Wet Sounds ICON8 Leitfaden

wet

sounds

ICON8

Owner's Manual & "Limited" Warranty

Technology Specifications:

Thank You for purchasing this Wet Sounds product. Wet Sounds marine audio products

represent the ultimate in high performance standards. The Icon series is specifically

engineered to withstand the rigorous marine environment. Utilizing state

the art acoustic

engineering and three dimensional computer aided design, the ICON series represents the

most advanced technologies available for wakeboard tower speaker systems. The Icon series

also provides multiple fitment options from direct cast mount to fixed clamp mount to our

revolutionary (Patent Pending) stainless steel TC3 Quick Disconnect Swivel clamp.

Please take a moment to read the instruction manual before starting your installation. This

manual will explain the benefits

the technologies developed by Wet Sounds and will help

you understand the correct installation methods and use

this product.

you have any

questions or concerns please contact a certified Wet Sounds dealer. You may also contact

Wet Sounds technical support by dialing 1-877-WET-SPKR (1-877-938-7757)

SPEAKER SPECIFICATIONS ICON 8

RMS: 150 watts

Peak: 300 watts

Mid Bass: 8 inch composite cone with polyurethane surround

High Frequency: 1 inch HLT Titanium Tweeter

Impedance: 4 ohm

Frequency Response: 20Hz to 20 kHz

Sensitivity: 92DB at 1W/

The ICON series represents the highest level

performance in tower speaker technology for

today's extreme audiophile customers. The ICON series is a high output true sound quality

tower speaker able to provide maximum output while still providing world class sound

quality without the listener fatigue usually associated with high volumes. The unique

qualities

the ICON series components provide remarkable volume and mid bass and

dynamic full range sound quality. A full passive crossover network delivers tuned

frequencies to the driver resulting in rich smooth sound. The driver compliment in each

ICON 8 combines one sealed 8 inch midbass woofer made from composite cone materials

and a grille mounted Wet Sounds

"HLT

" 1 inch titanium tweeter. Utilizing the Wet Sounds

"HL

Tweeter design every type

riding sport from wakesurfer to wakeboarder can enjoy

true quality sound.

***Caution: Do not spray any

the speakers directly with any liquid base substance.

Warranty will be voided

improper care is discovered during extensive examination

ofthe

product.

Installation:

ICON

Fixed

Clamp

TC3-F Fixed

Clamp

Pipe Version Installation (pipe tower)

WireJacket

Allen Bolts(long)

ClampTop

Allen Bolts (short)

SpeakerWire Plug

ClampBase

Male

Connector

Female

Connector

Grommet

Step

Attach Male Connector (7) from clamp base to Female Connector (8)

Step 2: Push connector into center hole

speaker as you place clamp base

onto the speaker housing. Please make sure the grommet (9) is seated properly.

Step 3: Attach two short Allen Bolts (4) through the clamp base and tighten

into the housing. Please make sure these are tight.

is also recommend to use

a Blue Loctite on these bolts.

Step 4: Find the mounting location for the speaker and clamp and then mark the

location

the bottom side

the pipe for the speaker wire. The speaker wire

will

inserted back into the pipe for a clean installation.

Step 5: Drill a small hole in the pipe and de burr the hole so there is no sharp

edges.

is also recommend to install a rubber grommet in this hole to protect

the wire.

Step 6: Slide the wire jacket (1) down the wire and Butt Connect the speaker

wire coming from the tower to the speaker wire plug (5). Red

positive and

black is negative

Step 7: Attach Clamp Top (3) to clamp base (6) using the two long Allen Bolts

(2)

Step 8: Make sure the clamp is tightened all the way so there is no movement

Installation:

ICON 8 SC Swivel Clamp

"Patent Pending" TC3-S Swivel Clamp Version Installation

Allen Bolts (long)

~~I

ClampTop

----

Detachment

Plate

(casttowers)

Clamp

Bottom

Female Speaker Plug

Wire Jacket

Wire Sleeve

Allen Bolts

for

Plate Speaker Plug Screws

Male Speaker Plug Allen Bolts (short)

Bushing

Detachment

Clamp

Base

Bushing

Male Connector

Female

Connector

Allen Loc

king

Bolt

Grommet

Pipe Tower Mount Version using the TC3-S

Step

Attach Male Connector (10) from clamp base to Female Connector (11)

Step

Push connector into center hole

speaker as you place clamp base

onto the speaker housing. Insert 4 bare wires down into this hole as well. These

wires are only used

you are adding the LED speaker rings. (please see LED

speaker install instructions for LED install) Please make sure the grommet (12)

is seated properly.

Step

Attach two short Allen Bolts (16) through the clamp base and tighten

into the housing. Please make sure these are tight.

is also recommend to use

a Blue Loctite on these bolts.

Step 4: Clamp Bottom (3) and Detachment Plate (5) are already connected

together. Insert the detachment plate into the clamp base (9). Please make sure

the male speaker plug (7) and female speaker plug (4) are lined up properly.

The male speaker plug (7) inside the clamp base can rotate. Please rotate this

so that it

facing the proper direction. There is a U shaped groove on the

female that lines up with a boss on the male.

Step

Slide the detachment fork (17) into the grooves on the clamp base.

Attach the allen locking bolt (19) and tighten down.

Step

Find the mounting location for the speaker and clamp and then mark the

location on the bottom side

the pipe for the speaker wire. The speaker wire

will be inserted back into the pipe for a clean installation.

Step

Drill a small hole in the pipe and de burr the hole so there is no sharp

edges.

is also recommend to install a rubber grommet in this hole to protect

the wire.

Step

Slide the wire jacket (13) down the wire and Butt Connect the speaker

wire coming from the tower to the speaker wire plug (4). Red is positive and

black is negative.

you have added the LED accessory, this speaker wire plug

(4) will have 6 conductors. Please refer to the LED install instructions.

Step

Attach Clamp Top (2) to clamp bottom (3) using the two long Allen

Bolts (1)

Step

Make sure the clamp

tightened all the way so there is no movement

Step

The swivel clamp allows you to rotate the speaker any direction you

may want. Loosen the allen locking bolt (19) and rotate the speaker to the

direction you like. Then tighten the bolt to lock it in place.

Step

10:

The swivel clamp also allows you to remove the speaker from the

tower in seconds. Loosen the allen locking bolt (19) and remove the

detachment fork (17). Once removed, the speaker will disconnect from the

clamp. The clamp remains on the tower. To reinstall, line up the male speaker

plug (7) so that it is centered and insert the speaker by plugging the connector

together and reinstalling the detachment fork.

Cast Mount Tower Version using the TC3-S clamp for quick disconnect

and swivel function.

Step

Attach Male Connector (10) from clamp base to Female Connector (11)

Step

Push connector into center hole

speaker as you place clamp base

onto the speaker housing. Insert 4 bare wires down into this hole as well. These

wires are only used

you are adding the LED speaker rings. (please see LED

speaker install instructions for LED install) Please make sure the grommet (12)

is seated properly.

Step

Attach two short Allen Bolts (16) through the clamp base and tighten

into the housing. Please make sure these are tight.

is also recommend to use

a Blue Loctite on these bolts.

Step 4: Clamp Bottom (3) and Detachment Plate (5) are already connected

together. Remove allen bolts (6) that hold the detachment plate (5) to the clamp

bottom (3). Clamp Top (2) and Clamp Bottom (3) will not be used for a cast

tower mount.

Step

The detachment plate (5) will be hard mounted to a cast tower. Butt

connect speaker wires from detachment plate connector (4) to the speaker wires

from the cast tower. Red is positive and Black is negative.

Step

Push wires into center hole back into the tower and attach the

detachment plate to the tower.

Step

Please make sure the male speaker plug (7) and female speaker plug (4)

are lined up properly. The male speaker plug (7) inside the clamp base can

rotate. Please rotate this

that it is facing the proper direction. There is a U

shaped groove on the female that lines up with a boss on the male.

Step

Insert speaker with base onto detachment plate. Slide

detachment

fork (17) and allen bolt (19) and tighten allen bolt

the speaker does not move.

Step

The swivel clamp also allows you to remove the speaker from the tower

in seconds. Loosen the allen locking bolt (19) and remove the detachment fork

(17). Once removed, the speaker will disconnect from the clamp. The

detachment plate remains on the tower. To reinstall, line up the male speaker

plug (7) so that it

centered and insert the speaker by plugging the connector

together and reinstalling the detachment fork.

Male

Connector

-------------

---

male

Connector

Grommet

X Mount Version. Cast tower fixed mount version.

Step

Remove 4 screws holding the grille and driver onto the housing. And

remove the grille and speaker from the housing. Disconnect speaker wires from

mid bass and tweeter. Remove acoustic dampening material.

Step 2: Remove two small Phillips screws from the top

the housing next to

the grommet (2) This will loosen the internal threaded plate.

Step

From inside the housing. Slide out the internal threaded plate and

replace with non threaded plate from X kit. Make sure to install it in the same

direction so the screw holes line up.

Step 4: Remove the center grommet (3) so that the two top plates sit flush on

top

the speaker. Take the two powder coated top plates and attach on top

the speaker. Use two longer Phillips screws provided in the X kit to attach top

plates into internal non threaded plate.

Step

Butt connect Male Connector (1) to the factory wires. Red for positive

and black for negative.

Step

Take housing and hold up to the tower and plug the connectors together

(1) and (2) and push as much back into the tower and feed the remaining and

connectors into the centerhole

the housing.

Step

Take the 2 bolts using the washers and lock washers and bolt the

housing up to the tower. Please make sure that these bolts are tight. Some

towers and adapters will only need a single lock washer and single regular

washer. Other towers and adapters may need extra washers that have been

provided in the kit.

you find that the bolt bottoms out and the housing is not

tight, please add washers to properly seat and tighten the housing to the tower.

(The holes on theplates shouldline up directly with thefactory threadedinsets.

However we have seen some towers that are not threaded in theproper

locations.

this is the case, please contact Wet Sounds

877-938-7757

for

advice)

Step

Insert the acoustic dampening material.

Step 9: Hold the driver up to the housing to connect the speaker wires. Connect

the mid bass speaker wires and tweeter wires. The spade connectors for the mid

bass driver will be a larger size for the (

+) and smaller size for the (-

These

will only install one way on the mid bass driver. The tweeter wire will have a

solid wire and a wire with dash lines. Please make sure to plug the tweeter

wires back together properly matching the non marked with non marked and

dash marked wire with the dash marked wire.

Step 10: Insert the driver into the housing. Insert the grille into the housing

making sure to line up all 4 mounting locations and attach the 4 stainless screws

around to the housing. Please make sure these are tight but DO NOT over

tighten

Dieses Handbuch passt für folgende Modelle

Andere Wet Sounds Sprecher Handbücher

Wet Sounds

Wet Sounds Stealth 6 Ultra Bedienungsanleitung

Wet Sounds

Wet Sounds PRO 60 Bedienungsanleitung

Wet Sounds

Wet Sounds SW·650 Bedienungsanleitung

Wet Sounds

Wet Sounds PRO 80 Bedienungsanleitung

Wet Sounds

Wet Sounds STEALTH Bedienungsanleitung

Wet Sounds

Wet Sounds RECON 6 POD Bedienungsanleitung

Wet Sounds

Wet Sounds REVO V3 Bedienungsanleitung

Wet Sounds

Wet Sounds VENUE Series Bedienungsanleitung

Wet Sounds

Wet Sounds RECON Series Bedienungsanleitung

Wet Sounds

Wet Sounds PRO696RS Bedienungsanleitung

Wet Sounds

Wet Sounds STEALTH 6 CORE Bedienungsanleitung

Wet Sounds

Wet Sounds AR-5 Ranger Crew Bedienungsanleitung

Wet Sounds

Wet Sounds REV 10 HD Bedienungsanleitung

Wet Sounds

Wet Sounds VENUE Series Bedienungsanleitung

Wet Sounds

Wet Sounds XS-650 Bedienungsanleitung

Wet Sounds

Wet Sounds STEALTH 6 Bedienungsanleitung

Wet Sounds

Wet Sounds XS-650 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung