Whirlpool EZ CONNECT Bedienungsanleitung

PART NO. W10363267 Rev. B www.whirlpool.com

Installation

Home Appliances

GUIDE

Table of Contents

(complete) ................... 2

Requesting Assistance

or Service .......................2

Important Information ... 3

Before You Begin .......... 4

Installing the

Ice Maker ........................5

Installing the

Water Line ...................... 7

Final Installation ...........13

Starting the

Ice Maker .......................15

Troubleshooting ...........16

EZ CONNECT ICE MAKER KIT

Table of

Contents

Page

Requesting Assistance or Service ........... 2

Important Information ................................. 3

Before You Begin ....................................... 4

Tools ........................................................ 4

Installation notes...................................... 4

Components ............................................ 4

Installing the Ice Maker.............................. 5

Making preparations ................................ 5

Mounting the ice maker ........................... 6

Page

Routing the copper tubing ....................... 8

Installing the shut-off valve ...................... 9

Connecting the copper tubing

to the shut-off valve ............................... 10

Connecting the copper tubing

to the water valve................................... 11

Turning the water on.............................. 12

Final Installation ....................................... 13

Installing the access cover and

forming the copper tubing ...................... 13

Connecting the power/

leveling the unit...................................... 14

Starting the Ice Maker .............................. 15

Troubleshooting ....................................... 16

Operational notes .................................. 16

Troubleshooting chart ............................ 16

The modular ice maker service sheet.... 17

Ice maker replacement parts list............ 18

Requesting

Assistance or

Service

If you need assistance, contact your dealer,

or call the Whirlpool Consumer Assistance

Center toll-free, 1-800-253-1301, 24 hours a

day.

Installing the Water Line ........................... 7

Choosing a location ................................ 7

Important Information

The following information is used throughout this Installation Guide. Read it carefully so you

are familiar with it.

•DO NOT USE PIERCING-TYPE, OR 3⁄16

SHUT-OFF VALVES. They reduce the flow

of water to the ice maker, and are easily

clogged.

•DO NOT USE POLYETHYLENE TUBING

to connect the ice maker to the water line.

Use only 1⁄4

(O.D.) copper tubing.

CUSTOMER INSTALLATION IS NOT

WARRANTED BY THE REFRIGERATOR

OR ICE MAKER MANUFACTURER.

•This Installation Guide gives you complete

instructions on how to install the Ice Maker

Kit in your refrigerator-freezer and connect

a water line to it. Please read the guide

carefully and follow the instructions exactly

as described. Also, make sure that you

observe all of the “safety” instructions.

•This kit is designed so that almost anyone

can install it; however, a certain amount of

mechanical ability is required.

•Before you start to install your Ice Maker

Kit, you will have to purchase a copper

tubing kit that contains a “Regular Valve

and Clamp Assembly” (for refrigerators with

an automatic ice maker, or self-filling trays).

The kit contains all of the hardware

necessary to connect your ice maker to the

water supply. You can purchase one at

most hardware or plumbing supply stores.

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or

“WARNING.” These words mean:

Before You Begin

Tools

Gather required tools and parts before

starting installation. Read and follow the

instructions provided with any tools listed here.

1. Regular screwdriver

2. Phillips screwdriver

3. 7»16

and 1»2

open-end wrenches (or an

adjustable wrench)

4. Pliers

5. 1»4

nut driver

6. Hand drill with 1»4

drill bit

7. Small hand level (optional)

8. Small 3»4-round file

9. Tubing cutter

10.Center punch

11.Hammer

12.Scissors

13.Ruler

14.Step stool (optional)

Installation notes

1.Follow all of the instructions. Read

through the entire step so that you

understand it before you perform it.

2.The illustrations in this Installation Guide

are meant to clarify the installation steps

you need to perform. For each set of steps

shown, refer to the diagram immediately

beside or below the text for clarification.

Some illustrations also contain “DETAILS.”

DETAILS are contained in bubbles

alongside the larger illustration. A DETAIL

shows a close-up illustration of a certain

portion of a diagram or an illustration of a

specific step you are to perform. DETAILS

are labeled A, B, C or D and are clearly

referenced in each step.

3.When you are instructed to install a part,

position the part as shown in the illustration.

BEFORE

Components

Remove the contents from the shipping carton

and set them on a table where they can be

easily identified and located. Check all of the

components in the kit against the following list

to help you become familiar with them. When

you identify a component, place a check

mark ( 3) after it. The KEY numbers

correspond to the “Component Illustrations.”

Do not discard any of the packing material

until you account for all of the components. If

you need to order a replacement part for the

Ice Maker, a replacement parts list is provided

on page 18.

KEY QTY. DESCRIPTION

1 1 Ice maker

2 1 Ice bucket

COMPONENT ILLUSTRATIONS

Installing the Ice Maker

Making preparations

Refer to the illustration below for the

following steps.

1.Pull the refrigerator away from the wall so

that you can easily access the rear panel. 5.

Electrical Shock Hazard

Disconnect power before installing

ice maker.

Failure to do so could result in death or

electrical shock.

WARNING

2.Unplug Refrigerator or disconnect power.

IMPORTANT:Make sure to protect the floor

from any damage.

3.Open the freezer door and remove all of

the food items from inside the freezer

compartment.

NOTE: The work area for refrigerator-freezer

is shown in DETAIL A below.

You will be

working in

these areas

left side

of freezer

compartment

Work area

Power

cord

plug and

receptacle

Rear wall

Detail A

On top-mount models without a full-width

freezer shelf, remove the ice tray shelf.

Place the shelf aside, as you will use it

later to support the ice bucket.

Remove the screw from the ice maker

connector & tube cover. Retain this

screw for ice maker installation.

Screw

Connector &

Tube Cover

Removing connector & tube cover

6.Insert the end of a small-bladed screwdriver

under the edge of the ice maker mounting

hole plug in the side of the freezer liner, and

pry it out of its hole. You can discard the plug.

Mounting

Hole Plug

Shoulder Screws

NOTE: Verify the shoulder screws are in position.

Refer to the side diagrams for the following

steps.

7.Position the ice maker inside the freezer

compartment and connect its wiring

connector to the wiring harness connector

so they lock together (the locking arm will

snap over the raised tab). The connectors

will fit together only one way.

8.Hang the ice maker from the tabs on the

shoulder screws shown earlier. Make

sure that the bracket mounting hole

is aligned with the mounting hole in

the freezer liner.

9.Mount the ice maker to the freezer liner

mounting hole with the1»2

sheet-metal screw removed from the

ice maker connector & tube cover.

hex-head

Mounting the ice maker

Bracket

Mounting Hole

NOTE: Guide fill tube into water cup hole.

Mounting the Ice Maker

Connectors

Water cup

Installing the Water Line

Choosing a location

1. Open the copper tubing kit that you

purchased earlier, and lay the contents

neatly on a table where you can identify

them easily. The parts from the kit that you

will use are as follows:

1 Regular Valve (not the steel-

piercing type)

2 Compression Sleeves

2 Compression Nuts

2 Clamps

2 Screws

2 Nuts

1 Gasket Seal *

1 Length of Coiled Copper Tubing

* - not needed for 11 Cubic Foot Top Freezer Models (24ECKMF kit)

NOTE: When you work with the soft copper

tubing, be careful not to kink it. If you

accidentally kink the tubing, do not use it.

IMPORTANT: Do not install water line tubing

in a location where the temperature may fall

below freezing; otherwise, property damage

could occur.

2. Choose a suitable water pipe location to

install the water shut-off valve (see side

diagram for some suggested locations). We

recommend installing the valve on a vertical

length of cold (not hot) water pipe that is

nearest your refrigerator. If a vertical length

of pipe is not nearby, you can use a

horizontal length of water pipe, however,

you will have to drill the access hole for the

valve into the top or side of the pipe (not the

bottom). This will keep water in the pipe

from flowing down onto the drill, and also

keep sediment from collecting in the valve

later.

NOTE: Depending on the location of the

horizontal pipe in relation to the floor and

wall, drilling into it may not be possible.

3. Drill a 3⁄8

hole through the floor or wall to

the water pipe.

Through

floor to

basement

cold water

pipe

In crawl

space

under

home to

cold water

pipe

Typical water pipe locations

Under sink

to cold

water pipe

Through

wall to

utility room

cold water

pipe

Routing the copper tubing

Refer to the side diagram for the following

steps.

1. Uncoil the necessary length of copper

tubing and straighten it, then route the end

of the tubing through the access hole you

drilled to the location you have chosen to

install the shut-off valve. Straighten only

enough of the copper tubing to reach this

location. Leave the rest coiled near the

access hole.

2. At this time, make sure that you have been

supplied with enough tubing so that when

you are finished connecting the water line,

you will have enough coiled behind the

refrigerator to easily move it forward far

enough to clean behind it. Also make sure

that the coils are large enough so that when

the unit is pulled forward, the windings will

not stretch too far and kink.

3. Turn off the cold water supply going to the

water pipe where you will be installing the

shut-off valve.

4. Open a cold water tap that is connected to

the selected water pipe and bleed off the

water pressure. Leave the tap open until

after you complete the water line hook up.

5. Use a hammer and a center punch, and

mark the location of the hole for the shut-off

valve. If you are marking copper tubing, do

not strike the punch hard enough to bend it.

6. Install a 1⁄4

bit in the drill, and drill an access

hole through just the front side (not through

both sides) of the cold water pipe.

7. Check the hole and make sure that you

have drilled completely through one side of

the pipe. The edges of the hole should be

smooth and round. If necessary, use a

small 3⁄4-round file to remove any rough

edges from inside the hole, and any burrs

from around the top of the hole.

Routing the copper tubing

Allow 4 to 5 feet of

coiled tubing for

moving refrigerator

Drill 3⁄8" access

hole for tubing

Refrigerator

Back wall Coiled copper

tubing

Water

valve

Drill 1⁄4" hole in

front side of

vertical water

pipe

Installing the shut-off val ve

Refer to the diagram below for the following

steps.

1. Locate the shut-off valve and the front pipe

clamp (with the threaded hole in the center)

from the copper tubing kit. Then, making

sure not to crossthread the valve, screw

the end with the pilot tube into the threaded

hole of the clamp. Hand-tighten the valve

as far as it will go (the threaded shaft is

slightly tapered and can only be tightened

so far).

2. Use a 1⁄2

open-end (or adjustable) wrench,

and turn the body of the shut-off valve an

additional 1⁄8

turn to secure it to the clamp.

3. Slide the rubber seal gasket (from the

copper tubing kit) over the pilot tube (the

unthreaded portion) of the shut-off valve.

Mounting the shut-off valve

to the water pipe

DETAIL A

Screw

Shut-off valve

4. Slide the pilot tube of the shut-off valve

into the water pipe access hole so it is

against the seal gasket, and install the

back pipe clamp over the water pipe.

Secure the clamps to the pipe with the two

screws and nuts that were supplied with

the copper tubing kit. Tighten the nuts

equally so that the space between the

clamps is the same (see DETAIL A). DO

NOT OVERTIGHTEN the nuts, or you

could deform the clamps and damage the

seal gasket.

Keep spacing

equal

Nut

Back pipe

clamp

Seal gasket

Front pipe

clamp

Pilot tube

Vertical cold

water pipe

Connecting the copper tubing to the shut-off valve

Refer to the diagram below for the following

steps.

1.Straighten a 2

section of copper tubing and

make sure that the opening is round and

cut evenly across the end. If necessary, use

a tubing cutter (or a hacksaw) and cut the

end off, then file it so it is even, and remove

any burrs from around the inside and out-

side edges so it is smooth and round. When

you are finished, clean the filings from

inside the tubing as much as possible.

2.Position the compression nut as shown,

and slide it over the end of the copper

tubing.

3.Slide a compression sleeve over the

copper tubing until it is approximately

from the end.

4.Insert the end of the copper tubing into the

outlet connector of the shut-off valve as far

as it will go, and then hand tighten the

compression nut as much as possible.

Connecting the copper tubing to the shut-off valve

5.Use a 1⁄2

open-end wrench, and further

tighten the compression nut on the shut-off

valve

one additional turn

. If necessary, you

will tighten the nut further after you turn on

the water supply.

6.Turn the T-handle on the shut-off valve to

its fully “open” (counterclockwise rotation)

position.

Open

Compression nut

Copper

tubing

Compression

sleeve

Outlet

connector

T-handle

Shut-off

valve

Inhaltsverzeichnis

Sprachen:

Andere Whirlpool Eiswürfelbereiter Handbücher

Whirlpool

Whirlpool 3EHC 50/51-1 Installationsanleitung

Whirlpool

Whirlpool GI15NDXZQ0 Bedienungsanleitung

Whirlpool

Whirlpool AGB 024/01/G/WP Bedienungsanleitung

Whirlpool

Whirlpool GI15NFRT Gebrauchsanweisung

Whirlpool

Whirlpool CHCH8AE Bedienungsanleitung

Whirlpool

Whirlpool GI15NFLTS - Ice Maker Bedienungsanleitung

Whirlpool

Whirlpool 50 Bedienungsanleitung

Whirlpool

Whirlpool CHE-12RC Bedienungsanleitung

Whirlpool

Whirlpool R-66 Bedienungsanleitung

Whirlpool

Whirlpool ECKMF-6 Bedienungsanleitung

Whirlpool

Whirlpool W11390949A Bedienungsanleitung

Whirlpool

Whirlpool GI15NDXZB Bedienungsanleitung

Whirlpool

Whirlpool Automatic Ice Maker Bedienungsanleitung

Whirlpool

Whirlpool GI15NFRTS - Ice Maker Bedienungsanleitung

Whirlpool

Whirlpool AGB 022 Bedienungsanleitung

Whirlpool

Whirlpool WUI95X15HZ Bedienungsanleitung

Whirlpool

Whirlpool GI15NFLTS - Ice Maker Bedienungsanleitung

Whirlpool

Whirlpool GI15NFRTS - INSTALLATION REV A Bedienungsanleitung

Whirlpool

Whirlpool GI15NDXTB1 Bedienungsanleitung

Whirlpool

Whirlpool ECKMF-86 Bedienungsanleitung

Whirlpool

Whirlpool AGH 327/01/G/NE Bedienungsanleitung

Whirlpool

Whirlpool AGS 836 Betriebsanleitung

Whirlpool

Whirlpool GI15NDXTB - 15" 50 lb. Icemaker Bedienungsanleitung

Whirlpool

Whirlpool 2180913 Bedienungsanleitung

Beliebte Eiswürfelbereiter Handbücher anderer Marken

Hoshizaki

Hoshizaki KMD-460MWJ Bedienungsanleitung

Sub-Zero

Sub-Zero 315I Gebrauchsanweisung

Unold

Unold 48945 Bedienungsanleitung

Kenmore

Kenmore 2217402A Bedienungsanleitung

Cornelius

Cornelius WM600 Betriebsanleitung

GE XPIO43SCSS Bedienungsanleitung

Hoshizaki

Hoshizaki KMD-901MAH Bedienungsanleitung

Whynter

Whynter FIM-450HA Bedienungsanleitung

U-Line

U-Line UMCR014-SC01A Installationshandbuch

Andrew James

Andrew James AJ000522 Bedienungsanleitung

Scotsman

Scotsman CME1356 Bedienungsanleitung

Scotsman

Scotsman ACM 25 Bedienungsanleitung

Kärcher

Kärcher IP 120 Bedienungsanleitung

U-Line

U-Line SS1095 Bedienungsanleitung

Maytag

Maytag MIM1554WRS - Ice Maker Bedienungsanleitung

Hoshizaki

Hoshizaki KM-630MAH Bedienungsanleitung

Princess

Princess Yonanas Bedienungsanleitung

Unold

Unold 48946 Bedienungsanleitung