Wavetronix Click 600 Datenblatt
www.wavetronix.com
801.734.7200
Click 600 Cabinet Interface
INSTALLATION QUICK START GUIDE
1Place the 600 in the cabinet
Included with Click 600 is an AC power cord. Connect it from your AC
power source to the IEC connector on the back of the device. The Click
600 will take that AC power and convert it to DC, then send that power
to any connected sensors (which run on 10–28 VDC).
Note. Next to the IEC connector is a switch that turns power on/o for
the whole device. During normal operation, be sure that this switch is
turned on.
Then decide how you’re going to install the Click 600 in the cabinet.
There are two ways you could do this:
˽Place the device on a shelf in the cabinet
˽Use mounting brackets (must be ordered separately) to mount
the device on the side of the cabinet.
The Click 600 has four plugs for SmartSensors, located on the back of the device. For each sensor you want to
connect to the Click 600, do the following:
1 Remove one of the plugs from the back (they are numbered 1–4; you’ll need to keep track of which
sensor is plugged into which port).
2 Terminate the conductors from the cable into that plug, following the labels on the plug (as
shown at left), then reconnect the plug to the Click 600.
3 Power to each sensor is toggled on the front of the device (see next section for more
information); make sure the switch is turned on.
2Terminate sensor cables
Note. The Click 600 is a cabinet interface device that provides power, surge protection, and
communication to up to four SmartSensor Matrix or Advance sensors. It provides the same func-
tionality as Wavetronix full and segmented backplates, but with a smaller cabinet footprint.
The Click 600 provides up to 64 channels of sensor detection output to contact closure devices
that are connected to the device via jumper cables.
WX-500-0317
© 2020 Wavetronix LLC. All rights reserved. Protected in the US by patents viewable at www.wavetronix.com/en/legal. Protected by Canadian Patent Nos. 2461411; 2434756; 2512689; and European Patent Nos. 1435036;
1438702; 1611458. Other US and international patents pending. Wavetronix, SmartSensor, Click, Command and all associated logos are trademarks of Wavetronix LLC. All other product or brand names as they appear are
trademarks or registered trademarks of their respective holders. Product specifications are subject to change without notice. This material is provided for informational purposes only; Wavetronix assumes no liability
related to its use.
3Connect the data ports to contact closure devices
If you look at the faceplate of the device, you’ll notice that it’s divided into two buses:
Data and Control. The data bus is for taking detection data from the sensors and send-
ing them to contact closure devices. Its faceplate interface consists of four RJ-11 jacks.
Use the jumper cables included with your Click 600 to connect from these jacks to your
contact closure devices. Information on how to use contact closure devices can be
found in the Click 100–400 Series user guide.
The data bus portion of the faceplate also has the following features: next to each RJ-11
jack is a switch that turns power on and o to the associated sensor; under each jack is
an LED that illuminates when the associated sensor has power.
4Use the control but to configure the sensors
The lower portion of the faceplate has the ports that make up the physical interface
of the control bus. These ports allow you to configure any sensors connected to the
Click 600. You can connect to the Click 600 and thereby to the sensors using any of
the following options:
˽RJ-11 jacks – The Click 600 has two RJ-11 jacks that allow you to connect via
RS-485.
˽USB port – Next to the RJ-11 jacks is a USB mini-B port for connecting via
USB.
˽DB-9 connector – Under the USB port is a DB-9 connector for connecting via
RS-232
˽T-bus port – At the bottom of the faceplate is a T-bus connector. You can use
this to make the Click 600 part of a shared power and RS-485 communica-
tion bus. This isn’t usually necessary because the Click 600 performs all basic
necessary functions, but it is an option.
Once you’ve made a physical connection from any of these control bus ports to your computer, you should be able to open
the SmartSensor Manager software on that computer and connect to any sensors that are connected to the Click 600. You
can now configure and manage those sensors.
Inhaltsverzeichnis
Andere Wavetronix Stromversorgung Handbücher
