weBoost DRIVE X FLEET Bedienungsanleitung
PROFESSIONAL VEHICLE CELL
SIGNAL BOOSTER KIT
DRIVE X FLEET
A WILSON ELECTRONICS BRAND
NEED HELP? support.weboost.com
Use our weBoost App to guide you through the installation.
See inside page for more details.
1-866-294-1660
Installation Guide
Download the weBoost App
Use our app to guide you through setting up a weBoost cell phone
signal booster in your home, business, or vehicle. Boost every
network, including 5G, right away.
Download the weBoost App
Videos to guide you
through installation
Antenna positioning guide
for optimal performance
Before and after cell
signal readings
______
Index
Package Contents 1
STEP 1: Drill Cable Entry Hole To Your Vehicle 2
STEP 2: Mount NMO Outside Antenna 5
STEP 3: Mount In-Vehicle Antenna 6
STEP 4: Wire The Power Supply 7
STEP 5: Connect Coax Cables To Booster 8
STEP 6: Connect Power Supply To Booster 9
Light Patterns 10
Troubleshooting 11
Safety Guidelines 13
Specifications 14
Warranty 15
1PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET
________
Package
Contents
Drive X
Booster
& Bracket
Outside NMO
Antenna +
Connector
Mounting Cable
In-Vehicle
Antenna Power
Supply
Optional Antenna
Extension Cable Protective Tape
For Installation O-Ring Lubricant
Packet
DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 2
______
Step 1: Drill Cable Entry Hole
To Your Vehicle
Identify a location for NMO outside antenna on the
top of your vehicle that is:
Near the center of the roof
At least 12 inches away from any other antennas
At least 12 inches away from any windows
(for best performance install on top of vehicle)
Do a ‘soft install’ before drilling the hole for the
cable entry.
Set up the system by routing the cable through
an open door or window, completing the setup
instructions, verifying the system works as desired,
and then drilling the hole.
12 in. away from windows
(including sunroofs)
Good NMO Outside
Antenna Placement
3PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET
Place the protective tape on the
vehicle in the desired location.
Using a 3/4” hole saw, drill a
hole in the center of the
protective tape.
______
(STEP 1 cont.)
After completing the ‘soft install’ and identifying NMO
outside antenna location:
protective tape
vehicle surface
protective tape
3/4” bit
DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 4
apply silicone grease
apply silicone grease
After hole has been drilled, insert NMO Mounting Cable
through (SMA connector end first) and remove collar.
Position threads of the cable mount above vehicle surface.
Apply included silicone grease to the o-ring on the collar
then screw the collar to the base mount. Ensure the mount is
centered in the hole and tighten with wrench.
screw collar
to base mount
For a professional installation, we recommend routing the cable
under the headliner and down through the side trim panel to
the desired booster location on the floor of the vehicle.
side trim panel
headliner
r
u
n
c
a
b
l
e
f
r
o
m
N
M
O
O
u
t
s
i
d
e
A
n
t
e
n
n
a
t
o
b
o
o
s
t
e
r
remove
collar
insert through hole
______
(STEP 1 cont.)
5PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET
Before attaching the antenna, apply a thin layer of silicone
grease to the threads, only, to the NMO mount and to the
o-ring on the antenna. Screw the antenna onto the NMO
mount and hand tighten into place.
hand tighten and make sure
gasket is touching vehicle
surface
screw on
NMO Antenna
______
Step 2: Mount NMO
Outside Antenna
apply silicone grease
apply silicone grease
NOTE: DO NOT apply silicone grease to the antenna pin contact surface.
DRIVE X FLEET PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT 6
The location should be at least 18 inches but no more than
36 inches from where the cell phone device will be used.
Adhesive and Velcro® mounting options are included.
In-Vehicle Antenna
Identify a place to mount the in-vehicle antenna, either on
the side of the seat or on the dash and mount.
______
Step 3: Mount In-Vehicle
Antenna
clean surface of dash before attaching
adhesive strip
dash option
seat option
In-Vehicle
Antenna
7PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT DRIVE X FLEET
Before connecting the power supply, disconnect the vehicle battery
leads to avoid any electrical shocks during installation.
Locate a place where cables are already running through the firewall
(rear wall of engine bay) to the inside of the cabin.
Locate the same firewall hole from inside of the vehicle cabin.
Route the power cables of the power supply from the inside of the
vehicle cabin out through firewall hole.
Note: The cables must be routed inside to outside since the power
supply brick won’t fit through the firewall holes. The power supply
brick should remain inside the vehicle cabin.
Connect the positive lead of the power supply (lead with red tape)
to the disconnected positive (+) lead of the battery (not the positive
terminal on the battery itself).
Connect the negative lead of the power supply (lead without tape)
to the disconnected negative (-) lead of the battery (not the negative
terminal on the battery itself).
Connect the positive (+) lead back to the vehicle battery.
Connect the negative (-) lead back to the vehicle battery.
Use steps below as a draft/template of the general install of
the power supply.
______
Step 4: Wire The Power
Supply
1
2
3
4
5
6
7
8
NOTE: Having the power supply directly connected to the battery may
drain the battery’s life. Please review the vehicle’s owner’s manual for more
information. Adding a “fuse tap” may be another solution. A “fuse tap” is an
electrical part that functions as a power splitter and is meant to be installed
in the car’s fuse box, making the amp shut o when the vehicle’s ignition
switch is turned o.
Inhaltsverzeichnis
Andere weBoost Extender Handbücher
weBoost
weBoost DRIVE X RV Bedienungsanleitung
weBoost
weBoost DRIVE 3G-S Bedienungsanleitung
weBoost
weBoost 470001 Bedienungsanleitung
weBoost
weBoost Home 4G Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X FLEET Bedienungsanleitung
weBoost
weBoost Home 3G Bedienungsanleitung
weBoost
weBoost SIGNAL 3G Bedienungsanleitung
weBoost
weBoost 460059 Bedienungsanleitung
weBoost
weBoost drive 3G-M Bedienungsanleitung
weBoost
weBoost ego Bedienungsanleitung
weBoost
weBoost DRIVE 3G-S Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X FLEET Bedienungsanleitung
weBoost
weBoost Connect RV 65 Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X FLEET Bedienungsanleitung
weBoost
weBoost 470019 Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X FLEET Bedienungsanleitung
weBoost
weBoost Home Room 460020 Bedienungsanleitung
weBoost
weBoost Home 3G Bedienungsanleitung
weBoost
weBoost Basic Home Bedienungsanleitung
weBoost
weBoost DRIVE 4G-X RV Bedienungsanleitung
