
1) AD/DA input/output (Tab 2)
AD0-AD7: Analog input
AGND: Analog ground
GND: Digital ground
VCC: Power supply (3.3V and 5V optional, can be switched by setting the Power selection jumper)
DA0-DA1: Analog output
2) Analog input (Tab 3)
AD0-AD7: ADS1256 analog input
D0-D3: GPIO of ADS1256 (See ADS1256 datasheet)
P22-P25: GPIO of Raspberry Pi
AGND: Analog ground
3) LDR: Light-dependent resistor, i.e. Photo resistor (Tab 6)
By connecting the jumper between AD1 and LDR, the MCU can read the voltage output of LDR
from the pin AD1.
4) LEDA/LEDB: LED output indicator (Tab 7)
By connecting the jumper between LEDA/LEDB and DAC0/DAC1, the voltage output of
DAC0/DAC1 can be estimated roughly by the brightness of LEDA/LEDB.
5) ADJ: The adjustable resistor of the 10K potentiometer (Tab 8)
By connecting the jumper between AD0 and ADJ, the MCU can read the voltage output of the
potentiometer from the pin AD0
6) PWR LED: Power indicator (Tab 10)
7) Power selection jumper (Tab 14)
VCC: Power supply selection
VREF: Reference input voltage
3V3: 3.3V output
5V: 5V output
8) JMP_AGND: Analog ground jumper(Tab 15)
For single-ended measurements, use AINCOM (Analog input common) as common input, which
can be connected to AGND or external reference voltage. For differential measurements, do not
use AINCOM.
High-Precision AD-DA User Manual
4
Revision: 1.2. Date: October 30 2015. Author: Zhou Jie. Editor: Felix
share awesome hardware
1. Basic operation of Raspberry Pi
Before using the module with Raspberry Pi, such basic operations are required:
Using Raspberry Pi image
Using Linux Terminal
If you have already known them, please skip this section directly.
1.1. How to use Raspberry Pi image
1) Download the Raspbian image from http://www.raspberrypi.org/downloads/
2) Unzip the downloaded file and get an .img file.
3) Run the software Win32DiskImager.exe then select the Image File (the .img file) and Device(The
TF Card Reader), click the button write to program the system image file. Note: The capability of
TF card in used here should be more than 4GB. In this operation, a TF card reader is also
required.
4) Plug in the programmed TF card to the TF card socket on a Raspberry Pi, and then power up to
start the Raspbian OS. (System Configuration may be required for the first time boot up)
1.2. How to use the terminal of Raspberry Pi?
All the supported software should run under the Linux terminal. If you have a HDMI monitor, just
connect it to the Pi directly then open the terminal at the GUI. If not, you can operate the terminal of
Pi using SSH.
1) Connect the Pi and a router via a network cable.
2) Run the software PuTTY on the PC connected to the router, fill the IP address and Port of the Pi.
You can get the Pi’s IP from the router. And the Port is 22 by default.
3) Connection type is set to SSH.
4) Click the button Open to enter the Pi’s terminal. At the first boot up, please input:
User name: pi
Password: raspberry
High-Precision AD-DA User Manual
5
Revision: 1.2. Date: October 30 2015. Author: Zhou Jie. Editor: Felix
share awesome hardware
2. Getting started
The following API source codes should be run under the bcm2835 library, which can be downloaded
from http://www.airspayce.com/mikem/bcm2835/
2.1. Analog to digital conversion
1) Connect the High-Precision AD-DA Board to the Raspberry Pi.
2) Jumper settings:
Set the Power Supply to 5V: connect the pin 5V and VCC.
Set the Reference Input Voltage to 5V: connect the pin 5V and VREF.
Set the Potentiometer output as an Analog Input: connect the pin ADJ and AD0. Make sure the
left side Sensor Interface AD0 is disconnected.
Set the LDR output as an Analog Input: connect the pin LDR and AD1. Make sure the left side
Sensor Interface AD1 is disconnected.
Connect AINCOM to AGND. When using AD for differential measurements, the common input
AINCOM does not need to be tied to ground.
3) When using SSH for terminal control, please connect the network cable. The software PuTTY
should be installed. See the section 1.2.
4) Power up.
5) Copy (using a USB drive as a carrier) the software directory, ADS1256, to the Raspbian OS. Note:
the system will detect the USB drive directly under GUI, else if using SSH Connection, the USB
drive cannot be operated until it is mounted to the Linux. Search the key words “Linux mount”
for more details.
6) Make the files:
Enter the directory ADS1256, and execute make to compile it.
7) Execute sudo ./ads1256_test
Note: if it prompts command not found, please use chmod +x ads1256_test to add
execute permission.
8) Block the LDR from light and then the voltage of channel AD1 will be changed.
9) Turn the potentiometer and the voltage of channel AD0 will be changed.
10) In the end, press Ctrl+C to suspend the current process.
2.2. Digital to analog conversion
1) Connect the High-Precision AD-DA Board to the Raspberry Pi.
High-Precision AD-DA User Manual
6
Revision: 1.2. Date: October 30 2015. Author: Zhou Jie. Editor: Felix
share awesome hardware
2) Jumper settings:
Set the Power Supply to 5V: connect the pin 5V and VCC.
Set the Reference Input Voltage to 5V: connect the pin 5V and VREF.
Connect the pin DA0 to LEDA, the pin DA1 to LEDB. Then the brightness of LEDA indicator will be
changed according to the voltage output of DA0 and the brightness of LEDB indicator will be
changed according to the voltage output of DA1.
3) When using SSH for terminal control, please connect the network cable. The software PuTTY
should be installed. See the section 1.2.
4) Power up.
5) Copy (using a USB drive as a carrier) the software directory, DAC8532, to the Raspbian OS. Note:
the system will detect the USB drive directly under GUI, else if using SSH Connection, the USB
drive cannot be operated until it is mounted to the Linux. Search the key words “Linux mount”
for more details.
6) Make the files:
Enter the directory DAC8532, and execute make to compile it.
7) Execute sudo ./dac8532_test
Note: if it prompts command not found, please use chmod +x dac8532_test to add
execute permission.
8) Expected result: the brightness of LEDA and LEDB changes gradually.
High-Precision AD-DA User Manual
7
Revision: 1.2. Date: October 30 2015. Author: Zhou Jie. Editor: Felix
share awesome hardware
3. Interface Definition
Pin
Symbol
Description
1, 17
3.3V
Power supply (3.3V)
2, 4
5V
Power supply (5V)
3, 5, 7, 8, 10, 18, 22,
24, 26, 27, 28, 29,
32, 36, 38, 40
NC
NC
6, 9, 14, 20, 25, 30,
34, 39
GND
Ground
11
DRDY
ADS1256 data ready output, low active
12
RESET
ADS1256 reset input
13
PDWN
ADS1256 sync/power off input, low active
15
CS0
ADS1256 chip select, low active
16
CS1
DAC8532 chip select, low active
19
DIN
SPI data input
21
DOUT
SPI data output
23
SCK
SPI clock
31, 33, 35, 37
GPIO
extend to sensor interface
High-Precision AD-DA User Manual
8
Revision: 1.2. Date: October 30 2015. Author: Zhou Jie. Editor: Felix
share awesome hardware
4. Revision history
Revision
Changes
Date
1.0
Initial release
June 26 2015
1.1
Released English version manual
Minor edits
July 17 2015
1.2
Changed “DAC8552”to “DAC8532”.
October 30 2015
Inhaltsverzeichnis
Andere Waveshare Computerhardware Handbücher
Waveshare
Waveshare E9 Bedienungsanleitung
Waveshare
Waveshare Accessory Shield Bedienungsanleitung
Waveshare
Waveshare DVK512 Bedienungsanleitung
Waveshare
Waveshare XNUCLEO-F030R8 Bedienungsanleitung
Waveshare
Waveshare XNUCLEO-F030R8 Bedienungsanleitung
Waveshare
Waveshare Pico-BLE Bedienungsanleitung
Waveshare
Waveshare WM8960 Bedienungsanleitung
Waveshare
Waveshare DVK512 Bedienungsanleitung
Waveshare
Waveshare SIM7600 Series Bedienungsanleitung
Waveshare
Waveshare Music Shield Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
