Wen 56035T Bedienungsanleitung

This is a guide to greasing the vibrating assembly for your WEN 56035, 56035T, or 56035M

plate compactor This guide is best used in conjunction with the compactor’s manual, included

as a physical copy with your unit and available on the WEN website page for the plate

compactor (link here ), by clicking “Click here to view the product manual”

If at any point you need assistance, have questions, or want to order parts, call WEN customer

service at 1-847-429-9263, M-F, 8-5 Central Time, or email techsupport@wenproducts com

If replacing any parts, use only genuine replacement parts purchased from WEN Products. Use of replacement

parts not sold by WEN Products will void your warranty and could lead to decreased performance or injury.

ABLE OF CON EN S

Tools needed 1

Removing the vibrating assembly 1

Greasing the vibrating assembly 5

Reassembly 8

OOLS NEEDED

•13, 17, 18, 19, 27mm sockets and ratchet

◦Alternative: combination or adjustable

wrench(es)

•Impact wrench or breaker bar (optional)

•Large flat-head screwdriver

•Torque wrench and appropriate standard

sockets, as well as 5mm and 6mm hex-bit

sockets

•5mm and 6mm hex wrench

•Retaining ring pliers

•Rubber mallet

•Reversible anaerobic threadlocker (e g blue

Loctite ®)

•NLGI #2 EP lithium-based high-temperature

grease, approximately 60 – 70 grams

ENSURE THAT THE ENGINE IS COOL BEFORE BEGINNING ANY MAINTENANCE OR REPAIR WORK FOLLOW

ALL SAFETY PROCEDURES LISTED IN YOUR OWNER’S MANUAL USE COMMON SENSE AVOID INJURY

REMOVING HE VIBRA ING ASSEMBLY

1 Make sure the engine is shut down and fully cooled Drain the engine oil and gasoline according to the

instructions in your owner’s manual

2 Use a 13mm socket and ratchet (or combination wrenches) to remove the mounting bolts on both sides of the

belt cover (Figs 1 & 2)

Fig. 1: Mounting bolt 1. Fig. : Mounting bolt .

Date last modified: 0 3/01/30

3 Remove the belt cover The clutch and belt are now exposed (Fig 3)

4 With the screwdriver shaft positioned on the outside of the clutch, position the tip under the belt, and lever the

belt off the clutch while turning the clutch counterclockwise (Figs 4 & 5)

Fig. 4: Removing the belt (1).

Fig. 5: Removing the belt ( ).

Date last modified: 0 3/01/30

Fig. 3: Clutch and belt.

5 The belt can now be removed from the lower, vibrating assembly pulley (within the plate)

6 Remove the 4 nuts and washers from both sides of the engine support plate (Fig 6)

7 Gently lift the handles, engine assembly, and support plate off the shock absorbers, and carefully set the

assembly to the side

8 Remove the 8 mounting bolts from the exciter seat (Fig 7), then remove the exciter seat and vibrating

assembly from the bottom plate You may need an impact wrench or breaker bar to remove the bolts

Date last modified: 0 3/01/30

Fig. 7: Remove the 8 mounting bolts, then gently remove the exciter seat and vibrating

assembly from the bottom plate.

Fig. 6: Remove these nuts and washers ( each side).

9 Use the 27mm socket and adjustable or combination wrench to remove the two mounting bolts and nuts from

the vibrating assembly (Figs 8 & 9) You may need a breaker bar or impact wrench to remove the nuts and

bolts

Fig. 8: Remove these bolts (top of assembly). Fig. 9: Remove these nuts (bottom of assembly).

10 Remove the old vibrating assembly from the exciter seat (Fig 10)

Date last modified: 0 3/01/30

Fig. 10: Vibrating assembly removed.

GREASING HE VIBRA ING ASSEMBLY

11 Use the 6mm hex wrench to remove the socket-head cap screw and washers from the right side of the

vibrating assembly (Figs 11, 12) It’s a standard right-hand threaded screw (lefty-loosey)

Fig. 11: Use a 6mm hex wrench to remove this screw. Fig. 1 : Screw and washer removed.

12 Slide the pulley off the assembly, as well as the shaft key (Figs 13, 14)

Fig. 13: Pulley removed. Fig. 14: Shaft key removed.

13 Remove the retaining ring and eccentric block (Figs 15 – 17)

Date last modified: 0 3/01/30

Fig. 15: Retaining ring. Fig. 16: Retaining ring removed. Fig. 17: Eccentric block removed.

14 Use the 5mm hex wrench to remove the 3 socket-head cap screws around the bearing cover (Fig 18 – 19)

They are standard right-hand threaded screws (lefty-loosey)

Fig. 18: Remove 3 screws from bearing cover. Fig. 19: Screw removed.

15 Remove the bearing cover and oil seal (brown seal shown around the shaft in Fig 18 above) from the main

body You may need to clamp the main body to the table to do this It is easiest to gently twist the cover and

seal off the shaft; you can also gently use a flat-head screwdriver to help loosen it from the body Be careful

not to damage the bearing cover Once the bearing cover is removed (Fig 20), the bearing is exposed (Fig

21)

Date last modified: 0 3/01/30

Fig. 0: Bearing cover removed. Fig. 1: Bearing exposed.

16 Apply approximately 60 – 70 grams of high-temperature grease to the bearing Pack it in tightly

17 Replace the bearing cover and oil seal Apply some reversible anaerobic threadlocker (e g blue Loctite ®) to

the screw threads, then tighten them in a circular pattern Use the torque wrench to tighten the screws to 8.1

ft-lbs (11 Nm).

18 On the other side of the assembly, remove the retaining ring, eccentric block, and bearing cover and oil seal

(basically, repeat steps 13 – 15) Apply approximately 60 – 70 grams of high-temperature grease to the

bearing Pack it in tightly

19 Replace the bearing cover and oil seal Apply some reversible anaerobic threadlocker (e g blue Loctite ®) to

the screw threads, then tighten them in a circular pattern Use the torque wrench to tighten the screws to 8.1

ft-lbs (11 Nm).

20 Reassemble the eccentric blocks and retaining rings on both sides

21 Replace the pulley and shaft key (step 12)

22 Apply some reversible anaerobic threadlocker (e g blue Loctite ®) to the pulley mounting screw threads, and

use the torque wrench to tighten the pulley mounting screw and washer (step 11) to 19.2 ft-lbs (26 Nm).

23 The vibrating assembly is now fully greased and ready to be reassembled onto the plate compactor

Date last modified: 0 3/01/30

REASSEMBLY

24 Position the vibrating assembly on the exciter seat When reinstalling the mounting nuts and bolts, apply some

reversible anaerobic threadlocker (e g blue Loctite ®) to the bolt threads, and use the torque wrench to

tighten the nuts to 147.5 ft-lbs (200 Nm)

25 Reinstall the exciter seat and vibrating assembly on the bottom plate When reinstalling the mounting bolts,

apply some threadlocker to the bolt threads, and use the torque wrench to tighten the nuts to 60.5 ft-lbs (82

Nm)

26 Reposition the engine assembly and support plate on the shock absorbers Thread the belt through the slot in

the support plate Tip the engine assembly up and install the belt on the clutch pulley (see Fig 4) Tip the

assembly down and use a socket or wrench to tighten the lock nuts removed in step 6

1 TIP: if you’re having trouble using this technique, use the screwdriver technique (step 4 ) to work the belt

back onto the pulley

27 Replace the belt cover and mounting bolts When reinstalling the mounting bolts, apply some threadlocker to

the bolt threads, and use the torque wrench to tighten the bolts to 20.6 ft-lbs (28 Nm)

28 Reinstall the handles and all mounting nuts and bolts Use a socket or wrench to tighten them

29 Make sure all fasteners are fully tightened Start your plate compactor according to the instructions in your

manual

QUES IONS? PROBLEMS?

Contact WEN Customer Service at 1-847-429-9263, M-F, 8-5 CST, or email

techsupport@wenproducts com

Date last modified: 0 3/01/30

Andere Handbücher für 56035T

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wen Vibrationsstampfer und -verdichter Handbücher

Wen

Wen 56040 Bedienungsanleitung

Beliebte Vibrationsstampfer und -verdichter Handbücher anderer Marken

MULTIQUIP

MULTIQUIP Mikasa Series Bedienungsanleitung

Fayat

Fayat Bomag BP 20/50 Bedienungsanleitung

Altrad

Altrad BELLE RTX Bedienungsanleitung

Weber mt

Weber mt CF 1-II Hd Betriebsanleitung

TMG

TMG TMG-PC160K Bedienungsanleitung

swepac

swepac FB 430 Bedienungsanleitung

Weber mt

Weber mt SRV 590-II Betriebsanleitung

Makita

Makita VR001G Bedienungsanleitung

Euro Shatal

Euro Shatal TC63 Bedienungsanleitung

ADENDORFF

ADENDORFF TRE-85 Bedienungsanleitung

Husqvarna

Husqvarna EP 121B Bedienungsanleitung

Technoflex

Technoflex Kangaroo Kn-18GH Leitfaden

MQ Multiquip

MQ Multiquip Mikasa MTR-40HS Leitfaden

MULTIQUIP

MULTIQUIP Mikasa Series Bedienungsanleitung

Masalta

Masalta MDR65 Series Bedienungsanleitung

Weber mt

Weber mt SRV 300-II Betriebsanleitung

SPERO

SPERO SP1400 Bedienungsanleitung

Weber mt

Weber mt CR 2 Betriebsanleitung