Wayne-Dalton ADV-X 888 Bedienungsanleitung

www.wayne-dalton.com 827802-0001 Rev - 1

Some installation tasks listed in

this document are found in other

documents.

Please refer to the appropriate

document(s) as directed;

827804 Installation Instructions

VFD for High Speed Metal Doors

(Included)

308577 Hilti Kwik Bolt Installation

found on Ribbon Connect

This installation manual provides

the trained door technician

information required to install a

ADV-X High Speed Metal door.

READ COMPLETE INSTRUCTIONS

BEFORE INSTALLING DOOR.

This manual is intended ONLY

for professional use by a trained

door systems technician. All

others please refer to the end

user manual provided to you.

INSTALLATION INSTRUCTIONS

ADV-X HIGH SPEED METAL DOORS

MODELS 888 AND 889

www.wayne-dalton.com 827802-0001 Rev - 2

TABLE OF CONTENTS

SECTION CONTENTS PAGES

1 SAFETY INFORMATION 3

2 INSTALLATION 4-16

3 FIRST MANUAL DOOR OPERATION 17-18

4 ELECTRONICS 19

5 FINAL INSTALLATION STEPS 20

WARRANTY 21

www.wayne-dalton.com 827802-0001 Rev - 3

In this section and those that follow, the words "DANGER", " WARNING", and "CAUTION" are used to

stress important safety information. The word:

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in injury or

property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

1. Read manual and warnings carefully.

2. All models are equipped with an over current

device. This must be manually reset following

an over current condition.

POTENTIAL

HAZARD EFFECT PREVENTION

MOVING DOOR

WARNING

Can Cause Serious

Injury or Death

Do NOT operate unless the doorway is in sight and free of obstructions. Keep people clear of

opening while door is moving.

Do NOT change control to momentary contact unless an external reversing means is installed.

Do NOT operate a door that jambs.

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

O R O PO RDS

SECTION 1 - SAFETY INFORMATION

High Speed Metal Doors doors are large, heavy objects that move with the help of electric motors. Since

moving objects and electric motors can cause injuries, your safety and the safety of others depends

on you reading the information in this manual. If you have any questions or do NOT understand the

information presented, call technical support at 1-800-764-1457 option 4.

WARNING

www.wayne-dalton.com 827802-0001 Rev - 4

SECTION 2 - INSTALLATION

UNPACKING COMPONENTS

CAUTION

Team lift to avoid injury.

CAUTION

Lift from below with forklift. Do not lift with the

shafts. This could cause damage or personal injury.

CAUTION

Use forklift to avoid injury.

WARNING

Use designated lifting hole and

appropriate lifting equipment to avoid

damage, serious injury, or death.

HEADER

CRATE

GUIDES

CRATE

www.wayne-dalton.com 827802-0001 Rev - 5

SECTION 2 - INSTALLATION

SITE PREPERATION

NOTE: Check that the oor, jamb, and

header are level, square, and plumb. If

they are not, you will need to add shims as

necessary. A laser lever is highly recomended

for this job.

NOTE: Mark the oor in three places to help align

the guides that will be placed in the following step.

www.wayne-dalton.com 827802-0001 Rev - 6

SECTION 2 - INSTALLATION

GUIDE INSTALLATION WARNING

Use designated lifting hole and

appropriate lifting equipment to avoid

damage, serious injury, or death.

NOTE: Guide

covers swing open

on hinges, or can be

lifted o hing pins

and removed to

ease installation.

NOTE: Align guides with marks

on the oor. Check DIM H at three

points. Ensure everything is square,

level, and plumb before anchoring.

NOTE: DIM H is measured from outside of track angle to outside of the opposite track angle.

www.wayne-dalton.com 827802-0001 Rev - 7

NOTE: When using the steel anchoring slots it

may be necessary to temporarily remove the track

for access.

NOTE: Check DIM H at three

points. Ensure everything

is square, level, and plumb

before and after anchoring.

Extra time spent at this

point of the installation may

prevent time consuming

rework.

SECTION 2 - INSTALLATION

GUIDE INSTALLATION

www.wayne-dalton.com 827802-0001 Rev - 8

SECTION 2 - INSTALLATION

HEADER ASSEMBLY INSTALLATION

WARNING

Use appropriate lifting

equipment to avoid

serious injury, or death.

ALLATION

www.wayne-dalton.com 827802-0001 Rev - 9

SECTION 2 - INSTALLATION

SIDE PLATE INSTALLATION

CAUTION

Team lift to avoid injury.

NOTE: Only loosly install side plate

bolts. You will need some movement in

the side plate to complete the next step.

www.wayne-dalton.com 827802-0001 Rev - 10

SECTION 2 - INSTALLATION

IDLER PULLY INSTALLATION

NOTE: Check alignment of pulleys and tighten

set screws in set collars and bearings to prevent

excessive wear on the belts.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wayne-Dalton Garagentoröffner Handbücher

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 6600 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 7400 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9100 Technisches Dokument

Wayne-Dalton

Wayne-Dalton 9100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton Optimal Installationsanleitung

Wayne-Dalton

Wayne-Dalton 9600 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton Torquemaster Plus Kurzanleitung

Wayne-Dalton

Wayne-Dalton TORQUEMASTER 5140 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 464 Kurzanleitung

Wayne-Dalton

Wayne-Dalton idrive pro 3790 Kurzanleitung

Wayne-Dalton

Wayne-Dalton TORQUEMASTER 6100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 800 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 9800 Kurzanleitung

Wayne-Dalton

Wayne-Dalton Torquemaster Plus 8000 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton TorqueMaster Plus 9800 Kurzanleitung

Wayne-Dalton

Wayne-Dalton Prodrive 3220C Kurzanleitung

Wayne-Dalton

Wayne-Dalton TOROQUEMASTER PLUS Kurzanleitung

Wayne-Dalton

Wayne-Dalton Quantum 3214 Kurzanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung