weBoost DRIVE 4G-X FLEET Bedienungsanleitung
User Manual
PROFESSIONAL VEHICLE CELLULAR
SIGNAL BOOSTER KIT
DRIVE 4G-X FLEET
A WILSON ELECTRONICS BRAND
NEED HELP? solidsignal.com 877.312.4547
______
Index
Package Contents
1
STEP 1: Mount Outside Antenna & Route Cable
2
STEP 2: Mount Inside Antenna
6
STEP 3: Wiring The Power Supply To Vehicle Battery
7
STEP 4: Connect Coax Cables To Booster
8
STEP 5: Connect Power Supply To Booster
9
Light Patterns
10
Troubleshooting
11
Safety Guidelines
12
Specifications
13
Warranty
14
DRIVE 4G-X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 1
________
Package
Contents
Drive 4G-X
Booster
& Bracket
Outside NMO
Antenna +
Connector
Mounting Cable
4G In-Vehicle
Antenna
Power
Supply
Optional
Cable
Protective
Tape For
Installation
2PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE 4G-X FLEET
______
Step 1: Mount Outside
Antenna & Route Cable
Identify a location on the top of your vehicle that is:
Near the center of the roof
At least 12 inches away from any other antennas
At least 6 inches away from any windows
(for best performance install on top of vehicle)
Mount the outside antenna by placing on top
of vehicle.
6 in. away from windows
(including sunroofs) NMO Outside Antenna
Placement
NOTE: Drill and 3/4” hole saw drill bit required.
WARNING: With this option, we recommend doing a ‘soft install’
before drilling the hole. Set up the system by routing the
cable through an open door or window, completing the setup
instructions, verifying the system works as desired, and then
drilling the hole.
DRIVE 4G-X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 3
Once you have determined the
best location for the antenna,
place the Protective Tape on the
vehicle in the desired location.
Using a 3/4” hole saw, drill hole in
the center of the protective tape.
After hole has been drilled,
insert NMO Mounting
Cable through (SMA
connector end first) and
remove collar.
______
(STEP 1 cont.)
See diagrams below for NMO Outside Antenna installation.
remove
collar
insert
through
hole
Protective Tape
vehicle surface
Protective Tape
3/4” bit
4PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE 4G-X FLEET
______
(STEP 1 cont.)
Position threads of the cable mount above vehicle surface.
Apply included silicone grease to the o-ring on the collar
then screw the collar to the base mount. Ensure the mount is
centered in the hole and tighten with wrench.
Before attaching the antenna, clean the area around the
mount. Apply a thin layer of silicone grease to the threads,
only, of the NMO mount and to the o-ring on the antenna.
DO NOT apply to the antenna pin contact surface. Screw the
antenna onto the NMO mount and hand tighten into place.
Ensure the antenna is screwed all the way in and make sure
the casket is touching the vehicle surface.
apply silicone
grease
hand tighten
screw on
NMO Antenna
screw collar
to base mount
DRIVE 4G-X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 5
______
(STEP 1 cont.)
For a professional installation we recommend routing the
cable under the headliner and down through the side trim
panel to the desired booster location on the floor of the
vehicle.
side trim panel
headliner
r
u
n
c
a
b
l
e
f
r
o
m
N
M
O
O
u
t
s
i
d
e
A
n
t
e
n
n
a
t
o
b
o
o
s
t
e
r
Route NMO Outside Antenna cable inside the vehicle.
6PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE 4G-X FLEET
The location should be at least 18 inches but no more than 36
inches from where the cellular device will be used. Adhesive
and Velcro® mounting options are included.
In-Vehicle
Antenna
In
In
n-
-
V
Veh
i
c
A
An
Ant
enn
In-Vehicle Antenna
Identify a place to mount the 4G In-Vehicle Antenna, either
on the side of the seat or on the dash and mount.
______
Step 2: Mount Inside Antenna
clean surface of dash
before attaching
adhesive strip
dash option
seat option
DRIVE 4G-X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 7
Before connecting the power supply, disconnect the vehicle battery
leads to avoid any electrical shocks during installation.
Locate a place where cables are already running through the firewall
(rear wall of engine bay) to the inside of the cabin.
Locate the same firewall hole from step 2 in the inside of the vehicle
cabin.
Route the power cables of the power supply from the inside of the
vehicle cabin out through firewall hole from steps 2 & 3.
Note: The cables must be routed inside to outside since the power
supply brick won’t fit through the firewall holes. The power supply
brick should remain inside the vehicle cabin.
Connect the positive lead of the power supply (lead with red tape)
to the disconnected positive (+) lead of the battery (not the positive
terminal on the battery itself).
Connect the negative lead of the power supply (lead without tape)
to the disconnected negative (-) lead of the battery (not the negative
terminal on the battery itself).
Connect the positive (+) lead back to the vehicle battery.
Connect the negative (-) lead back to the vehicle battery.
Use steps below as a draft/template of the general install of
the power supply.
______
Step 3: Wiring The Power
Supply To Vehicle Battery
1
2
3
4
5
6
7
8
NOTE: Having the power supply directly connected to the battery may
drain the battery’s life. Please review the vehicle’s owner’s manual for more
information. Adding a “fuse tap” may be another solution. A “fuse tap” is an
electrical part that functions as a power splitter and is meant to be installed
in the car’s fuse box, making the amp shut o when the vehicle’s ignition
switch is turned o.
8PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE 4G-X FLEET
______
Step 4: Connect Coax Cables
To Booster
Connect the cable from the NMO Outside Antenna to the port
labeled “Outside Antenna” on the Drive 4G-X booster.
Connect the cable from the 4G In-Vehicle Antenna to the port
labeled “Inside Antenna” on the booster.
from NMO Outside Antenna
from Inside Antenna
NOTE: Bracket can be used to fasten booster in a specific location if desired.
Andere Handbücher für DRIVE 4G-X FLEET
8
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere weBoost Extender Handbücher
weBoost
weBoost Drive 3G-M+ Bedienungsanleitung
weBoost
weBoost Drive 3G-Flex 470013 Bedienungsanleitung
weBoost
weBoost Drive AM100-Pro Bedienungsanleitung
weBoost
weBoost Home-4G 470001 Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X RV Bedienungsanleitung
weBoost
weBoost Drive Reach Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X OTR 470210R Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X FLEET Bedienungsanleitung
weBoost
weBoost DRIVE SLEEK OTR Bedienungsanleitung
weBoost
weBoost Home MultiRoom Bedienungsanleitung
weBoost
weBoost Destination RV Bedienungsanleitung
weBoost
weBoost Home Room U530001 Bedienungsanleitung
weBoost
weBoost DRIVE 3G-S Bedienungsanleitung
weBoost
weBoost eqo Bedienungsanleitung
weBoost
weBoost Home Room Bedienungsanleitung
weBoost
weBoost Home 4G Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X OTR Bedienungsanleitung
weBoost
weBoost Drive Reach OTR Bedienungsanleitung
weBoost
weBoost Drive Reach RV Bedienungsanleitung
weBoost
weBoost 470113 Bedienungsanleitung
