Whelen Engineering Company WeCan Series Bedienungsanleitung

Page 1

Form No.14157A (081709) For warranty information regarding this product, visit www.whelen.com/warranty

Automotive: Serial Communications

Installation Guide:

Control Point Module

for WeCan® Lightbars

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Internet: www.whelen.com

Sales e-mail: autosale@whelen.com

Customer Service e-mail: [email protected]

ENGINEERING COMPANY INC.

WARNING: This product can expose you to chemicals including Lead which is known to the State of California to cause cancer and birth defects or

other reproductive harm. For more information go to www.P65Warnings.ca.gov.

USB

Port

*NOTE: Apply +12VDC to the WHT/GRN

and WHT/YEL wires simultaneously for

split Traffic Advisor.

DEFAULT CONFIGURATION (12V Inputs)

COLOR

GREEN

GRN/WHT

GRN/BLK

WHT/RED

WHITE

YELLOW

WHT/VIO

WHT/GRN

WHT/ORG

BLUE

BLU/WHT

BLU/BLK

WHT/BRN

WHT/BLK

WHT/BLU

RED/WHT

WHT/YEL

VIOLET

FUNCTION

FRONT PATTERN 1

FRONT PATTERN 2

FRONT PATTERN 3

FRONT PATTERN 4

DRIVER ALLEY

PASSENGER ALLEY

AUX

RIGHT TRAFFIC ADVISOR

CRUISE LIGHTS

REAR PATTERN 1

REAR

TAKE DOWNS

FLASHING TAKE DOWN / ALLEY

OVERRIDE

LEFT TRAFFIC ADVISOR

LOW POWER

™

PATTERN 2

PATTERN 3

PATTERN 4

STEADY

POS

Connect to an ignition controlled

circuit that can accommodate an

additional 250mA load.

from lightbar

LIGHTBAR CABLE CONNECTOR

COLOR

RED

None

BLACK

GREEN

BLK/WHT

GREY

FUNCTION

+12VDC

GROUND

COMM. A

SHIELD

COMM. B

POS

Overview -

The Control Point Module serves as the ‘brains’ of the

Whelen WC Series lightbar. The module is programmed with

the WeCan™ Programming Software via the USB port and in

turn, provides the necessary signals that allow the lightbar to

function in the desired manner.

As represented in the WeCan™ Programming software, each

of the 18 inputs may be programmed to activate any number

or combination of the installed lightbar components. This is

accomplished by applying +12VDC to an input. Refer to the

sample wiring diagrams shown on pgs. 2 through 4, or the

installation guide included with your switches for detailed

wiring information.

Note - The pattern override feature will override all active

LED lightheads with the pattern override flash pattern.

Programming Procedure -

IMPORTANT - It is not necessary to program this device

unless changes to the default configuration (for example

pattern or switch control changes) are desired.

1. Connect a USB cable from the host PC to the module’s

USB port.

2. Start the WeCan software on the host PC and open the

configuration to be programmed.

3. Click on the “WeCan” button on the menu bar. Select

“Control Point” then “Program” from the fly-out.

4. A window will open to confirm that you are about to

program a Control Point Module. Confirm that the USB

cable is connected to both the module and the PC and

then press “OK” to continue. The software will display a

window when the programming procedure has been

successfully completed.

5. Confirm proper operation of the module.

Page 2

Example #1: Typical CenCom™ layout. Consult your CenCom manual before making any changes to this circuit.

1234567812345678

123

91234

3366

9912

8811

7710

WHITE

FUNCTION

Stand-by

Radio Repeat

Hands-Free

Wail

Yelp

Tone 3

Manual

Air Horn

Cruise

Horn Transfer Relay*

Low Power

Take down

Driver Alley

Passenger Alley

Override

Gun Lock*

All

External TA (if applicable)

Steady

Rear

Front

+ Flashing Take-downs

BUTTON

SS1

SS2

SS3

1234

*see your CenCom manual for details

COLOR

RED

ORG

N/C

WHT/BRN - Programable Input 1*

WHT/ - Programable Input 2*

WHT/ - Programable Input 3*

WHT/YEL - Programable Input 4*

BRN - Outlet 9 (250mA MAX)

RED - Outlet 10 (250mA MAX)

ORG - Outlet 11 (250mA MAX)

YEL - Outlet 12 (250mA MAX)*

POS

TYCO-P&B P/N:

VF4-45F11

Car

Horn

From Vehicle

Horn Relay

Horn Ring

Transfer Relay

(Customer Supplied)

Outlet

#12

Input

87A

Outlet 2 (20A MAX)

Outlet 1 (40A MAX)

Outlet 3 (20A MAX)

Connector A

Connector E

Connector D

Connector B (Blue)

Connector C (Green)

COLOR

BR N Output 8

RED

ORG

N/C

BLU

N/C

OW -

Isolated Relay - N.O. (10A MAX)

- Output 8

Isolated Relay - N.C. (10A MAX)*

- Output 8

Isolated Relay - Com. (10A MAX)*

GRN - Outlet 7 (10A MAX)

- Outlet 6 (10A MAX)

VIO - Outlet 5 (10A MAX)

GRY - Outlet 4 (10A MAX)

POS

*see your CenCom manual for details

COLOR

GREEN

GRN/WHT

GRN/BLK

WHT/RED

WHITE

YELLOW

WHT/VIO

WHT/GRN

WHT/ORG

FUNCTION

FRONT PATTERN 1

FRONT PATTERN 2

FRONT PATTERN 3

FRONT PATTERN 4

DRIVER ALLEY

PASSENGER ALLEY

AUX

RIGHT TRAFFIC ADVISOR

CRUISE LIGHTS

Connects to CenCom...

Connector

D - PIN#7 (VIO)

D - PIN#6 (BLU)

E - PIN#5 (BRN)

Optional

Connector

ptional

Connector

POS

COLOR

BLUE

BLU/WHT

BLU/BLK

WHT/BRN

WHT/BLK

WHT/BLU

RED/WHT

WHT/YEL

VIOLET

FUNCTION

REAR PATTERN 1

REAR

TAKE DOWNS

FLASHING TD / ALLEY

PATTERN OVERRIDE

LEFT TRAFFIC ADVISOR

LOW POWER

PATTERN 2

PATTERN 3

PATTERN

Connects to CenCom...

Connector

Connector D - PIN#5 (GRN)

OPTIONAL

Connector

Optional

D - PIN#8 (GRY)

Connector C

E - PIN#6 (RED)

POS

LIGHTBAR

Communication

Cable

Power

Cable

Pos. 1 - (GRN) Front Pattern 1

Pos.10 - (BLU) Rear Pattern 1

Pos. 2 - (GRN/WHT) Front Pattern 2

Pos.11 - BLU/WHT) Rear Pattern 2

Pos. 3 - (GRN/BLK) Front Pattern 3

Pos.12 - (BLU/BLK) Rear Pattern 3

Pos. 4 - (WHT/RED) Front Pattern 4

Pos.13 - (WHT/BRN) Rear Pattern 4

Pos. 5 - (WHT) Driver Alley Light

Pos.14 - (WHT/BLK) Take-downs

Pos. 6 - (YEL) Passenger Alley Light

Pos.15 - (WHT/BLU) Flashing TD & Alley

Pos. 7 - (WHT/VIO) Aux

Pos.16 - (RED/WHT) Steady Override

Pos. 8 - (WHT/GRN) Traffic Advisor / RIGHT

Pos.17 - WHT/YEL) Traffic Advisor™ / LEFT

Pos. 9 - (WHT/ORG) Cruise Light

Pos.18 - (VIO) Low Power

987654321

18 17 16 15 14 13 12 11 10

321

654

Connect to an ignition

controlled circuit that

can accommodate an

additional 250mA load.

Pos. 1 - (RED) To +12VDC*

Pos.2-NoConnection

Pos. 3 - (BLK) To Ground

Pos. 4 - (GRN) COMM. A

Pos. 5 - (BLK/WHT) Shield

Pos. 6 - (GRY) COMM. B

RED - to +12VDC

(see lightbar manual for fusing)

BLACK - to CHASSIS GROUND

Page 3

Example #2: Integrating a WeCan® Control Point Module into a 295SLS*6 System.

FUNCTION

Take-downs

Driver Alley Light

Passenger Alley Light

Traffic Advisor™ Left

Traffic Advisor Right

Low Power

Rear

Front + Rear

Front + Rear + Flashing Take-Downs

BUTTON

PB1

PB2

PB3

PB4

PB5

PB6

SS1

SS2

SS3

FUNCTION

Slide Switch #1

Slide Switch #2

Slide Switch #3

Push Button #1

Push Button #2

Push Button #3

Push Button #4

Push Button #5

Push Button #6

TERMINAL

PB#1

Activates

Terminal

PB#2

Activates

Terminal

PB#3

Activates

Terminal

PB#4

Activates

Terminal

PB#5

Activates

Terminal

10, 11, 12

PB#6

Activates

Terminal

13, 14, 15

MAN

RAD

HORN

RAD

MAN 1

MAN 2

SPEAKERS

MIC VOL.

20 Amp Fuse

123456789101112131415

(TERMINALS)

COLOR

GREEN

GRN/WHT

GRN/BLK

WHT/RED

WHITE

YELLOW

WHT/VIO

WHT/GRN

WHT/ORG

FUNCTION

FRONT PATTERN 1

FRONT

DRIVER ALLEY

PASSENGER ALLEY

AUX

RIGHT TRAFFIC ADVISOR

CRUISE LIGHTS

PATTERN 2

PATTERN 3

PATTERN 4

Connects to...

Terminal

T 7 (PB#2)

T 8 (PB#3)

T 10 (PH#5)

OPTIONAL

2 (SS#2)

Optional

erminal

ptional

erminal

POS

COLOR

BLUE

BLU/WHT

BLU/BLK

WHT/BRN

WHT/BLK

WHT/BLU

RED/WHT

WHT/YEL

VIOLET

FUNCTION

REAR

TAKE DOWNS

FLASHING TD / ALLEY

OVERRIDE

LEFT TRAFFIC ADVISOR

LOW POWER

PATTERN 1

PATTERN 2

PATTERN 3

PATTERN 4

STEADY

Connects to...

Terminal 1 (SS#1)

Optional

Terminal 6 (PB#1)

Terminal 3 (SS#3)

Optional

Terminal 9 (PB#4)

Terminal 13 (PB#6)

POS

LIGHTBAR

Communication

Cable

Power

Cable

Pos. 1 - (GRN) Front Pattern 1

Pos.10 - (BLU) Rear Pattern 1

Pos. 2 - (GRN/WHT) Front Pattern 2

Pos.11 - BLU/WHT) Rear Pattern 2

Pos. 3 - (GRN/BLK) Front Pattern 3

Pos.12 - (BLU/BLK) Rear Pattern 3

Pos. 4 - (WHT/RED) Front Pattern 4

Pos.13 - (WHT/BRN) Rear Pattern 4

Pos. 5 - (WHT) Driver Alley Light

Pos.14 - (WHT/BLK) Take-downs

Pos. 6 - (YEL) Passenger Alley Light

Pos.15 - (WHT/BLU) Flashing T-D & Alley

Pos. 7 - (WHT/VIO) Aux

Pos.16 - (RED/WHT) Steady Override

Pos. 8 - (WHT/GRN) Traffic Advisor / RIGHT

Pos.17 - WHT/YEL) Traffic Advisor / LEFT

Pos. 9 - (WHT/ORG) Cruise Light

Pos.18 - (VIO) Low Power

987654321

18 17 16 15 14 13 12 11 10

321

654

Connect to an ignition

controlled circuit that

can accommodate an

additional 250mA load.

Pos. 1 - (RED) To +12VDC*

Pos.2-NoConnection

Pos. 3 - (BLK) To Ground

Pos. 4 - (GRN) COMM. A

Pos. 5 - (BLK/WHT) Shield

Pos. 6 - (GRY) COMM. B

RED - to +12VDC

(see lightbar manual for fusing)

BLACK - to CHASSIS GROUND

Page 4

FUNCTION

Take-downs

Driver Alley Light

Passenger Alley Light

Traffic Advisor™ Left

Traffic Advisor Right

Low Power

Rear

Front + Rear

Front + Rear + Flashing Take-Downs

BUTTON

PB1

PB2

PB3

PB4

PB5

PB6

SS1

SS2

SS3

Example #3: Integrating a WeCan® Control Point Module into a PCCS9NP System.

#1 SS

#2 SS

PB1 PB2 PB3 PB4 PB5 PB6

COLOR

GREEN - Slide Switch #1

BROWN -

VIOLET - PB Switch #9 (mom)

BLUE - Slide Switch #3

GRY - Slide Switch #2

WHT - PB Switch #5

YEL - PB Switch #6

ORG - PB Switch #7

WHT/BLK - PB Switch #4

See PCCS9NP manual

POS

COLOR

RED -

BLACK - Chassis Ground

WHT/GRN - To Aux Siren (option)

BLK/WHT - PB Switch #8

WHT/RED - To +12V (backlight)

See PCCS9NP manual

POS

6-POSITION

SOCKET

CONNECTOR

9-POSITION

SOCKET

CONNECTOR

Connector A

Connector B

COLOR

GREEN

GRN/WHT

GRN/BLK

WHT/RED

WHITE

YELLOW

WHT/VIO

WHT/GRN

WHT/ORG

FUNCTION

FRONT PATTERN 1

FRONT

DRIVER ALLEY

PASSENGER ALLEY

RIGHT TRAFFIC ADVISOR

CRUISE LIGHTS

PATTERN 2

PATTERN 3

PATTERN 4

Connects to...

Connector A - Pos. (SS# )

Optional

Connector A - Pos. 6 (PB#2)

Connector A - Pos. 7 (PB#3)

ptional

Connector B - Pos. 4 (SS#5)

Optional

POS

COLOR

BLUE

BLU/WHT

BLU/BLK

WHT/BRN

WHT/BLK

WHT/BLU

RED/WHT

WHT/YEL

VIOLET

FUNCTION

REAR

TAKE DOWNS

FLASHING TD / ALLEY

OVERRIDE

LEFT TRAFFIC ADVISOR

LOW POWER

PATTERN 1

PATTERN 2

PATTERN 3

PATTERN 4

STEADY

Connects to...

Connector A - Pos. 1 (SS#1)

Optional

Connector A - Pos. 9 (PB#1)

ptional

Connector A - Pos. 4 (SS#3)

Connector A - Pos. 8 (PB#4)

Connector A - Pos. 3 (PB#6)

POS

LIGHTBAR

Communication

Cable

Power

Cable

Pos. 1 - (GRN) Front Pattern 1

Pos.10 - (BLU) Rear Pattern 1

Pos. 2 - (GRN/WHT) Front Pattern 2

Pos.11 - BLU/WHT) Rear Pattern 2

Pos. 3 - (GRN/BLK) Front Pattern 3

Pos.12 - (BLU/BLK) Rear Pattern 3

Pos. 4 - (WHT/RED) Front Pattern 4

Pos.13 - (WHT/BRN) Rear Pattern 4

Pos. 5 - (WHT) Driver Alley Light

Pos.14 - (WHT/BLK) Take-downs

Pos. 6 - (YEL) Passenger Alley Light

Pos.15 - (WHT/BLU) Flashing T-D & Alley

Pos. 7 - (WHT/VIO) Aux

Pos.16 - (RED/WHT) Steady Override

Pos. 8 - (WHT/GRN) Traffic Advisor / RIGHT

Pos.17 - WHT/YEL) Traffic Advisor / LEFT

Pos. 9 - (WHT/ORG) Cruise Light

Pos.18 - (VIO) Low Power

987654321

18 17 16 15 14 13 12 11 10

321

654

Connect to an ignition

controlled circuit that

can accommodate an

additional 250mA load.

Pos. 1 - (RED) To +12VDC*

Pos.2-NoConnection

Pos. 3 - (BLK) To Ground

Pos. 4 - (GRN) COMM. A

Pos. 5 - (BLK/WHT) Shield

Pos. 6 - (GRY) COMM. B

RED - to +12VDC

(see lightbar manual for fusing)

BLACK - to CHASSIS GROUND

Andere Whelen Engineering Company Steuereinheit Handbücher

Whelen Engineering Company

Whelen Engineering Company BETA1 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WPA Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company CanTrol Fehlerbehebungshandbuch

Whelen Engineering Company

Whelen Engineering Company CenCom Core-S C399S Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company CenCom Core C399 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295SDA1 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WPKM1 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company CenCom Core C399 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company E-2010 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company CenCom Core-R CEM4HC Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WeCanX V2V Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company PCC4W Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295HFSA6 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company PCCS9NP Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung