Weintek CMT-3103 Bedienungsanleitung

User

Manual

cMT-3103 Wireless Network Settings Guide

Weintek USA, Inc.

www.WeintekUSA.com

(425) 488-1100

Rev. JAN 22 2019

Table of Contents

1. Introduction………………………………………………………………………………………………………………………….. 3

2. Wireless Connection Setup via Touch Screen………………………………………………………………………… 4

3. Wireless Connection Setup via Web Interface……...................................................................... 7

4. System Registers…………………………………………............................................................................... 10

1. Introduction

cMT-3103 HMI has wireless connectivity that allows users to connect to a local wireless access point via Wi-

Fi. It supports the following frequency bands, IEEE802.11b, IEEE802.11g, and IEEE802.11n. cMT-3103 HMI is

equipped with one independent Ethernet port which isolates the device network from the company/factory

network. Wireless connection is WAN (Wide Area Network) which is allowed to connect to a public network

or another network via a gateway. LAN is Local Area Network port.

Connect cMT-3103 HMI to a router by wireless connection as the diagram shows below.

The default IP address of WiFi is DHCP. The default IP address of LAN is DHCP. The IP addresses of WiFi and

LAN must be configured to the different subnets

LAN

2. Wireless Connection Setup via Touch Screen

Press the system toolbar button at the upper left of the screen to open Setup.

This page shows general information about cMT-3103 HMI and network information.

To access Wi-Fi settings, click on the lock icon at the top left corner. There are two different levels of password

protection. Select [System Setting] and enter System Setting password. The default password of System

Setting is 111111.

After clicking on [OK], the icon will become unlocked.

Wi-Fi-

Go to [Wi-Fi] tab and enable [Wi-Fi Radio]. Scroll up and down to select an access point and enter its

password. Once the wireless connection succeeds, the status will display “Connected.”

Name

Descriptions

Wi-Fi Radio

Turn Wi-Fi radio ON or OFF.

Status

It shows one of the statuses including Stopped, Connecting,

Retrying, or Connected.

Access Point List

A list of currently available access points.

Refresh

It can refresh the Access Points list.

Join other(SSID)

It allows users to manually add an access point and connect with.

SSID

SSID name of the wireless access point to connect with.

Password

Enter the password. The password can either be visible or invisible

when entering the password.

Connect/Disconnect

Connect or disconnect from a wireless router.

The signal strength is classified into four levels: Excellent, Good, Fair, and Weak, as shown below.

You can tap the blue information icon to open the setting page of the access point. Then, set the IP address

to static IP. The IP addresses of WiFi and LAN must be on the separate subnets. Click [OK] to confirm the

setting.

Network-

Set the IP address of LAN port on the Network tab. The default IP address of LAN port is DHCP. You can set

the IP address to static IP. The IP addresses of WiFi and LAN must be on the separate subnets. After making

changes on the setting, click [OK] to confirm.

3. Wireless Connection Setup via Web Interface

Configuring wireless connection of the cMT-3103 HMI via a web browser is available. Before configuration,

connect cMT-3103 HMI (LAN) to a router via an Ethernet cable. Open a web browser (IE, Chrome, or Firefox)

and enter the IP address of the cMT-3103 HMI. For example, enter 192.168.1.15.

Select an identity and enter its password.

Go to [Wi-Fi] tab, the way to set up the wireless connection is same as on the HMI screen.

How to Switch the access point to others

Click on the current wireless connection. The popup window will prompt you to disconnect the connection.

Select another access point and enter its password.

How to set the DHCP to static IP

Setting to static IP is available. To use the static IP address, click the blue information icon. Choose [Use

static IP address below] and enter the IP address, mask, gateway IP, and DNS.

[Join other SSID]- You can manually connect the HMI to an access point that is not displayed on the AP list.

Make sure the Wi-Fi signal is strong enough.

3. System Registers

Descriptions

Associated object

Readable/

Writable

LW-11383(16bit)

Wi-Fi control (1:Disconnected, 2:Connect,

3:Popup Wi-Fi setting dialog)

Multi-State Switch

R/W

LW-11384(16bit)

Error code (0:No error, 1:No such device, 2:Wi-Fi

radio is off)

Word Lamp

LW-11385(16bit)

Status (0:Stopped, 1:Connecting, 2:Retrying,

3:Connected)

Word Lamp

LW-11386(16 words)

Connected SSID

ASCII

LW-11402(16bit)

Signal strength level(0:None, 1:Weak, 2:Fair,

3:Good, 4:Excellent) *Note 1

Word Lamp

LW-11403(16bit)

Country code *Note 2

ASCII

R/W

LW-11404(16bit)

Wi-Fi radio (0:Off, 1:On)

Multi-State Switch

R/W

*Note 1: The signal strength is classified into four levels: 1. Weak (<-70 dBm), 2. Fair (-60 ~ -70

dBm), 3. Good (-50 ~ -60 dBm), 4. Excellent (>-50 dBm)

*Note 2: Enter Wi-Fi country code in ASCII for uppercase letters, the setting will take effect

after rebooting HMI. Wireless regulations vary from country to country. The country code

selection affects the list of channels of the wireless radio.

LW-11404

LW-11402

LW-11385

LW-11384

LW-11386

LW-11403

Inhaltsverzeichnis

Andere weintek Aufnahmegeräte Handbücher

weintek

weintek cMT3072X Series Bedienungsanleitung

weintek

weintek MT8000iE Series Bedienungsanleitung

weintek

weintek cMT3072XP Series Bedienungsanleitung

weintek

weintek cMT2158X Series Bedienungsanleitung

weintek

weintek cMT-iPC15 Bedienungsanleitung

weintek

weintek mTV series Bedienungsanleitung

weintek

weintek cMT2108X Series Bedienungsanleitung

weintek

weintek cMT-SVRX Series Bedienungsanleitung

weintek

weintek cMT-SVR Benutzerhandbuch

weintek

weintek cMT3000X Series Benutzerhandbuch

weintek

weintek cMT2078X Series Bedienungsanleitung

weintek

weintek cMT-SVR-200 series Bedienungsanleitung

weintek

weintek cMT3152X Series Bedienungsanleitung

weintek

weintek MT8070iER1 Series Bedienungsanleitung

weintek

weintek cMT2128X Series Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch

weintek cMT-3103 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken