Wenger Attic Storage System Bedienungsanleitung

©Wenger Corporation 2008 Printed in USA 04/08 Part #259A098-01

Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448

Questions? Call.....USA: (800) 733-0393 • International (call collect): (507) 455-4100 • www.wengercorp.com

CONTENTS

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important User Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Parts and Fastener List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Please read and understand these Assembly Instructions before working with or using the Attic.

If you need additional information about the Attic, contact Wenger Corporation using the information

below.

Your Performance Partner

Assembly Instructions

Attic Storage System

SAFETY PRECAUTIONS

Make sure that anyone

working on the Attic Storage

System has read and

understands this manual.

!CAUTION

Failure to comply with

Warnings and Cautions in

this document can result in

damage to property or

serious injury.

!CAUTION

Always observe and comply

with the Warnings and

Cautions posted on the

system equipment.

!CAUTION

This manual contains cautions which are defined as follows.

• CAUTION; failure to follow the instruction may result in serious injury or damage to property.

Read all of these safety instructions before assembling the attic.

The Attic Storage System is guaranteed free of defects in materials and workmanship for ten years on

the frame and five years on the cover.

Our guarantee assures you of either a full refund or repair or replacement of the defective materials or

workmanship without charge, at the discretion of our Customer Service Department. Just call a

Customer Service Representative at 1-800-887-7145 and state the reason you are dissatisfied. If a

product return is necessary, your representative will issue a return authorization. This is your sole

remedy for breach of this warranty.

Should you have a question or problem with any Wenger product, don’t hesitate to call, even if the

product is past warranty. It’s important to us that all our customers be satisfied.

This is the sole warranty made by Wenger. Wenger disclaims all other warranties, including the

warranties of merchantability and fitness for a particular purpose, as well as all liability for incidental,

consequential, special, and indirect damage. Wenger liability for direct damages shall be limited to the

amount you paid for the product involved. Wenger reserves the right to make product changes without

obligation to incorporate such changes into products previously sold.

Some states do not allow the exclusion or limitation of damages or warranties, so the above may not

apply to you. This warranty gives you specific legal rights. You may also have other rights which vary

from state to state.

WARRANTY

IMPORTANT USER INFORMATION

GENERAL

any form or by any means including graphic, electronic, or mechanical methods or photocopying,

recording, or information storage and retrieval systems without the written permission of the publisher,

unless it is for the purchaser's personal use.

The information in this manual is subject to change without notice and does not represent a commitment

on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any

errors that may appear in this manual.

In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for

direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this

manual.

The information in this document is not intended to cover all possible conditions and situations that might

occur. The end user must exercise caution and common sense when assembling or installing Wenger

Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-733-0393.

MANUFACTURER

The Attic Storage System is manufactured for:

Wenger Corporation

555 Park Drive

Owatonna, MN 55060

1-507-455-4100 • 1-800-733-0393

www.wengercorp.com

INTENDED USE

•This product is intended for indoor use in normal ambient temperature and humidity conditions - it

must not be exposed to prolonged outside weather conditions.

•This product is intended to be assembled only as described in these instructions.

•Remove components from packaging carefully.

•Use corrugation as a cushion on which to assemble.

•Keep hardware together until needed for assembly.

•It is recommended that two people are used in the assembly process to ensure easy installation

without damage to cover.

BEFORE ASSEMBLY

Item Qty Description Item Qty Description

1 1 Attic Storage System Cover 6 8 Flange Lock Nut

2 2 Front Frame 7 8 Machine Screw, #10-24 x 2"

3 2 Side Frame 8 4 Wood Screw #8 x 2 1/2"

4 1 Bottom 9 2 Wood Screw #8 x 1 1/4"

5 4 Plastic Square Plug

The following tools are required to assemble the Attic.

•Phillips #2

•7/16" Open and Box Wrench

•Rubber Hammer

REQUIRED TOOLS

1. Remove the Assembly and Owners manual.

2. Remove the two 1 x 4” boards and protective cardboard from each side of the crate assembly.

3. Cut and remove the plastic wrap that encloses the Attic Storage System Assembly.

PARTS AND FASTENER LIST

YourPerformance Partner

To begin the assembly of the Attic:

1. Hold a front frame (item 2) weldment with

the 3/4" x 1 1/2" tubing horizontal. Some

assistance may be required.

2. Position a side frame (item 3) behind the

front frame (item 2). (figure A)

Note: The offset holes allow the side frame to

be flush with the bottom of the front

frame and allow a height difference

between the tops of the two frames.

This gap is where the floor fits when

the unit is turned over.

3. Insert the 2" long machine screw (item 7)

through the front frame and then through

the side frame. Screw heads on the

outside of the front frame. Assemble the

nuts (item 6) snugly with the knurl locking

feature toward the tube. (figure A)

4. Position the other front frame (item 2) to

the back of the side frame and repeat step

3. (figure B)

5 Position the other side frame (item 3)

between the two front frames. Install the

hardware as described in step 3. (figure C)

6. Once the front and back frames are

uniform with the side frames flush with the

ends of the front frames and all frames

resting on the corrugation or floor, hold the

corners square and tighten all fasteners.

ASSEMBLY

figure A

figure B

figure C

7. Turn the frame assembly over, there should be a 3/4" gap under the side frames for clearance for

the floor material.

8. Install the four plastic square plugs (item 5) into the outermost top corners of the front frame tubing

weldment. The plugs will protect the Attic Storage System cover when it is being installed. Inspect

for burrs or other sharp edges that may damage the cover and remove them with a file if necessary.

(figure D)

9. With two people, carefully slide the cover, with the zippers closed, over the frame so that the logo is

toward the front and the seams are evenly and neatly arranged along the edges of the interior

frame. Avoid cutting or tearing the fabric by pulling the cover down evenly and slowly along all four

corners at the same time. Stop if there is a snag or excessive tightness until the material can be

moved freely into position. Two people are needed to install for optimal fit and appearance. (figure E)

Note: During cold weather, allow cover to reach room temperature prior to placing over the frame assembly.

figure D

3/4"

gap

3/4"

gap

ASSEMBLY (CONTINUED)

Your Performance PartnerYour Performance Partner

figure E

INSTALLATION

10. Two people and step ladders are required to lift the floor (item 4) into position on top of the

cabinet(s). Measure first to be certain that the width and depth are correct and that the height (30")

of the Attic Storage System Storage System will not be obstructed.

11. Position the floor (item 4) 3/4" back from the front edge of the base cabinet. The holes on each

end of the floor should be aligned with the center of the cabinet(s) end panels.

12. Once the floor is aligned into position insert a 1 1/4" wood screw (item 9) into the center counter-

bored hole on each side of the floor. Drive the screw into the end panel of the cabinet to secure the

floor into position. (figure F)

13. Two or more people and step ladders are required to lift the frame and cover assembly up over the

floor and to set it down securely on top of the cabinet(s). This will be easier with the zippers all the

way open. Grasp the frame assembly securely and avoid getting fingers pinched between the frame

assembly and the sharp edges of the floor.

14. Be certain that the frame assembly is centered on the floor. With assistance, lift the back frame up

enough to bring the back material flap underneath the frame and up between the frame and the

floor. (figure G)

15. Repeat for the front flap.

Check all fasteners before

moving or raising the unit.

!CAUTION

Keep hands and fingers free

of being pinched.

!CAUTION

Cover

Rear Frame

Floor

Pull Flap

figure G

YourPerformance Partner

Attic Floor

Base Cabinet

Material Flap

figure F

3/4"

16. Once the front and rear flaps are pulled in place, insert wood screws through the clearance holes in

the side frames and the floor and then into the center of the cabinet(s) side panels. Do not let the

screw wander to the side or at an angle as damage to the cabinet(s) may result. Do not fully tighten

the screws against the frame at this time, keeping about 1/8” clearance between the screw head

and the tubing.

17. Pull the cover down to best fit position, pull the rear flap up to tighten the rear fabric panel. Pull the

front flap up to approximately the same position as the rear flap and carefully close the zippers to

check that the front flap is lightly tensioning the front cover to keep it straight. Repeat as necessary.

18. Open the zippers and tighten the side screws to hold the Attic Storage System assembly in position

on top of the cabinet.

19. Note the information on the white tag on the inside, upper rear seam of the cover and be certain that

it is legible and not obstructed by items stored in the Attic Storage System during use.

20. The zippers may be locked by passing a small padlock through the holes in the zipper pulls.

21. Do not place any items on top of the Attic Storage System cover or frame.

22. Do not allow items stored inside the Attic Storage System to rest against the fabric cover.

23. The fabric cover is not fire rated.

24 Do not exceed a load of 40 lbs per foot of width, evenly distributed, on the floor of the attic.

25. Unstable or heavy items should be placed in the rear corners to allow more stability and lighter

items to be near the front of the Attic Storage System when the zippers are opened and closed.

INSTALLATION (CONTINUED)

Attic Width Max. Weight Capacity

27" (69 cm) 90 lbs (41 kg)

42 1/2" (108 cm) 142 lbs (64 kg)

48" (122 cm) 160 lbs (73 kg)

54 1/2" (139 cm) 182 lbs (82 kg)

60" (152 cm) 200 lbs (91 kg)

Inhaltsverzeichnis

Andere Wenger Lagerung Handbücher

Wenger

Wenger 1-Column Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung