Western Co WRD Bedienungsanleitung

WRD

Remote display for WESTERN WRD SYSTEM

Manuale utente

User manual



Manual del usuario

Benutzerhandbuch

WRD

User manual

REV 2.1 FW 2.4 25-09-2020

REMOTE DISPLAY FOR WESTERN WRD SYSTEM

IoT Remote Display and Datalogger 12/24/48V

WRD is a display and controller device that together with the proprietary

bus WBUS is part of the WESTERN WRD SYSTEM, a complete and

intelligent system for the production and storage of photovoltaic energy in

stand-alone systems.

The WESTERN WRD SYSTEM is a flexible and advanced stand-alone system

with intelligent functions, recording of historical functioning data with

remote control from the Internet (cloud). Up to 8 MPPT controllers WRMxx

can be parallelized with adjustable charging power up to 14kW and monitor

the battery bank energy through the battery monitor WBM. WRD is suitable

for 12/24/48V systems with lead or lithium batteries. The system is modular

as WRMxx controllers can be paralleled to increase the photovoltaic power.

WRD has a proprietary control bus named WBUS to communicate with the

various compatible devices, able to access all the parameters both for the

display and for the management of the control functions. The simple user

interface, with 128x64 display and 4 buttons, allows an immediate

visualization of all the parameters: powers, voltages, charge and PV string

currents, energy meters, data logger and events. From WRD all Setup

settings can be made for each single WRMxx controller connected and/or

WBM battery monitor. Through WBM is possible to manage contacts

related to the charge state of the battery for the intelligent activation of the

            

Through the Ethernet connection it is possible to connect to the Internet

cloud so that both the data of the logger and all the other functions

become remotely and accessible with the portal WRD SERVER.

Power supply 12V, 24V and

48V

Backlighted LCD 128x64

Internal clock

Data logger on extractable



Master for WESTERN WRD

SYSTEM

WBUS Interface

Internet connection (cloud)

Cloud monitoring platform

RJ45 Ethernet

Installation from panel or with

frame

IP20 Metallic box

Anti-reverse protection

WRD

Manuale utente

Contents

1. GENERAL DESCRIPTION ...................................................................................................................................... 3

1.1. Viewer .......................................................................................................................................................... 3

1.2. Controller ..................................................................................................................................................... 3

2. CONNECTIONS AND INSTALLATION ................................................................................................................... 3

2.1. Installation procedure ................................................................................................................................. 3

2.2. Possible Configuration ................................................................................................................................. 4

2.3. System Setup ............................................................................................................................................... 4

2.4. Date Time Setup .......................................................................................................................................... 4

2.5. Data Logger Setup ........................................................................................................................................ 4

2.6. Network Setup ............................................................................................................................................. 4

3. MENU NAVIGATION............................................................................................................................................ 5

4. ELECTRICAL FEATURES ........................................................................................................................................ 6

5. MECHANICAL DIMENSIONS ................................................................................................................................ 6

6. FIXING OPTIONS: ................................................................................................................................................ 7

7. IOT PLATFORM FOR MONITORING AND REMOTE CONTROL............................................................................. 8

8. CONFIGURATIONS .............................................................................................................................................. 9

8.1. Configuration: WRD + WBM ........................................................................................................................ 9

8.1.1. Description ............................................................................................................................................ 9

8.1.2. Main screens ......................................................................................................................................... 9

8.2. Configuration: WRD + WRMxx (1 ..8) .............................................................................................................. 9

8.2.1. Description ............................................................................................................................................ 9

8.2.2. Main screens ......................................................................................................................................... 9

8.3. Configuration: WRD + WBM + WRMxx(1 ..8) ............................................................................................... 10

8.3.1. Description .......................................................................................................................................... 10

8.4. Configuration: WRD + Leonardo System ................................................................................................... 10

8.4.1. Main screens ....................................................................................................................................... 10

9. MAIN SCREENS ................................................................................................................................................. 11

10. SETUP MENU: ................................................................................................................................................. 13

11. WARRANTY ..................................................................................................................................................... 22

12. WASTE DISPOSAL ............................................................................................................................................ 22

APPENDIX at the end of the manual

WRD

Manuale utente

1. GENERAL DESCRIPTION

Pic.1 WESTERN WRD SYSTEM with WRM30 +

In WESTERN WRD SYSTEM, WRD is the coordinator and can work in two modes: Viewer or Controller.

1.1. Viewer

By setting in the setup menu 8.4 WRD -> Oper.Mode: 'MONITOR': you get the View mode.

In this mode, the WRD does not control the charging and discharging of the system, but takes care only of displaying the

parameters of the connected devices, can change the setup settings of the slaves, collects data and remotely displays

them in the cloud. The various devices autonomously perform their main functions independently from the WRD.

1.2. Controller

By setting in the setup menu 8.4 WRD -> Oper.Mode: 'CONTROLLER': you get the Controller mode1.

In this mode, the WRD adds a control over the devices, dynamically modifying some parameters in order to optimize the

energy management of the entire system and ensure compliance with the battery parameters.

The operating mode of the WRD in menu 2.0 can be recognized from the indication in the battery graphics (§ Main

screens).

2. CONNECTIONS AND INSTALLATION

In the appendix (Pic. A1, An) the system connections are shown for the various possible configurations.

For its functioning the WRD uses the 12/24 / 48V system power supply and the connection WBUS which is physically an

RS485 bus, while the RJ45 Ethernet connection to the Internet cloud is optional.

The WESTERN WRD SYSTEM must be configured by setting to each WRMxx controller a unique address: from 1 to 32,

while the WBM already has a fixed address (33) as in the case of connection with a Leonardo (34).

2.1. Installation procedure

1) To install the WRD in a dry place, there are two fixing options: from the panel and with frame (Pic.4)

2) At the back you can access the electrical connections (Pic.4). Both the power connection and that of the WBUS are2

of a removable clamp type, easy to wire. Connect the cables correctly, if the power supply comes from the battery, it

is recommended that it is under the use of a fuse (0.5A) for cable protection. Finally, if it is used, also connect the

Ethernet cable.

3) Once all the connections have been made, power up the system. The WRD turns on and starts to function.

4) Now run the system configuration settings that will be required.

At the menu: 8.0 WBUS CONFIG. you can use the 'AutoConf.' command for simplicity, or you can make address

settings manually.

At the menu: 7.1 DATE / TIME you set the clock and time zone (Timezone).

At the menu: 7.0 SYSTEM you make system settings. The correct profile must be selected, corresponding to the

battery features (an incorrect choice could lead over time to damage the battery itself).

1 It is recognizable if a WRM30+ is remotely controlled (by WRD) if, on the WRM30+ display, the battery contour flashes every ~3sec.

2 The WBUS has the RS485 as its physical bus, so the two poles A and B must be connected correctly, while the GND pole should be left disconnected.

WRD

Manuale utente

5) Check the entire functioning by scrolling the screens.

2.2. Possible Configuration

The WESTERN WRD SYSTEM can work with different combinations of devices.

Configurations

Monitoring

Diagrams in Appendix

WRD + WBM

battery

WRD + WRMxx(1..8)

PV production

A2, A3

WRD + WBM + WRMxx(1..8)

battery, PV production, consumption

A4, A5

WRD + Leonardo Off-Grid

A6, A7

Depending on the current hardware, the configuration must be set on the WRD. This operation is performed on the

menu: 8.0 WBUS CONFIG. where the addresses of the devices connected to the device must be specified WBUS to

facilitate the operation an auto configuration command is available that detects the connected hardware.

Depending on the configuration set, the WRD displays the information and can execute its algorithms using the

available resources. The screens for each configuration are described below.

2.3. System Setup

In the menu: 7.0 SYSTEM the system settings are executed, the list of parameters changes according to the current

configuration. Detailed explanations are described in the chapter Configurations.

2.4. Date Time Setup

In the menu: 7.1 DATE / TIME you set the system clock and the time zone (Timezone). It is important to correctly set

this last parameter with the Timezone of the place where the system is located, so that the remote clock can be

updated correctly.

2.5. Data Logger Setup

In the menu: 7.2 DATA LOGGER you can enable the data logger by setting the minutes for the sampling parameters:



2.6. Network Setup

In the menu: 7.3 NETWORK you make the settings of the various network parameters. The DHCP function is set by

default, which automatically retrieves the necessary values. The connection to the remote server can be enabled or

disabled by the user.

WRD

Manuale utente

3. MENU NAVIGATION

Navigating through the various screens is very simple and intuitive. The WRD has two display environments (Pic.2):

-the main environment MAIN, consisting of six screens where the operation of the system is monitored;

-SETUP setting environment, consisting of 6 screens + 5 in ADV. SETUP where the settings for the operation are

set.

In the MAIN environment, the UP and DOWN buttons are used to scroll through the screens from 1.0 to 6.0,

the ENTER button accesses any submenu. Pressing the UP / DOWN buttons simultaneously for 1 sec. you

access the SETUP environment. Here, it is always repeated with the same UP or DOWN buttons, the scrolling of

the screens from 7.0 to 7.5. To return to the MAIN environment use the ESC button pressed for 1 sec.

To enter ADV. SETUP select the "Advanced Setup" item on the 7.5 OTHERS screen, press the UP botton so that "-->"

appears and then press the OK button for 1 sec.

It is possible to enter the EDIT mode (Pic.3), where it is

allowed, to modify the parameters by keeping pressed the

EDIT button for 1 sec. Entry into the EDIT mode is

visible on the display by the presence of the cursors on the

modifiable parameter. For editing are used the /

INC/DEC buttons, press the SELECT button to change

the value. For save the changes the button SAVE must

be kept pressed for 1 sec.

To exit the EDIT mode, without saving the changes, use the

ESC button. To confirm the items that require an

action, press the OK button for 1 sec.

SETUP

MAIN

3.0

VARIABLES

2.0

MAIN B

1.0

MAIN A

4.0

PV STRINGS

5.0

ENERGIES

6.0

LOG.EVENTS

7.1

DATA/TIME

7.0

SYSTEM

7.2

DATA LOGGER

7.3

NETWORK

7.4

INFO

7.5

OTHERS

ADV. SETUP

8.1

WBM

8.0

WBUS CONFIG

8.2

WRMxx

8.3

W-INVERTER

Navigation Menu

8.4

WRD

submenu

NAVIGATION MODE

DOWN

EDIT

ESC

> EDIT MODE <

ESC EDIT

DEC

INC

SELECT

SAVE

GO INTO SETUP

---

Keys mode

Pic.2 - Navigation menu

Pic.3 - Edit menu

WRD

Manuale utente

4. ELECTRICAL FEATURES

DESCRIPTION

PAR.

VALUE

U.M.

Nominal battery voltage

12 / 24 / 48 autodetect

(V)

Supply voltage range

Vbatt

10 ÷ 64

(V)

Self consumption

1.0

(W)

Operating temperature

Tamb

-10 ÷ +40

(°C)

Max cable section terminal (Power and RS485)

1.5

(mm2)

Weight

250

(g)

Dimension LWH

160 x 95 x 27

(mm)

Degree of protection

IP20

Tab.1 - Electrical features

5. MECHANICAL DIMENSIONS

Pic.4 - Mechanical dimensions

WRD

Manuale utente

6. FIXING OPTIONS:

Pic.5 - Fixing options

WRD

Manuale utente

7. IOT PLATFORM FOR MONITORING AND REMOTE CONTROL

The WRD, through the Internet connection and IoT technology, communicates with the remote server and transmits

operating data. By registering and logging into the WRM MONITOR client web interface, it is possible to interact with

the system by changing its settings and, at the same time, monitor its own energy system.

In particular, the user has access to the following features:

Monitoring of the data sent by the system in real time: values of power produced, absorbed/taken from the

battery and consumed by the load, the state of charge of the battery and any alarm status.

Visualization of graphs, counters and indicators related to system statistics: trend of all the typical values of the

system, such as voltages, currents and powers. Possibility to select the display time period.

Reports of events related to the system, such as alarms or useful information.

Specific information of the system installed (type, capacity and battery voltage, device firmware versions).

Pic.6 - WEB Client

Access to the portal

The first time you log in to the WRM MONITOR interface, you need to register. Registration is carried out at the

following link (also valid for subsequent accesses).

http://wrdserver.western.it

You need to enter your name and email address, and then you have to choose a password.

At this point, access to your dashboard is done by clicking on HOME WRM MONITOR.

When you first log in, you must enter the "Select your Device Key" box, as shown in Pic.7 (below), the KEY CODE

identifier of your WRM60 / 90 (e.g. 0123456789ABCDEF) which is written on the label on the side of the product or on

the MENU 7.4 of the display (as described at page 15). Once the code is inserted, press ENTER from the keyboard. At

this point, you can monitor your system and navigate through the various features.

Pic.7 - Key Code Insertion

WRD

Manuale utente

8. CONFIGURATIONS

8.1. Configuration: WRD + WBM

8.1.1. Description

This configuration is used in a plant where you want to monitor the energy flow of the battery (Pic. A1). The WBM

battery monitor must be connected to the negative battery terminal and provides for the calculation of the

incoming and outgoing energy. (See dedicated product manual for more details).

WRD allows configuring the WBM in the Setup menu 7.0 or 8.1:

Select the correct profile according to the type of battery.

Select the battery capacity (Ah) correctly, so that the WBM can correctly calculate the State of Charge (%)

of the Battery.

Set the thresholds for the two contacts controlled according to the State of Charge (%) of the Battery.

The 'Discharge' contact can be exploited to control a device capable of disabling the load, thus determining the

maximum discharge depth within which the battery will cycle. This contact also intervenes in case of protections:

overcurrent, over temperature and under voltage.

With the 'Charge' contact, normally, is controlled a device capable of disabling the charge as it intervenes in the

event of protections: overcurrent, over temperature and overvoltage.

Setting the thresholds for the 'Charge' contact it can also be controlled according to the SoC in case some

applications require it.

8.1.2. Main screens

In the following picture are described the graphic used in the various screens of the main menu.

Take into account the notes shown in the pictures.

8.2. Configuration: WRD + WRMxx (1 ..8)

8.2.1. Description

This configuration is used in a stand-alone system where you want to mainly monitor the energy production

(Pic.A2).

The WRMxx controllers, which can be paralleled up to a maximum of 8, are used to charge the battery. (see

dedicated product manual for more details).

The WRD allows to collectively configuring the most common parameters of all the WRMxx in the Setup Menu

7.0, while it performs this individually in the Setup Menu 8.2.:

Select the correct profile according to the type of battery.

Select appropriately the setting of the Load output

Set the Low Battery threshold for the output Load.

- With the WRM30+: Load output can be exploited with setting 'SurPlus' to control or directly feed a load when

the battery is charged and there is still energy from the PV modules so we have an excess of energy that in this

way can be re-used.

8.2.2. Main screens

In the following picture are described the graphic used in the various screens of the main menu.

Take into account the notes shown in the pictures.

Inhaltsverzeichnis

Andere Western Co Monitor Handbücher

Western Co

Western Co WBM Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung