WEG DeviceNet CFW500 Kurzanleitung

PROFIBUS DP

Communication Plug-in

Module

Módulo Plug-in de

Comunicación PROFIBUS DP

Módulo Plug-in de

Comunicação PROFIBUS DP

CFW500

Installation, Conﬁguration and Operation Guide

Guía de Instalación, Conﬁguración y Operación

Guia de Instalação, Conﬁguração e Operação

Motors | Automation | Energy | Transmission & Distribution | Coatings

Summary / Índice

English

EspañolPortuguês

ÍNDICE

1 SAFETY INFORMATION...............................5

1.1 SAFETY WARNINGS ...................................5

1.2 PRELIMINARY RECOMMENDATIONS.......5

2 GENERAL INFORMATION...........................5

3 CONTENTS OF THE PACKAGE .................5

4 ACCESSORY INSTALLATION ....................6

5 SETTINGS......................................................6

APPENDIX A – FIGURES...............................23

ÍNDICE

1 INFORMACIONES DE SEGURIDAD ........11

1.1 AVISOS DE SEGURIDAD ...........................11

1.2 RECOMENDACIONES PRELIMINARES... 11

2 INFORMACIONES GENERALES...............11

3 CONTENIDO DEL EMBALAJE ................11

4 INSTALACIÓN DEL ACCESORIO .............12

5 CONFIGURACIONES..................................12

ANEXO A – FIGURAS.....................................23

ÍNDICE

1 INFORMAÇÕES DE SEGURANÇA............17

1.1 AVISOS DE SEGURANÇA ........................17

1.2 RECOMENDAÇÕES PRELIMINARES....... 17

2 INFORMAÇÕES GERAIS ...........................17

3 CONTEÚDO DA EMBALAGEM..................17

4 INSTALAÇÃO DO ACESSÓRIO .................18

5 CONFIGURAÇÕES......................................18

ANEXO A – FIGURAS.....................................23

PROFIBUS DP Communication Plug-in Module

English

CFW500 | 5

1 SAFETY INFORMATION

1.1 SAFETY WARNINGS

NOTE!

Only use the PROFIBUS DP communication

plug-in module (CFW500-CPDP or

CFW500-CPDP2) on WEG inverters of the

CFW500 line.

Read the user’s manual of the CFW500

and the user’s manual of the PROFIBUS

DP before installing or operating this

accessor y.

This guide contains important information

for the correct understanding and proper

operation of this module.

1.2 PRELIMINARY RECOMMENDATIONS

ATTENTION!

Always disconnect the general power

supply before connecting or disconnecting

the accessories of the frequency inverter

CFW500.

Wait for at least 10 minutes to guarantee

complete de-energization of the inverter.

2 GENERAL INFORMATION

This guide contains instructions for the installation,

configuration and operation of the PROFIBUS DP

communication plug-in module (CFW500-CPDP or

CFW500-CPDP2).

3 CONTENTS OF THE PACKAGE

When receiving the product, check if this package

contains:

Accessory in anti-static packaging.

Installation, configuration and operation guide.

PROFIBUS DP Communication Plug-in Module

English

6 | CFW500

4 ACCESSORY INSTALLATION

The accessory is easily installed or replaced. For correct

installation of the accessory execute the following steps:

Step 1: With the inverter de-energized, remove the front

cover of the Inverter (figure A.1 (a)).

Step 2: Remove, if present, the accessory (connected

plug-in module) according to figure A.1 (a).

Step 3: Fit and press the accessory to be installed as

indicated in figure A.1 (b) and then assemble the front

cover of the inverter.

Step 4: Power up the inverter and check if parameter

P0027 shows value 8 (P0027 = 8). If this information is not

true, check if the module used is actually the CFW500-

CPDP or CFW500-CPDP2 and repeat steps 1-4.

5 SETTINGS

The control connections (analogical input / output, digital

inputs / outputs and RS485 interface) must be performed

as shown in table 1 for the CFW500-CPDP Module or in

table 2 for the CFW500-CPDP2 Module.

PROFIBUS DP Communication Plug-in Module

English

CFW500 | 7

Table 1: Signals of control connector - CFW500-CPDP

module

Connector Description

Top Connection

1DI1 Digital input 1

3DI2 Digital input 2

5+24 V +24 Vdc power supply

7DO1-RL-NO Digital output 1

(NO contact of relay 1)

9DO1-RL-C Digital output 1

(common point of relay 1)

11 DO1-RL-NC Digital output 1

(NC contact of relay 1)

Bottom Connection

2AO1 Analogical output 1

4AI1 Analogical input 1

6DO2-TR Digital output 2 (Transistor)

8 RS485 – A (-) RS485 (Terminal A- )

10 RS485 – B (+) RS485 (Terminal B+ )

12 GND Reference 0 V

Table 2: Signals of control connector - CFW500-CPDP2

module

Connector Description

Top Connection

1DI1 Digital input 1

3DI2 Digital input 2

5+24 V +24 Vdc power supply

7DO1-RL-NO Digital output 1

(NO contact of relay 1)

9DO1-RL-C Digital output 1

(common point of relay 1)

11 DO1-RL-NC Digital output 1

(Contato NC do Relé 1)

13 A- RxD/TxD negative (green)

15 B+ RxD/TxD positive (red)

Bottom Connection

2AO1 Analogical output 1

4AI1 Analogical input 1

6DO2-TR Digital output 2 (Transistor)

8 RS485 – A (-) RS485 (Terminal A- )

10 RS485 – B (+) RS485 (Terminal B+ )

12 GND Reference 0 V

14 GND Reference 0 V

16 SHIELD Proﬁbus DP cable shield

PROFIBUS DP Communication Plug-in Module

English

8 | CFW500

DI1

DI2

GND

DO1-RL-NO

RS485 - A

+24 V

DO1-RL-C

RS485 - B

DO1-RL-NC

GND

AO1

AI1

DO2-TR R

rpm

+24 V

(a) Signals of the control connector for CFW500-CPDP

module

PROFIBUS DP Communication Plug-in Module

English

CFW500 | 9

DI1

DI2

GND

DO1-RL-NO

RS485 - A

+24 V

A-

B+

DO1-RL-C

RS485 - B

DO1-RL-NC

GND

SHIELD

AO1

AI1

DO2-TR R

rpm

+24 V

(b) Signals of the control connector for CFW500-CPDP2

module

Figure 1: (a) and (b) Signals of the control connector

Table 3: Signals of the PROFIBUS DP communication

connector - available in CFW500-CPDP module

DB-9

GND

RTS

B+

N.C

A-

N.C

+5 V

1N.C

2N.C

3B (+)

4RTS

5GND

6 + 5 V

7N.C

8A (-)

9N.C

PROFIBUS DP Communication Plug-in Module

English

10 | CFW500

The location of the DIP-switches to select the kind of the

analog input and output signal and the termination of the

RS485 and PROFIBUS DP network can be better viewed

in figure A.2. To use the analog inputs and/or outputs with

signal in current, switch S1 and related parameters must

be set as indicated in table 4. For further details about

the control connections see chapter 3 Installation and

Connection of the CFW500 user's manual.

Table 4: Configurations of the switches to select the

kind of signal at the analog input and output on the

CFW500-CPDP / CFW500-CPDP2

Input/

Output Signal Setting of

Switch S1

Range of

Signal

Parameter

Settings

AI1

Voltage S1.1 = OFF 0...10 V P0233 = 0 or 2

Current S1.1 = ON 0...20 mA P0233 = 0 or 2

4...20 mA P0233 = 1 or 3

AO1

Voltage S1.2 = ON 0...10 V P0253 = 0 or 3

Current S1.2 = OFF 0...20 mA P0253 = 1 or 4

4...20 mA P0253 = 2 or 5

Table 5: Configurations of the switches for RS485 and

PROFIBUS DP communication

Communication Switch Switch Setting Option

RS485 S1(*)

S1.3 = OFF and

S1.4 = OFF

RS485

termination OFF

S1.3 = ON and

S1.4 = ON

RS485

termination ON

PROFIBUS DP S2(*)

S2.1 = OFF and

S2.2 = OFF

PROFIBUS DP

termination

resistor inactive

S2.1 = ON and

S2.2 = ON

PROFIBUS DP

termination

resistor active

(*) No other combinations of the switches are allowed.

This module has a connector (figure A.2) used by the

CFW500-MMF Flash Memory Module, which allows

data transfer between inverters. For further details on

this accessory, refer to the installation and operation

guide of the CFW500-MMF.

Andere Handbücher für DeviceNet CFW500

Inhaltsverzeichnis

Sprachen:

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung