Whirlpool AS12 Bedienungsanleitung

Preparation before use

The remote controller is NOT presetting as Cooling Only Air Conditioner or Heat Pump by manufacturer.

User can preset the remote controller type depending on the air conditioner type you have purchased

as follows:

Each time after the remote controller replaces batteries or is energized, the Cooling indicator and

Heating indicator will flashes alternately on LCD of the remote controller.

Press any button when flashes, Heat Pump is set.

Note:

If the air conditioner you purchased is a Cooling Only one, but you preset the remote controller as Heat Pump, it doesn't

bring any matter. But if the air conditioner you purchased is a Heat Pump one, and you preset the remote controller as

Cooling Only, then you CAN NOT preset the Heating operation with the remote controller.

Press any button when flashes, Cooling Only is set.

If you don't press any button within 12 seconds, the remote controller is preset as Heat Pump automatically.

If you want auto restart function,let the appliance is energized, hold down the Emergency

button (ON/OFF) on the indoor unit for over 5 seconds, auto restart function is set with buzz sound,

air conditioner is on standby.

If auto restart has been set, hold down the Emergency button (ON/OFF) on the indoor unit for over 5

seconds, auto restart function is canceled with buzz sound, air conditioner is on standby.

Remote Controller presetting

Before using the air conditioner, be sure to check and preset the following.

Auto Restart Presetting

Hold down any button of remote controller for about 2 seconds, back-light turns on. Release the button,

it lights off automatically 10 seconds later.

Note: Back-light is an optional function.

Back-light function (optional)

FAN

MODE

TIMERON

CLOCK

TIMER

OFF

SLEEP

SWING

ONON

OFFOFF

JET

SMART

LOCK

Safety precautions

Symbols in this Use and Care Manual are interpreted as shown below.

Be sure not to do.

The feature of the appliance,

instead of a fault.

Pay attention to such a situation.

Grounding is essential.

Be sure to follow this instruction.

Do not use the power supply circuit

breaker or pull off the plug to turn it off

during operation. This may cause a fire

due to spark, etc.

Keep the power supply circuit breaker

or plug from dirt. Connect the power

supply cord to it firmly and correctly,

lest an electric shock or a fire break out

due to insufficient contact.

Use correct power supply in

accordance with the rating plate

requirement. Otherwise, serious

faults or hazard may occur or a

fire maybe break out.

Do not knit, pull or press the power supply

cord, lest the power supply cord be broken.

An electric shock or fire is probably caused

by a broken power supply cord.

Never insert a stick or similar obstacle

to the unit. Since the fan rotates at high

speed, this may cause an injury.

Do not repair the appliance by yourself.

If this is done incorrectly, it may cause an

electric shock, etc.

Turn off the appliance by remote control

firstly before cutting off power supply if

malfunction occurs.

It is harmful to your health if the cool air

reaches you for a long time. It is advisable

to let the air flow be deflected to all the room.

Prevent the air flow from reaching the gas

burners and stove.

Do not touch the operation buttons

when your hands are wet.

Do not put any objects on the outdoor

unit.

It is the user's responsibility to make the

appliance be grounded according to

local codes or ordinances by a licenced

technician.

OFF OFF

Warning: Incorrect handling could

cause a serious hazard, such as death,

serious injury, etc.

The figures in this manual are based on the external view of a standard model.

Consequently, the shape may differ from that of the air conditioner you have selected.

Air Intake

Air Outlet

Louver

Vertical Adjustment

Louver

Horizontal Adjustment

Air Filter

Remote Controller

Connection Cord

Pipes and Power

Drain Hose

Front Panel

Emergency Panel

Display Panel

Note: Condensate water drains

at COOLING or DRY operation.

Identification of parts

Indoor unit

Outdoor unit

FAN

MODE

TIMERON

CLOCK

TIMER

OFF

SLEEP

SWING

ONON

OFF

JET

SMART

LOCK

The shape and position of the switches and indicators may vary from different models, but their function are similar.

Identification of parts

It lights up during the

set time.

It lights up when

compressor is running.

It is on during operation.

It flashes during

defrosting.

Timer Indicator

Compressor indicator

Run Indicator

Sleep Indicator

UH series operating and display

It lights up when

unit is in sleep mode.

Temperature display

Display actual room

temperarure.

Display set temperature.

FAN

MODE

TIMER ON

CLOCK

TIMER OFF

SLEEP

SWING

ONON

OFFOFF

sense

LOCK

The remote controller transmits signals to the system.

Remote controller

10 BUTTON

SWING BUTTON

FAN BUTTON

ROOM TEMPERATURE

SETTING BUTTONS

SLEEP BUTTON

LOCK BUTTON

CLOCK BUTTON

ON/OFF BUTTON

BUTTON

MODE BUTTON

TIMER ON/OFF BUTTON Used to start or stop the fast cooling.

(Fast cooling operates at high fan speed with

18 C set temp automatically )

Used to stop or start vertical adjustment

louver swinging and set the desired up/down

airflow direction.

Used to select fan speed in sequence

auto, high, medium or low.

Used to set or cancel Sleep Mode operation.

When you press this button, all the buttons

are locked and not available. Press again to

cancel it.

Used to set the current time.

Used to enter fuzzy logic operation directly,

regardless of the unit is on or off.

The appliance will be started when it is

energized or will be stopped when it is

in operation, if you press this button.

Press this button to select the operation mode.

Used to set or cancel the timer operation.

Remote controller

Indication symbols on LCD:

Note: Each mode and relevant function will be further specified in following pages.

Signal transmit.

Dry indicator

Fan only indicator

Heating indicator

Cooling indicator

High fan speed

Medium fan speed

Low fan speed Display set temperature

Display set timer

Display current time

Auto fan speed 6th sense indicator

Sleep indicator

Lock indicator

Jet indicator

ONON

OFFOFF

Used to adjust the room temperature and

the timer, also real time.

sense

How to Insert the Batteries

How to Use

Remove the battery cover according to the arrow direction.

Insert new batteries making sure that the (+) and (-) of

battery are matched correctly.

Reattach the cover by sliding it back into position.

Note:

Use 2 LR03 AA(1.5volt) batteries. Do not use rechargeable batteries.

Replace batteries with new ones of the same type when the display

becomes dim.

Storage and Tips for Using the Remote Controller

The remote controller may be stored mounted on a wall with a holder.

Note: The remote controller holder is an optional part.

To operate the room air conditioner, aim

the remote controller to the signal receptor.

The remote controller will operate the air

conditioner at a distance of up to 7m when

pointing at signal receptor of indoor unit.

Choose Cooling Only Remote controller or Heat Pump

Please refer to page 1 " Preparation before use" for details.

Signal receptor

Remote controller

If the replacement is done within 1 minute, the remote controller

will keep original presetting. However, if you want to change the

presetting from Heat Pump to Cool Only or Cool Only to Heat Pump,

you should reload batteries 3 minutes after removing the old ones.

(Please refer to page 1 for details.)

FAN

MODE

OFFOFF

FAN

MODE

TIMERON

CLOCK

LOCK

TIMER

OFF

SLEEP

SWING

SMART

SUPER

OFFOFF

FANFAN

MODE

OFF

FAN

MODE

TIMERON

CLOCK

TIMER OFF

SLEEP

SWING

ONON

OFFOFF

sense

LOCK

Each time MODE button is pressed, the operation mode

is changed in sequence:

Each time the "FAN" button is pressed, the fan speed is

changed in sequence:

18 ~32

Heating mode is NOT available for cooling only air conditioner.

HEATING

COOLING DRY FAN ONLY

Selecting mode

FAN mode

Auto High Medium Low

At "FAN ONLY" mode, only "High","Medium" and "Low" are available.

At "DRY" mode, Fan speed is set at "Low" automatically, "FAN" button

is ineffective in this case.

Setting temperature

Press once to temperature setting by 1lower

Press once to temperature setting by 1raise

Range of available set temperature

*HEATING, COOLING

DRY

FAN unable to set

unable to set

Turning on

SWING, 6th sense, TIMER ON, TIMER OFF, CLOCK, SLEEP and Jet operation modes will be

specified in the following pages.

Press button, when the appliance receives the

signal, the RUN indicator of the indoor unit lights up.

Changing modes during operation, sometimes the unit does not response at once. Wait 3 minutes.

Wait 3 minutes before restarting the appliance.

During heating operation, air flow is not discharged at the beginning. After 2 5 minutes, the air flow will be discharged

until temperature of indoor heat exchanger rises.

ONLY

Operation instructions

Operation modes

*Note: Heating mode is NOT available for cooling only models.

Airflow direction control

Vertical airflow is automatically adjusted to a certain angle

in accordance with the operation mode after turning on the unit.

The direction of airflow can be

also adjusted to your own

requirement by pressing the

"SWING" button of the

remote controller.

Operation mode Direction of airflow

COOLING, DRY

*HEATING,

FAN ONLY

horizontal

downward

Vertical airflow control (with the remote controller)

Using remote controller to set various angles of flow or specific angle

as you like.

Swinging airflow

Pressing "SWING" button once, the vertical adjustment

louver will swing up and down automatically.

Desired direction airflow

Pressing the "SWING" button again when the louvers swing

to a suitable angle as desired.

Horizontal airflow control (with hands)

Turning the control rods of the

horizontal adjustment louvers to

change horizontal air flow as shown.

control rods of horizontal

adjustment louvers

Note: The shape of the unit may look different

from that of the air conditioner you have selected.

Do not turn the vertical adjustment louvers manually, otherwise malfunction may occur. If that happens, turn off the unit

first and cut off the power supply, then restore power supply again.

It is better not to let the vertical adjustment louver tilt downward for a long time at COOLING or DRY mode to prevent

condensed water from dripping.

Operation instructions

*Heating mode is only available for heat pump models.

Airflow direction control

SWING

FAN

MODE

TIMERON

CLOCK

TIMER

OFF

SLEEP

SWING

ONON

OFFOFF

sense

LOCK

Indoor temperature

Button is ineffective in Jet mode.

Target temperature

21 or below

26 or below

2222

Over 26

21 -23

23 -26

Your feeling

What you can do in 6th sense mode

button adjustment procedure

Operation mode

HEATING

FAN ONLY

DRY

Room temperature

decrease 1.5 after

operate for 3 minutes

Room temperature

decrease 1.5 after

operate for 3 minutes

COOLING

Press the button, the unit enters 6th sense mode(fuzzy logic operation) directly regardless of

the unit is on or off. In this mode, temperature and fan speed are automatically set based on the

actual room temperature.

Uncomfortable

because of

unsuitable air

flow volume.

Uncomfortable

because of

unsuitable flow

direction.

Indoor fan speed alternates among

High, Medium and Low each time this

button is pressed.

Press it once, the vertical adjustment

louver swings to change vertical airflow

direction. Press it again, swings stops.

For horizontal airflow direction, please

refer to the previous page for details.

Operation mode and temperature are determined by indoor temperature

Note: Temperature, airflow and direction are controlled automatically in 6th mode.

However, a decrease or rise of up to 2 can be set with the remote controller if you still

feel uncomfortable.

Operation instructions

6th sense mode

Heat pump models

Cooling only models

FAN

SWING

CLOCK button

You can adjust the real time by pressing CLOCK button, then

using and buttons to get the correct time, press

CLOCK button again the real time is set.

sense

FAN

MODE

TIMER ON

CLOCK

TIMER OFF

SLEEP

SWING

ONON

OFFOFF

sense

LOCK

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Whirlpool Klimaanlage Handbücher

Whirlpool

Whirlpool 1188177-W Stücklistenhandbuch

Whirlpool

Whirlpool AMD034 Bedienungsanleitung

Whirlpool

Whirlpool ACQ142XA0 Bedienungsanleitung

Whirlpool

Whirlpool Comfore-aire RA51K0 Bedienungsanleitung

Whirlpool

Whirlpool AC1052XS Bedienungsanleitung

Whirlpool

Whirlpool ACSL02XT Bedienungsanleitung

Whirlpool

Whirlpool WHAT081-HAW Bedienungsanleitung

Whirlpool

Whirlpool AMD 017 Bedienungsanleitung

Whirlpool

Whirlpool ACC082XR0 Bedienungsanleitung

Whirlpool

Whirlpool BHAC1000XS0 Bedienungsanleitung

Whirlpool

Whirlpool ACP102PR0 Bedienungsanleitung

Whirlpool

Whirlpool ACQL128XS0 Bedienungsanleitung

Whirlpool

Whirlpool ACU088PR0 Bedienungsanleitung

Whirlpool

Whirlpool 63851339 Montageanleitung

Whirlpool

Whirlpool AMD 313 Bedienungsanleitung

Whirlpool

Whirlpool ACM 152XE0 Bedienungsanleitung

Whirlpool

Whirlpool BHAC0600BS0 Bedienungsanleitung

Whirlpool

Whirlpool 1188177 Bedienungsanleitung

Whirlpool

Whirlpool AMAP151BW Bedienungsanleitung

Whirlpool

Whirlpool AC1 352 Bedienungsanleitung

Whirlpool

Whirlpool MAGICOOL Bedienungsanleitung

Whirlpool

Whirlpool SPIW409A2WF Bedienungsanleitung

Whirlpool

Whirlpool PACHW2900CO Bedienungsanleitung

Whirlpool

Whirlpool AI2209 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung