West Penn Wire AV-IP-NC811 Bedienungsanleitung

AV-IP-NC811

Operation Manual

AV-IP-NC811 IP Device Controller Operation Manual

SAFETY PRECAUTIONS

To insure the best from the product, please read all instructions carefully before using

the device. Save this manual for further reference.

Follow basic safety precautions to reduce the risk of fire, electrical shock and injury

to persons.

Do not dismantle the housing or modify the module. It may result in electrical shock

or burn.

To prevent fire or shock hazard, do not expose the unit to rain, moisture or install

this product near water. Keep the product away from liquids.

Spillage into the housing may result in fire, electrical shock, or equipment damage.

If an object or liquid falls or spills on to the housing, unplug the module immediately.

Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to

the device before cleaning.

Using supplies or parts not meeting the product’s specifications may cause damage,

deterioration or malfunction.

Refer all servicing to qualified service personnel.

Install the device in a place with good ventilation to avoid damage due to

overheating.

Unplug the power cord when left unused for a long period of time.

Do not put any heavy items on the unit or on extension cable.

Do not remove the housing of the device as you may be exposed to dangerous

voltage or other hazards.

Information on disposal of devices: do not burn or mix with general household

waste, please treat them as normal electrical wastes.

Unpack the equipment carefully and save the original box and packing material for

possible future shipment.

Please read this user manual carefully before using this product.

AV-IP-NC811 IP Device Controller Operation Manual

Contents1.

Contents....................................................................................................................31.

Introduction ...............................................................................................................42.

2.1. Introduction to the AV-IP-NC811 ....................................................................4

2.2. Features.........................................................................................................4

Package Contents.....................................................................................................43.

Specification..............................................................................................................54.

4.1. Product overview ...........................................................................................5

4.2. Installation Procedure....................................................................................6

4.3. Ethernet Web Interface –Device Management ...........................................17

AV-IP Transmitter AV-IP-WP772..............................................................................195.

AV-IP Receiver AV-IP-RX776 ..................................................................................346.

7. Audio AMP IP TX and RX........................................................................................49

8AV-IP-C8-WH..........................................................................................................66

9Troubleshooting.......................................................................................................73

AV-IP-NC811 IP Device Controller Operation Manual

Introduction2.

2.1. Introduction to the AV-IP-NC811

The AV-IP-NC811 IP Device Controller is a Linux-based PC that allows users to control

hub-installed West Penn Wire products via Web interface.

When installed on a local area network (LAN), the IP Device Controller can scan the

LAN for connected West Penn products and allows the user to auto-discover, configure

and control these products through an Ethernet Web interface. The Controller may also

be used to manage firmware upgrades of connected West Penn Wire devices. An

Application Program Interface (API) is available to allow the West Penn Wire 8-Button IP

Controller (AV-IP-C8-WH) to send commands to the IP Device Controller.

Applications include but are not limited to commercial and residential AV systems,

classroom projector systems, digital signage, video wall systems, boardroom systems,

multi-room systems, classroom training, retail systems, collaborative PC systems, and

medical information systems.

2.2. Features

Centralizes control of West Penn Wire products within a system

Provides a web interface to manage & control West Penn Wire products

Provides a control API for the 8-Button IP Controller (AV-IP-NC811)

Supports I/O presets to be configured

Serves as a base platform to develop automation control applications

Supports software upgrades

Package Contents3.

One (1) AV-IP-NC811 IP Device Controller

One (1) External Power Adapter

AV-IP-NC811 IP Device Controller Operation Manual

Specification4.

AV-IP-NC811 IP Device Controller

CPU

Intel Z3735F

Memory

2GB DDR3

BIOS

AMI BIOS

VGA

Resolution up to 1920 x 1200

Keyboard and

Mouse

USB keyboard and mouse (sold separately)

Peripherals

• USB 2.0 ports (3x)

• micro SD slot (1x)

• Network interface (1x)

• VGA Video out port (1x)

• HDMI Video out port (1x)

• Audio in via 3.5mm port (1x)

• Audio out via 3.5mm port (1x)

Operating System

Ubuntu 14.04 LTS

Operating

Temperature

5 ºC to 50 ºC

Dimensions

4.52 x 4.52 x 1.4 inch (115 x 115 x 35 mm)

Weight

1.1lbs (0.5kg)

Accessories

Included

External Power Adaptor

Regulatory

FCC, CE, RoHS, WEEE

Order Information

AV-IP-NC811 IP Device Controller

4.1. Product overview

The external connections and connection indicators of the AV-IP-NC811 Network

Controller are detailed in Figure 4 and Figure 5. Please familiarize yourself with them

before installing the unit.

AV-IP-NC811 IP Device Controller Operation Manual

A1 = DC Power

A2 = VGA video out

A3 = HDMI video out

A4 = RJ45 Ethernet

A5 = Audio in (not supported in current software release)

A6 = Audio out (not supported in current software release)

A7 = Micro SD Memory Slot (not supported in current software release)

A8 = K Lock

A9 = WiFi antenna (not supported in current software release)

B1 = USB 2.0 #1

B2 = USB 2.0 #2

B3 = USB 2.0 #3

4.2. Installation Procedure

Note that the WiFi antenna on the West Penn Wire Controller is not supported in the

current software release.

Figure 1: Rear Panel

Figure 2: Side Panel

AV-IP-NC811 IP Device Controller Operation Manual

Setting the Ethernet Switch & Router to the same Subnet as West Penn Wire

Devices:

The AV-IP-NC811 comes with a default static IP address of 192.168.168.50 (with

DHCP disabled). All the West Penn Wire AV-IP Systems are set to support DHCP by

default. When no DHCP server is available both, transmitters and receivers fallback

to a static IP address of:

•AV-IP-C8-WH: 192.168.168.54

•AV-IP-AMPTX: 192.168.168.55

•AV-IP-AMPRX: 192.168.168.56

•AV-IP-WP772: 192.168.168.58

•AV-IP-RX776: 192.168.168.59

These products work in conjunction with a PoE (PSE) Ethernet Switch. The

WPTL-SG1005P is recommended for point to point applications while managed

ones are suggested for room collaboration.

In order for the DHCP server within the Ethernet Switch to support the West Penn

Wire device subnet, set the static IP of the Ethernet Switch to 192.168.168.1

(recommended setting). Refer to the Ethernet Switch manual for instructions on how

to accomplish this.

Setting West Penn Wire Devices and Ethernet Switch to an Existing Subnet:

If the AV-IP devices are being installed in an existing environment that has a working

subnet already configured that cannot be easily changed, then the subnet of the

West Penn Wire devices and the Ethernet Switch (if a new Ethernet Switch is

required) must be changed in order to match the existing subnet. For this case we

will use 192.168.2.x as an example subnet already in place and which must be

supported. Note that this is only an example and may not necessarily reflect your

actual subnet address.

If the Ethernet Switch does not already reside in the example subnet of 192.168.2.x,

then set the static IP of the Ethernet Switch to a free static IP address (for the sake of

this example we will use an IP address of 192.168.2.1). Refer to the Ethernet Switch

manual for instructions on how to accomplish this.

The West Penn Wire AV-IP devices are set by default to support DHCP, and will

automatically be set to the subnet specified by the DHCP Server. These units need

only be physically connected into the network as described in their respective

Installation Guides and by using the AV-IP-NC811 to discover them. But before the

MNC can be used, the new MNC subnet must also be set.

AV-IP-NC811 IP Device Controller Operation Manual

To change the subnet of the MNC requires a two-step process:

Process 1: Configuring the IP address of the MNC

Process 2: Physically installing the MNC in the network

Note:

• An example subnet address of 192.168.2.x of the existing network on which

the MNC will be installed is assumed for this example process.

• The MNC comes with a static IP address of 192.168.168.50 and with DHCP

disabled. This process explains how to change it to the example subnet of

192.168.2.x.

Process 1: Configuring the IP address of the MNC

Refer to Figure 1 and Figure 2.

1. On the back panel of the MNC:

A. Plug the supplied power adaptor into the DC power jack. Ensure that the

other end of the power adaptor is plugged into a power socket.

B. Ensure that the power switch on the front of the unit is in the ON position

(front button • pressed in).

C. Connect one end of an Ethernet cable to the Ethernet port. Ensure that

the other end of the Ethernet cable is connected to a computer.

Refer to Figure 3.

2. On the computer to which the MNC is connected, open up an Internet

browser (Explorer, Chrome, Firefox, etc.) and type the following address in

the address bar near the top of the screen:

http://192.168.168.50/mnc/

NOTE: mnc must be written in lower case

Figure 3: Internet Browser Entry

AV-IP-NC811 IP Device Controller Operation Manual

3. Press Enter on the keyboard. If the browser connects to the MNC, go to

Step 7

4. If the browser fails to connect to the MNC, a failure message will appear.

Perform the following steps (Steps 4 through 6) in order to set the computer

to the same subnet as the MNC, to be able to then change the MNC subnet

(from Step 7 onward) to match the subnet of the existing installation (refer

to Figure 5)

A. Move the mouse to the bottom of the screen and click on the Start

button at the lower left.

B. Click into the Search programs and files field just above the Start

button and type cmd. Press Enter on the keyboard.

C. A DOS window will appear. Type ipconfig and press Enter on the

keyboard.

Figure 4: Determining Computer IP Address

AV-IP-NC811 IP Device Controller Operation Manual

The following screen will appear (Figure 5)

5. If the IPv4 Address (shown in the red box of Figure 8) does NOT begin with

the numbers 192.168.168.x, then perform the following steps (refer to

Figure 6 through Figure 9):

A. Type exit and press Enter on the keyboard

B. Move the mouse to the bottom of the screen and click on the Start

button at the lower left.

C. Click on Control Panel

D. Click on Network and Internet

E. Click on Network and Sharing Center

F. Click on Local Area Connection

G. Click on Properties

H. Click on Internet Protocol Version 4 (TCP/IPv4). It will turn blue.

I. Click on Properties

J. Click on the Use the following IP address radio button

K. In the IP address field, type the following: 192.168.168.x

Where x can be any number from 2 to 254 except for 50 (since 50 is the MNC

address). The example in Figure 9 has the PC set to a Static IP address of

192.168.168.12

Figure 5: Computer IP Address

Andere Handbücher für AV-IP-NC811

Inhaltsverzeichnis

Andere West Penn Wire Controller Handbücher

West Penn Wire

West Penn Wire AV-IP-NC811 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung