WWW.WEBER.COM 7
16 WWW.WEBER.COM
BURNER IGNITION & USAGE
Summary lighting instructions are on the
instruction tag (Q 1000, Q 1200) or the right
fold-out table (Q 2000, Q2200).
METHODS OF BURNER
IGNITION
There are two ways to ignite
the burner. The first is by using
the ignition system built into
your barbecue. The second is
with a match.
Next are the steps for
igniting your barbecue using
the ignition system. On the
following page are steps for
igniting your barbecue with a
match.
BURNER IGNITION
A) Open the barbecue lid (1).
m DANGER
Failure to open the lid before igniting the
barbecue’s burner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) Unfold the side tables(2) (Q 2000™, Q 2200™).
C) Make sure the burner control knob is turned to the o
() position(3). Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Push burner control knob in and turn it
counterclockwise to start/high ( ) position (4).
F1) Push the red igniter button several times, so it clicks
each time (5) (Q 1000™, Q 2000™).
OR
F2) Push and hold in the electronic igniter button (6)
(Q 1200™, Q 2200™). You will hear the igniter clicking.
G) Check that the burner is lit by looking through the
cooking grills. You should see a flame.
m WARNING: Do not lean over the open
barbecue while igniting.
m WARNING: If burner fails to ignite within
five seconds, stop, turn the burner control
knob to o and wait five minutes to allow
the gas to clear before you try again or
light with a match.
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to the o
() position.
m CAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
4
6
5
Some batteries have a plastic
protective wrap around them.
This plastic must be removed
before you attempt to ignite
your barbecue. Do not confuse
this plastic with the battery
label.
model lighting
instructions
document
use these illustrations
if work
BURNER IGNITION & USAGE
A) Open the barbecue lid (1) and unfold sidetables if
applicable (2).
BURNER IGNITION - Getting started
BURNER IGNITION - Ignition system BURNER IGNITION - Lighting with a match
Depress the RESET button (illuminated red) continuously
for ve (5) seconds to reset the Flame iQ (red light will go
out). Repeat the ignition steps as above.
RESETTING THE Flame iQ AFTER FLAME
FAILURE AND LOCKOUT
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to
the OFF (O) position. Depress the ON/OFF button on the
Flame iQ control box to switch off the Flame iQ.
F) Strike a match and put the ame under the matchlight
hole (5). While holding the lit match, push burner control
knob in and turn it counter clockwise to start/high ( )
position (6).
16 WWW.WEBER.COM
BURNER IGNITION & USAGE
Summary lighting instructions are on the
instruction tag(Q 1000, Q 1200) or the right
METHODS OF BURNER
IGNITION
There are two ways to ignite
the burner. The first is by using
the ignition system built into
your barbecue. The second is
with a match.
Next are the steps for
igniting your barbecue using
the ignition system. On the
following page are steps for
igniting your barbecue with a
match.
BURNER IGNITION
A) Open the barbecue lid (1).
mDANGER
Failure to open the lidbeforeigniting the
barbecue’sburner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) (2) (Q 2000 ™,Q 2200™).
C) Make sure the burner control knob is turned to t
((3) . Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Push burner control knob in and turn it
counterclockwise to start/high ( ) position (4) .
F1) Push the red igniter button several times, so it clicks
each time (5) (Q 1000 ™, Q 2000 ™).
OR
F2) Push and hold in the electronic igniter button (6)
(Q 1200 ™, Q 2200 ™). You will hear the igniter clicking.
G) Check that the burner is lit by looking through the
cooking grills . You should see a flame.
mWARNING: Do not lean over the open
barbecue while igniting.
mWARNING: If burner fails to ignite within
five seconds, stop, turn the burner control
the gas to clear before you try again or
light with a match.
TO EXTINGUISH BURNER
( ) position.
mCAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
4
6
5
Some batteries have a plastic
protective wrap around them.
This plastic must be removed
before you attempt to ignite
your barbecue . Do not confuse
this plastic with the battery
label.
model lighting
instructions
document
use these illustrations
if work
6
16 WWW.WEBER.COM
BURNER IGNITION & USAGE
Summary lighting instructions are on the
instruction tag(Q 1000, Q 1200) or the right
METHODS OF BURNER
IGNITION
There are two ways to ignite
the burner. The first is by using
the ignition system built into
your barbecue. The second is
with a match.
Next are the steps for
igniting your barbecue using
the ignition system. On the
following page are steps for
igniting your barbecue with a
match.
BURNER IGNITION
A) Open the barbecue lid (1).
mDANGER
Failure to open the lidbeforeigniting the
barbecue’sburner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) (2) (Q 2000 ™,Q 2200™).
C) Make sure the burner control knob is turned to t
((3) . Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Push burner control knob in and turn it
counterclockwise to start/high ( ) position (4).
F1) Push the red igniter button several times, so it clicks
each time (5) (Q 1000 ™, Q 2000 ™).
OR
F2) Push and hold in the electronic igniter button (6)
(Q 1200 ™, Q 2200 ™). You will hear the igniter clicking.
G) Check that the burner is lit by looking through the
cooking grills . You should see a flame.
mWARNING: Do not lean over the open
barbecue while igniting.
mWARNING: If burner fails to ignite within
five seconds, stop, turn the burner control
the gas to clear before you try again or
light with a match.
TO EXTINGUISH BURNER
( ) position.
mCAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
4
6
5
Some batteries have a plastic
protective wrap around them.
This plastic must be removed
before you attempt to ignite
your barbecue . Do not confuse
this plastic with the battery
label.
model lighting
instructions
document
use these illustrations
if work
7
16 WWW.WEBER.COM
BURNER IGNITION & USAGE
Summary lighting instructions are on the
instruction tag (Q 1000, Q 1200) or the right
fold-out table (Q 2000, Q2200).
METHODS OF BURNER
IGNITION
There are two ways to ignite
the burner. The first is by using
the ignition system built into
your barbecue. The second is
with a match.
Next are the steps for
igniting your barbecue using
the ignition system. On the
following page are steps for
igniting your barbecue with a
match.
BURNER IGNITION
A) Open the barbecue lid (1).
m DANGER
Failure to open the lid before igniting the
barbecue’s burner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) Unfold the side tables(2) (Q 2000™, Q 2200™).
C) Make sure the burner control knob is turned to the o
() position(3). Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Push burner control knob in and turn it
counterclockwise to start/high ( ) position (4).
F1) Push the red igniter button several times, so it clicks
each time (5) (Q 1000™, Q 2000™).
OR
F2) Push and hold in the electronic igniter button (6)
(Q 1200™, Q 2200™). You will hear the igniter clicking.
G) Check that the burner is lit by looking through the
cooking grills. You should see a flame.
m WARNING: Do not lean over the open
barbecue while igniting.
m WARNING: If burner fails to ignite within
five seconds, stop, turn the burner control
knob to o and wait five minutes to allow
the gas to clear before you try again or
light with a match.
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to the o
( ) position.
m CAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
4
6
5
Some batteries have a plastic
protective wrap around them.
This plastic must be removed
before you attempt to ignite
your barbecue. Do not confuse
this plastic with the battery
label.
model lighting
instructions
document
use these illustrations
if work
WWW.WEBER.COM 17
BURNER IGNITION & USAGE
BURNER IGNITION –
Lighting with a Match
A) Open the barbecue lid (1).
m DANGER
Failure to open the lid before igniting the
barbecue’s burner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) Unfold the side tables(2) (Q 2000™, Q 2200™).
C) Make sure the burner control knob is turned to the o
() position(3). Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Strike a match and put the flame under the matchlight
hole (4). While holding lit match, push burner control
knob in and turn it counterclockwise to start/high ( )
position (5).
F) Check that the burner is lit by looking through the
cooking grills (6). You should see a flame.
m WARNING: Do not lean over the open
barbecue while igniting. Keep your face
and body at least 30 cm (12 in) away
from the matchlight hole when lighting
thebarbecue.
m WARNING: If the burner fails to ignite
within five seconds, stop, turn the burner
control knob to o and wait five minutes
to allow the gas to clear before you try
again.
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to the o
() position.
m CAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
5
6
WWW.WEBER.COM 17
BURNER IGNITION & USAGE
BURNER IGNITION –
Lighting with a Match
A) Open the barbecue lid (1).
m DANGER
Failure to open the lid before igniting the
barbecue’s burner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) Unfold the side tables(2) (Q 2000™, Q 2200™).
C) Make sure the burner control knob is turned to the o
() position(3). Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Strike a match and put the flame under the matchlight
hole (4). While holding lit match, push burner control
knob in and turn it counterclockwise to start/high ( )
position (5).
F) Check that the burner is lit by looking through the
cooking grills (6). You should see a flame.
m WARNING: Do not lean over the open
barbecue while igniting. Keep your face
and body at least 30 cm (12 in) away
from the matchlight hole when lighting
thebarbecue.
m WARNING: If the burner fails to ignite
within five seconds, stop, turn the burner
control knob to o and wait five minutes
to allow the gas to clear before you try
again.
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to the o
() position.
m CAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
5
4
5
DANGER: Failure to open the lid before igniting the
barbecue’s burner, or not waiting ve minutes to
allow the gas to clear if the barbecue does not light,
may result in an explosive are-up which can cause
serious bodily injury or death.
B) Make sure the burner control knob is turned to the OFF
(O) position (3). Check by pushing burner control knob in
and turning it clockwise until it stops.
C) Ensure that the Flame iQ has power (either by way of
12 V or 240 V) and the power supply is switched on.
D) Turn gas supply on at source.
E) Depress the ON/OFF button on the Flame iQ control
box– the button will illuminate green (4).
Note: You have 30 seconds to ignite the barbecue from
when you press the Flame iQ ON button. Should the
barbecue not ignite within the 30 seconds the Flame iQ
will go into lockout and need to be reset.
F) Push the burner control knob in and turn it counter
clockwise to start/high ( ) position (5).
G1) Push the red igniter button several times, so it clicks
each time (6) (Q1000)
G2) Push and hold in the electronic igniter button ( ) (7)
(Q1200). You will hear the igniter clicking.
OR,
H) Once ame is detected, the blue light on the Flame iQ
control box illuminates (8).
I) After ignition close the barbecue lid to enable
pre-heating to commence.
G) Once ame is detected, the blue light on the Flame iQ
control box illuminates (7).
H) After ignition close the barbecue lid to enable
pre-heating to commence.
ON/OFF
4
8
7
RESET
Hold for
5 seconds
There are two ways to ignite the burner. The
rst is by using the ignition system built into
your barbecue. The second is with a match.
METHODS OF BURNER IGNITION
Flame iQ Q1000 & Q1200
Summary lighting instructions are on the
instruction tag of your barbecue and Flame iQ.
Only use this method if your ignition system is not
working.
