Westermo GDW-11 Montage- und Bedienungsanleitung

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

Moeller Easy Relay & GDW-11

Remote Access Over GSM

AN-0133-ENG rev1.1 Page 1

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

Contents

1. ntroduction…………………………………………………………..

2. Configuring the GDW-11…………………………………………...

3. Configuring EASY-SOFT Pro……………………………………...

4. nterface connection details………………………………………..

5. Configuring Hyperterminal………………………………………….

6. Using EASY-SOFT Pro to communicate remotely……...……….

7. Closing down the modem connection…………………………….

Page 3

Page 4

Page 6

Page 7

Page 8

Page 10

Page 11

AN-0133-ENG rev1.1 Page 2

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

1. Introduction

n the above application, the PC will be able to connect to the Easy Relay device using a

GDW-11 modem connected to the GSM network. The PC will need to have an external

modem connected to establish a call to the remote location. t is not possible to use an internal

modem, as EASY-SOFT Pro only allows communication via COM ports.

This application note will explain what is required to setup a GDW-11 modem and the Easy-

Soft Pro software to enable programs to be downloaded and uploaded to the Easy Relay unit.

n order to complete these instructions you will need the following items as a pre-requisite:

CSD Enabled S M Card with a separate data number assigned

EASY-SOFT Pro V6.20

Moeller PC-CAB Serial nterface lead

GD-Tool configuration software

Straight through, male to female, 9 way serial cable (for programming GDW-11)

A suitable S M card can be bought through Westermo. We will arrange for the data number to

be assigned at the time of purchase.

f you only have EASY-SOFT Pro V6.10, update to V6.20 by using the update link within the

menu of the program.

The GD-Tool configuration software is supplied on a CD-ROM with the GDW-11, or it can be

downloaded from the Westermo website: www.westermo.co.uk

The serial cable will need to be fully terminated, GD-Tool will not work with just pins 2,3 & 5

connected!

GSM

Network

AN-0133-ENG rev1.1 Page 3

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

2. Configuring t e GDW-11

Start the GD-Tool program and connect the PC to the GDW-11 with the serial cable. Power

up the modem, then click on the Autoconnect button to establish comm’s.

Once GD-Tool has read all of the settings in the modem, there will be several tabs available

to click on. For this application, we are only interested in the Basic and Serial tabs.

Configure the serial port for a

bit rate of 9600 and ensure that

flow control is enabled, as

shown on the left.

At the bottom of the screen

click on the “Write” button to

store these settings in the

modem

Click here to

commence comm’s

AN-0133-ENG rev1.1 Page 4

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

Now click on the Basic tab to configure the connection details. Set the boxes as shown

below and then click on the “Write button” to store these settings.

That completes the setup of the GDW-11 modem. Close GD-Tool and disconnect the

serial cable to the modem.

AN-0133-ENG rev1.1 Page 5

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

Run the Easy-Soft configuration software and navigate to the communication option on the

menu bar. Click on the nterface option and select the desired COM port to be used. Then set

the nterface baud rate to 9600, as shown below.

3. Configuring EASY-SOFT Pro

Navigate back to the communication menu and

select nterface, followed by the timeout option.

The box shown on the left will appear, Change

the “PC => Local Device” value to 10000 ms.

gnore the “PC => Net Station” setting and click

on the “OK” button.

Set baud

rate to 9600

Select COM

port for t e

connection

AN-0133-ENG rev1.1 Page 6

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

To enable communication between the modem and the Easy relay, it is necessary to make

up an interface cable. The drawing below shows the required connections.

Connect the cable between the two devices, ensuring that the correct end is fitted to the

relevant port.

4. Cable connection between GDW-11 & Easy Control Relay

Connect this

end to the

GDW-11

serial port

Connect this

end to the

Easy PC-CAB

lead

Now power up the GDW-11 and Easy Relay units. After a few seconds check that the

GDW-11 NET LED is flashing to indicate network availability.

9 Pin D Sub

(Male)

9 Pin D Sub

(Male)

nterface cable

AN-0133-ENG rev1.1 Page 7

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

5. Configuring Hyperterminal to make a connection

Attach the serial cable to the external modem and make sure that the modem is powered up.

Click on the Windows start button, go to Programs, Accessories, Communications and select

Hyperterminal. When the program starts choose a name for your connection and select “OK”.

Set-up the COM port for the settings

shown on the left and click on the OK

button.

When this dialogue box appears set the

“Connect using” box to the COM port

connected to the external modem.

Then click on the OK button

AN-0133-ENG rev1.1 Page 8

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

The main terminal window will

now be displayed. To test the

modem is responding type the

command:

AT <CR>

The modem should respond with

“OK”.

f you don’t see any characters when you type the commands, it is likely that the echo is

switched off. This will not affect the operation of the modem, but if you wish to see what

you’re typing, use the command:

ATE1<CR> (switches the echo on)

Now type the following commands in turn:

AT&D0<CR> (this will tell the modem to ignore the DTR line status)

AT&W<CR> (this will store the above setting into memory)

To dial out to the GDW-11:

ATDxxxxxxxxxxx<CR> (where xxxxxxxxxxx is the data number of the GDW-11)

Note: Remember to precede your data number with a 9, if you are calling from an internal

exchange.

Once the modem has connected, a status message will appear on the screen to indicate a

successful connection. The screen shot shown above details the sequence more obviously.

Now that the modem connection is established, it is necessary to disconnect the

Hyperterminal session to allow the EASY-SOFT Pro program to use the same COM port

connection.

t is not necessary to close Hyperterminal to

disconnect the session. Just click on the button on

the tool bar shown on the left.

T h e b o t t o m l e f t c o r n e r s h o u l d i n d i c a t e

“D isconn ecte d” to s how the st atus o f t he

connection.

Click t is button to

disconnect t e

session

AN-0133-ENG rev1.1 Page 9

www.westermo.com

Moeller Easy Relay & GDW-11 www.westermo.com

Application Note

With the modem connection established and Hyperterminal session disconnected, bring

up the EASY-SOFT Pro program.

6. Using EASY-SOFT Pro to communicate remotely

Click on the “Online” button and wait. There

will be a delay while the software attempts

t o c o m m u n i c a t e o v e r t h e m o d e m

connection. Once it has established a link

with the Easy Relay, the “Online” button

becomes greyed out and the “Offline” button

becomes available.

Greyed out

once link is

establis ed To download the program from the remote

unit, click on the “Device=>PC” button. .

Once the download starts, a progress bar

will appear.

To upload a program, open the required file

and click on the “PC=>Device” button. f the

remote unit is running, you will be prompted

to confirm that the unit can be stopped to

perform this function

Once you have completed the file transfer,

click on the “Offline” button to close the

connection to the remote unit.

Now close the EASY-SOFT program

before re-connecting the Hyperterminal

session.

Now click on the “Connection” box at the

to p l e f t of t he sc ree n t o r ev e al th e

connection panel.

n t h e l e f t han d c or n e r cli c k on th e

“Communication button” When prompted,

select the type of Easy Relay device you will

be connecting to.

AN-0133-ENG rev1.1 Page 10

Andere Handbücher für GDW-11

Inhaltsverzeichnis

Andere Westermo Modem Handbücher

Westermo

Westermo MD-12 AC Bedienungsanleitung

Westermo

Westermo Pilot Wire RPW600M Bedienungsanleitung

Westermo

Westermo ODW-631 Bedienungsanleitung

Westermo

Westermo MA-14 Bedienungsanleitung

Westermo

Westermo TD-36 Bedienungsanleitung

Westermo

Westermo ODW-630-F1 Bedienungsanleitung

Westermo

Westermo TD-22 AC Bedienungsanleitung

Westermo

Westermo TD-32B DC EU Bedienungsanleitung

Westermo

Westermo ODW-700 Series Bedienungsanleitung

Westermo

Westermo TDW-33 Bedienungsanleitung

Westermo

Westermo ODW-610-F2 Bedienungsanleitung

Westermo

Westermo GS-01 Bedienungsanleitung

Westermo

Westermo TR-36B Bedienungsanleitung

Westermo

Westermo TR-36 Bedienungsanleitung

Westermo

Westermo TD-23 Bedienungsanleitung

Westermo

Westermo 6196-2230 Bedienungsanleitung

Westermo

Westermo ODW-620-F2 Bedienungsanleitung

Westermo

Westermo ODW-720-F1 Bedienungsanleitung

Westermo

Westermo TD-32 B Bedienungsanleitung

Westermo

Westermo ODW-710-F1 Bedienungsanleitung

Westermo

Westermo GDW-11 Bedienungsanleitung

Westermo

Westermo ODW-710-F1 Bedienungsanleitung

Westermo

Westermo MA-43 Bedienungsanleitung

Westermo

Westermo MA-12 AC Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung