Wavetronix Click 513 Bedienungsanleitung

Click 513 Trac Alert

QUICK START GUIDE

2Wire power and communication

If you are using a Click 200 surge protector with the Click 513, power and communication are provided to

the Click 513 through the T-bus (see the Click 200 Quick-Reference Guide). If you don’t have a Click 200

surge protector, use the following steps to wire power and communication into the Click 513:

1 Plug a T-bus 5-screw terminal block into the rst T-bus connector.

2 Wire DC power (10–30 V) from the power supply into the rst screw terminal on the 5-screw terminal

block; wire -DC into the second screw terminal.

3 Connect RS-485 communication (+485, -485 and GND) to either the remaining three screw terminals

on the 5-screw terminal block or to the screw terminals in the pluggable screw terminal block on the

top of the Click 513 (see labels for correct wiring).

e Click 513 has three other communication ports.

˽RJ-11 jack – Connect a jumper cable here for RS-485

communication

˽DB-9 connector – Connect a straight-through cable

here for RS-232 communication

˽RS-232/RS-485 terminals – On top of device; usually

not used

www.wavetronix.com

801.734.7200

1Mount the device

e Click 513 mounts over a T-bus for power and communication:

1 If the Click 513 was shipped with the T-bus connector attached, remove

the connector from the module.

2 Snap the connector onto the DIN rail by positioning it over the rail

with the male connector pointing to the right. Hook one arm over the

edge of the DIN rail and press down on the other arm until it snaps into

place.

3 Connect the T-bus connector to the rest of the T-bus by sliding them

together until you hear them snap into place.

4 Mount the Click 513 onto the DIN rail: position it properly over the T-

bus connector, hook the lip over the lower edge of the DIN rail, and use

a rocking motion to snap the module into place.

3Wire contact closures

e purpose of the Click 513 is to poll the SmartSensor HD for up to four approach’s worth of output data

(vehicle volume, speed and occupancy), and then to signal contact closure output 1 and/or 2 if the data is

indicative of a specic trac condition. is information that is reported can be monitored through the rst

digital outputs on the rst block on the bottom of the device. If you are wiring directly to a contact closure

input device, wire the output O1+ and O1-(common ground) to the input terminals. If you need to wire to a

relay, consider the Click 120. If your system requires use of a contact closure rack card (Click 112/114), then

establish a communication link via the RS-485 top/ front port.

Once in Device Setup mode (see Part 6), ensure that the contact closure device can communicate with the

Click 513. Once the contact closure device is set up, wire into the contact closure output terminals on the

device.

4Use on-device conﬁguration features

Next, use the device’s conguration features to make sure the

Click 513 is wired and working properly. e Click 513 has four

LEDs that monitor device activity and help you select tasks and

operating modes. It also has two banks of LEDs: one of yellow

LEDs that represent submenu 1 and one of red for submenu 2.

Check the LEDs to make sure the device has power.

e Click 513 also has a push-button, labeled Mode Switch,

used for selecting tasks and operating modes.

Yellow LEDs

Red LEDs

Multicolored LEDs

Button

Main Menu

Sub Menu 1

Sub Menu 2

5How to use the push-button to navigate through mode and task menus

Select a task or operation function by navigating through the main menu (multicolored LEDs) and the sub-

menus (yellow and red LEDs) using the push-button as described below:

LED activity-indicating functions:

Red – Shows device has power

Green – Shows device is transmitting data

Yellow – Shows device is receiving data

The blue LED has no activity-indicating function

1 Enter the main menu and cycle through it by

holding the push-button down.

2 Release the push-button once the cycle reaches

the desired mode.

3 Press the push-button again to select the mode.

Once selected, the mode will either start running

or the rst submenu (yellow LEDs) will start.

4 Hold the push-button to cycle through the rst

submenu.

5 Release the push-button once the desired sub-

menu selection is displayed.

6 Press the push-button again to select the func-

tion. e function will now run.

6Device Setup mode

Click Supervisor will be used to congure the Click 513. Follow these steps to install and connect to Click

Supervisor:

1 Download the setup le from www.wavetronix.com (under Support).

2 Double-click on the le to run the setup wizard. Follow the steps to install.

3 Manually copy the 513 driver les into the “Program Files\ClickHome\513” directory.

4 Using the DB-9 connector on the front of the module, make a connection between the Click 513 and

the computer.

Use Device Setup mode to congure threshold values and other settings using Click Supervisor.

5 Hold the push-button down, then release when the green LED comes on.

6 Press the push-button to select.

7 Run Click Supervisor and select Communication. is screen lets you pick the type of connection, se-

rial or IP. e Click 513 must be congured using serial communication.

8 Click Settings to make any necessary changes to the settings, such as the port. Click OK to return to the

communication screen, then click Connect. Keep the Click ID set to 0.

9 In the next screen, Click Supervisor will display all the devices it discovers. When the Click 513 appears,

select it and click Select. Click Supervisor will connect to the device.

10 Click Setup Click and select Expert from the driver list.

11 When the driver is loaded, click on the 513 tab. You will then see tabs labeled General, resholds and

Output.

7Conﬁgure the module

General Tab

˽Sensor ID – Displays the specic sensor ID number for the SmartSensor

HD.

˽Senser Interval (sec) – Displays the interval congured on the Smart-

Sensor HD in seconds.

˽Alert On Time (Multiple of Sensor Interval) – Allows you to enter the

number of intervals the Click 513 will use to determine the trigger on

alert status.

˽Alert O Time (Multiple of Sensor Interval) – Allows you to enter the

number of intervals the Click 513 will use to determine the trigger o

alert status.

˽Logic – Determines logic used to qualify an interval (AND requires all

enabled conditions to be true; OR requires only one enabled condition to

be true).

˽Poll Interval – Denes how frequently the Click 513 polls the SmartSen-

sor HD for interval data.

NOTE. e Click 513 can handle four approaches, for both directions of the

roadway.

WX-500-0197

2512689; and European Patent Nos. 1435036; 1438702; 1611458. Other US and international patents pending. Wavetronix, SmartSensor, Click, Command and all associated logos

are trademarks of Wavetronix LLC. All other product or brand names as they appear are trademarks or registered trademarks of their respective holders. Product speciﬁcations are

subject to change without notice. This material is provided for informational purposes only; Wavetronix assumes no liability related to its use.

Approaches Tabs

ere is one sub-tab for each approach under the main Approaches tab. Each

enabled variable for the specied approach will qualify an interval if the de-

tected value exceeds the set threshold.

˽Over Speed – qualies if average speed is above set threshold

˽Under Speed – qualies if average speed is below set threshold

˽Over Occupancy – qualies if occupancy is above set threshold

˽Under Occupancy – qualies if occupancy is below set threshold

˽Over Volume – qualies if total volume is above set threshold

˽Under Volume – qualies if total volume is below set threshold

8Run mode

9Reset

To reset the Click 513, follow the steps below:

1 Hold the push-button down, then release when the red LED starts ashing.

2 Press the push-button to select. e rst yellow LED will turn on to let you use that submenu.

3 Hold down the push button again to cycle between the following options:

˽Yellow 1 – Resets all settings except Serial Number and XML variable map

˽Yellow 2 – Resets all settings except Serial Number

4 Release when you reach the one you want. Press the push-button to select.

Aer the device is reset, it will return to the last mode that it was in.

Once the device has been congured, set it to Run mode to start retrieving trac data.

1 Hold the push-button down, then release when the blue LED turns on.

2 Press the push-button to select. e red and blue lights will turn on, and the yellow light will ash as

data is received.

In run mode the Click 513 polls data from the SmartSensor HD on the RS-485 T-bus port and compares the

detected values to the thresholds set in Click Supervisor. You can use a serial terminal program to view text

status information on your computer.

Note. e Click 513 communicates at 9600 bps.

Output Tab

˽Time Zone – Allows you to select the appropri-

ate time zone.

˽Morning/Afternoon Start/Stop Time – Begin-

ning and end times that the alerts will operate to

turn on/o during the morning/aernoon hours.

Lanes Tab

ere is one sub-tab for each lane under the main

Lanes tab. Each enabled variable for the specied

approach will qualify an interval if the detected value

exceeds the set threshold. e settings are the same as

the Approaches tab.

Andere Handbücher für Click 513

Inhaltsverzeichnis

Andere Wavetronix Sicherheitssystem Handbücher

Wavetronix

Wavetronix Click 512 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung