Whadda WPM333 Bedienungsanleitung

USER MANUAL

TB6500 3 A stepper motor driver board

WPM333

whadda.com

Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its

lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted

municipal waste; it should be taken to a specialized company for recycling. This device

should be returned to your distributor or to a local recycling service. Respect the local

environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Whadda! Please read the manual thoroughly before bringing this

device into service. If the device was damaged in transit, do not install or use it and contact

your dealer.

Safety Instructions

Read and understand this manual and all safety signs before using this appliance.

For indoor use only.

•This device can be used by children aged from 8 years and above, and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning the use of the device in a

safe way and understand the hazards involved. Children shall not play with the device.

Cleaning and user maintenance shall not be made by children without supervision.

General Guidelines

•Refer to the Velleman®Service and Quality Warranty on the last pages of this manual.

•All modifications of the device are forbidden for safety reasons. Damage caused by

user modifications to the device is not covered by the warranty.

•Only use the device for its intended purpose. Using the device in an unauthorized way

will void the warranty.

•Damage caused by disregard of certain guidelines in this manual is not covered by the

warranty and the dealer will not accept responsibility for any ensuing defects or

problems.

•Nor Velleman Group nv nor its dealers can be held responsible for any damage

(extraordinary, incidental or indirect) –of any nature (financial, physical…) arising from

the possession, use or failure of this product.

•Keep this manual for future reference.

What is Arduino®

Arduino®is an open-source prototyping platform based on easy-to-use hardware and

software. Arduino®boards are able to read inputs –light-on sensor, a finger on a button or a

Twitter message –and turn it into an output –activating of a motor, turning on an LED,

publishing something online. You can tell your board what to do by sending a set of

instructions to the microcontroller on the board. To do so, you use the Arduino

programming language (based on Wiring) and the Arduino®software IDE (based on

Processing). Additional shields/modules/components are required for reading a twitter

message or publishing online. Surf to www.arduino.cc for more information.

Specifications

•operating voltage: 10-35 VDC

•rated output current: ± 3 A - peak 3.5 A

•dimensions: 50 x 75 x 35 mm

•weight: 80 g

Features

•6N137 high-speed OptoCouple to ensure high-speed without losing steps

•for 42,57,86 stepper within 3 A 2/4-phase/4-wire /6-wire stepper motor

•automatic half-decay

•excitation mode: synchronizing, half step, 1/8 step, 1/16 step

•current level is adjustable to meet your application needs

•large heat sink for good heat dissipation

•overheating and over-current protection circuit to ensure optimal performance

Pin Layout

terminal

description

EN+ EN-

enable positive/negative

CW+ CW-

direction control

CLK+ CLK-

pulse signal control

24+ GND

power supply

A+ A-

motor A (red/blue wire)

B+ B-

motor B (green/black wire)

controller:

TB6560

MCU, PLC, digital circuits

driver board

Note: Resistors on data lines are optional.

Example

Connection to Arduino® UNO

Arduino®

WPM333

GND

EN+

GND

EN-

CW+

GND

CW-

CLK+

GND

CLK-

Connection to 4-Wire Stepper Motor

Stepper Motor

WPM333

red wire

A+

blue wire

A-

green wire

B+

black wire

B-

Whadda WPM333 Stepper Motor Driver Arduino example

This example shows how the Whadda WPM333 Stepper Motor Driver board can be used

with Arduino.

The following connections are required:

2 <==> CW+

GND <==> CW-

3 <==> CLK+

GND <==> CLK-

For more information about the Whadda WPM333 Stepper Motor Driver, consult the

manual, available online at whadda.com

Example program based on TB6560 Arduino example code from makerguides.com

(https://www.makerguides.com/tb6560-stepper-motor-driver-arduino-tutorial/)

#define CW_Pin 2

#define CLK_Pin 3

#define stepsPerRevolution 200

void setup() {

// Declare pins as output:

pinMode(CW_Pin, OUTPUT);

pinMode(CLK_Pin, OUTPUT);

}

void loop() {

// Set the spinning direction clockwise:

digitalWrite(CW_Pin, HIGH);

// Spin the stepper motor 1 revolution slowly:

for (int i = 0; i < stepsPerRevolution; i++) {

// These four lines result in 1 step:

digitalWrite(CLK_Pin, HIGH);

delayMicroseconds(8000);

digitalWrite(CLK_Pin, LOW);

delayMicroseconds(8000);

}

delay(1000);

// Set the spinning direction counterclockwise:

digitalWrite(CW_Pin, LOW);

// Spin the stepper motor 1 revolution quickly:

for (int i = 0; i < stepsPerRevolution; i++) {

// These four lines result in 1 step:

digitalWrite(CLK_Pin, HIGH);

delayMicroseconds(4000);

digitalWrite(CLK_Pin, LOW);

delayMicroseconds(4000);

}

delay(1000);

// Set the spinning direction clockwise:

digitalWrite(CW_Pin, HIGH);

// Spin the stepper motor 5 revolutions fast:

for (int i = 0; i < 5 * stepsPerRevolution; i++) {

// These four lines result in 1 step:

digitalWrite(CLK_Pin, HIGH);

delayMicroseconds(2000);

digitalWrite(CLK_Pin, LOW);

delayMicroseconds(2000);

}

delay(1000);

// Set the spinning direction counterclockwise:

digitalWrite(CW_Pin, LOW);

// Spin the stepper motor 5 revolutions fast:

for (int i = 0; i < 5 * stepsPerRevolution; i++) {

// These four lines result in 1 step:

digitalWrite(CLK_Pin, HIGH);

delayMicroseconds(2000);

digitalWrite(CLK_Pin, LOW);

delayMicroseconds(2000);

}

delay(1000);

}

The running current limit can be set by using the DIP-switches located on the module. The

following table gives an overview of the possible settings.

whadda.com

Modifications and typographical errors reserved - © Velleman Group nv. WPM333_v01

Velleman Group nv, Legen Heirweg 33 - 9890 Gavere.

Inhaltsverzeichnis

Andere Whadda Computerhardware Handbücher

Whadda

Whadda WPSH203 Bedienungsanleitung

Whadda

Whadda RFM69HCW Bedienungsanleitung

Whadda

Whadda SERVO-MG995 Bedienungsanleitung

Whadda

Whadda WPSE475 Bedienungsanleitung

Whadda

Whadda RFM69HCW Bedienungsanleitung

Whadda

Whadda VM167 Bedienungsanleitung

Whadda

Whadda WPM449 Bedienungsanleitung

Whadda

Whadda WPI304N Bedienungsanleitung

Whadda

Whadda NEO-6M GPS SHIELD FOR RASPBERRY PI Bedienungsanleitung

Whadda

Whadda WPSH205 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung