Whirlpool ADN221 C Bedienungsanleitung

ADN221 C

ADN 221

Instruction manual

Instructiuni de utilizare

Instrukcja obsługi

Návod na obsluhu

Mode d’emploi

Manuale d’istruzione











ADN221 C

SAFETY INSTRUCTIONS

CAREFULLY READ THE INSTRUCTION MANUAL. If instructions are not followed,

there is a risk of injury, damage of the appliance and loss of the right to free warranty

service.

The Manufacturer shall not be held liable for damage arising from the failure to observe

the instructions contained in this manual.

We recommend to keep the Instruction manual the whole time you have the appliance.

When you sell the appliance pass the Instruction manual to the new owner of the

appliance.

–Do not cover the ventilation holes at the top and on the sides of the

appliance.

–Do not use electrical appliances inside the food storage compartments of the

appliance, unless they are of the type recommended by the manufacturer.

–If the supply cord is damaged it must be replaced by the manufacturer,

manufacturer service agent or a similarly qualified person, in order to avoid a

hazard.

–Disposal of the appliance should be according to national rules.

–Do not damage the appliance refrigeration system. It contains the refrigerant

gas R600a. If the refrigeration system is damaged:

•Do not use any open flame.

•Avoid sparks ― do not turn on any electrical appliances or lighting

fixtures.

•Immediately ventilate the room.

•Air the room in which the appliance is placed for a few minutes (the

size of the room for a product containing isobuthane / R600a must

be at least 4 m3) to avoid damage to the cooling system.

•Once the appliance is unpacked, make sure that it is complete, that the body

and the electrical cord aren’t damaged. It is forbidden to use a technically

damaged appliance.

CONNECTION TO THE MAINS

–The appliance should only be connected to an earthed socket installed in

accordance with the regulations. Make sure that the supply voltage

corresponds with the voltage marked on the rating label. This product

complies with all binding CE labelling directives. The earthed electrical socket

by which the appliance is connected to the mains should be in an accessible

place. It is a legal requirement that the appliance is properly earthed. The

manufacturer will not be held liable for any damage or injury which may result

from the failure to fulfil this requirement.

–To avoid the exposure to danger, always have faulty cable be replaced only

by the manufacturer, by our customer service or by qualified person and with

a cable of the same type.

–DO NOT USE extension cords or connectors (adapters), or hubs.

–The frequency and power of the electricity supply must conform to the

general data parameters of the appliance as it is shown in the product label.

–When positioning the appliance, be careful that the electrical cord isn’t

squeezed in order to avoid its damage. Do not store heavy objects such as

cooling devices, furniture or other devices next the appliance in such a way

that they could squeeze and damage the electrical cord. This can cause a

short circuit and a fire.

–Make sure that the plug of the electrical cord is not squeezed by the back

wall of the appliance or otherwise damaged. A damaged plug can be the

cause of a fire!

•If the appliance is unplugged (for cleaning, moving to another place, etc.), IT

MAY BE REPEATEDLY SWITCHED ON AFTER 15 MIN.

•The appliance should be used only for storing foodstuffs.

•This appliance is not designed for the storage of explosive substances such as

aerosol cans with a flammable propellant.

•It is prohibited to store petrol and other flammable liquids near the appliance.

•The appliance can’t be disposed of by burning.

•Do not place any switched on electrical devices (such as microwave ovens,

hair dryers, irons, electric kettles or other electrical devices) on top of the

appliance because this may cause ignition of plastic parts.

•Do not place any dishes with liquids on top of the appliance and do not keep

flowers in vases or other liquid-filled vessels on the appliance.

•Do not climb on or sit on the appliance, do not lean on or hang on the

appliance doors and do not allow children to do this.

IF THE APPLIANCE IS OUT OF ORDER AND IT IS NOT POSSIBLE TO

REPAIR IT BY MEANS OF GIVEN RECOMMENDATIONS, UNPLUG IT,

OPEN THE DOORS AND CALL THE SERVICE EXPERT. ONLY A

SERVICE REPRESENTATIVE CAN REMEDY ALL TECHNICAL OR

CONSTRUCTION FAULTS.

TRANSPORT

THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR ANY DAMAGE OF THE

APPLIANCE THAT RESULTS FROM NON-COMPLIANCE WITH THE INSTRUCTIONS

FOR TRANSPORTATION.

•The appliance should be transported only in the vertical position.

•When being transported, the appliance should be protected from atmospheric

conditions (rain, snow, dampness).

•The appliance should be firmly secured in place while being transported, to avoid

slippage or any shocks in the transport vehicle.

•If the appliance was transported not vertically, it may be connected to the

mains after 4 hours at least. If this is not done, the appliance compressor

may fail.

ENVIRONMENTAL PROTECTION INFORMATION

If the appliance is no longer in use, cut the connecting cable off the used equipment

before its scrapping. Also, remove the appliance lock or render it useless so that the

appliance presents no danger to children while being stored for di- sposal. This

appliance is marked with a symbol of the crossed out waste container in conformance

with the European Directive 2002/96/EC. Such marking informs that the equipment may

not be kept together with other waste coming from the household after the period of its

use. The user is obliged to dispose of the appliance at the waste collection point. The local waste

collection points, shops and communal units form an appropriate system enabling the disposal of

the equipment.

Handling the used electrical and electronic equipment properly contributes to the avoidance of

consequences harmful to the human health and natural environment, resulting from the presence

of hazardous substances and improper storage and processing of such equipment.

GENERAL INFORMATION

The appliance is a vertical display cooler with glass doors and with a fan and is designed

for storage of foodstuffs and for chilling of drinks and for a short-term storage of them.

This appliance is intended for commercial use!

THE APPLIANCE IS ECOLOGICALLY CLEAN, CONTAINING NO MATERIALS HARMFUL TO

THE OZONE LAYER: the refrigerant used is R600a, the foaming agent used for the

appliance insulation is cyclopentane C5H10.

THE MANUFACTURER GUARANTEES RELIABLE OPERATION OF THE REFRIGERATOR

WHEN THE AMBIENT TEMPERATURE IS +16 TO +32 DEGREES CELSIUS AND THE

RELATIVE AIR HUMIDITY NOT GREATER THAN 60 PER CENT.

The appliance climate class is 3.

Product temperature class –S.

Product data sheet

Model

ADN 221

ADN221 C

Total gross volume, L

480

Refrigerator net volume , L

455

External overall dimensions (HxWxD),

cm:

for installation with the shield

for installation without the shield

for service

202,5 x 60 x 68,5

202,5 x 65,5 x 125

202,5 x 60 x 75,5

202,5 x 65,5 x 125

Shelf area, dm2

125

Products temperature ranges, °C (In

accordance with EU standard ISO 23953-

2:2015, p .4.2.2)

From +2 to +14

Rated current, A

1,6

Mass, kg

Rated supply voltage

220 –240V/50 HZ

Rated power input, W

265

Noise level, dB (A)

Door opening area, m²

0,84

General product exposure area, m²:

without the promotional shield

with the promotional shield

0,67

0,61

Quantity of bottles, pcs.: 0,33 l PET

0,5 l PET

0,75 l PET

1,0 l PET

1,5 l PET

0,33 l cans

301

252

150

110

616

Maximum loading, kg

Energy consumption at ambient

temperature +25 °C, kWh / year

At switched on lighting:

With the promotional shield

1241

Without the promotional shield

1139

At switched off lighting

730

Nominal imput of luminaire, W

Rated power of the promotional shield,W

NOTE. The manufacturer reserves the right to make future changes to technical parameters and

specifications.

THE APPLIANCE BASIC PARTS (see page 1. fig. 1)

2 ― Thermostat knob. The temperature is controlled using the thermostat knob by

turning it to one side or the other.

3 ― Blower switch. Opening the door, the blower 1switches off.

4 ― On / off switch for interior light. By pressing the button of the double switch 4

with the arrow „downward“, the luminaire 9may be switched on. By pressing

the other button with the arrow “upwards” the luminaire of the promotional

shield may be switched on.

INSTALLATION AND OPERATING CONDITIONS OF THE

APPLIANCE

Preparing the appliance for operation

It is recommended to prepare the appliance for operation with a helper.

Remove boards of foamed polystyrene from the top and the bottom of the appliance. They are

intended for transportation only. Remove adhesive tapes and open the door.

Take out the plug with the supply cord 10 from the water tray 11 (see page 1, fig. 1) which is

placed under a compressor (this is intended for transportation only.

When the appliance is running, the cord can’t be in the tray. The appliance should

not be connected to the mains until all packing and transport materials aren’t removed.

Suitably dispose the packaging material

Take out two supports 1from a bag

and screw them by screws 2into marked

places at the back of a appliance.

Take out the cover 1 from the bag and

insert the cover into the grid 2placed

under the door.

It is permissible the conversion of the

shelf 2. Maximum conversion of the shelves is obtained by

lowering front holders 1by five step.

In case of moving the appliance to another place, lift its front in

such a way that its supports couldn’t touch the floor.

In case of adjusting supports, mount the appliance slightly

inclined backwards to provide a spontaneous closing of its doors.

It is very important that both front supports would abut on the

floor uniformly.

If the appliance is brought in from the cold (temperature is not higher than +12 °C), you

should wait for two hours before connecting it to the mains.

Blower

Adjustable height shelves

Thermostat knob

Thaw water channel cleaner

Blower switch

Advertising panel (ADN221 C)

Double switch -(ON/OFF)

Interior light

Thermometer

Supply cord

Thaw water drip tray

Positioning

•Place the appliance in a dry, well ventilated room.

WARNING! The appliance should not be operated in an unheated room or

porch. Place the appliance away from heat sources such as kitchen

stove/oven, radiators, or direct sunlight.

WARNING! The appliance must not touch any pipes for heating, gas or

water supply or any other electrical devices.

•Do not cover the ventilation holes at the top of the appliance –it must be a good air

circulation around the appliance. There should be a gap of at least 10 cm between the top

of the appliance body and any furniture that may be above it. If this requirement is not

followed, the appliance consumes more electrical energy and its compressor may

overheat.

•If the appliance is placed in a corner, a gap of at least 3 cm must be left between the

appliance body and the wall. Overall space required for use of the refrigerator.

Overall dimensions for installation of the refrigerator - see page 1, fig. 2.

•The appliance must stand on a level surface and must not touch the wall. If necessary,

regulate the height of the appliance by adjusting the levelling feet: by turning them

clockwise –the front of the appliance rises, by turning them counter clockwise –it comes

down. If the appliance is tilted slightly backward –the doors will close by themselves.

TEMPERATURE REGULATION

The temperature in the refrigerator compartment is controlled using the thermostat knob 2(see

page 1, fig. 1) by turning it to one side or the other. The temperature indication in digits is shown

beside the thermostat knob.

The temperature is regulated on the scale of five digits.

0= Compressor is switched off WARNING! Electric current is not switched off.

1= highest temperature (lowest cooling)

5= lowest temperature (highest cooling)

If foodstuffs are too cold, set the thermostat knob to 1, 2or 3. If foodstuffs are being chilled not

sufficiently, set the thermostat knob to 4or 5. Please set the desired temperature in the appliance

according to your own requirements.

THE TEMPERATURE IN THE REFRIGERATOR COMPARTMENT MAY VARY DEPENDING ON

AMBIENT TEMPERATURE, THE AMOUNT OF FOODSTUFFS, THE TEMPERATURE OF THE

FOODSTUFFS AND HOW OFTEN THE APPLIANCE DOORS ARE OPENED AND CLOSED.

IF A ROOM IS COOL, THE APPLIANCE COOLS LESS. THE TEMPERATURE IN THE

APPLIANCE MAY THEREFORE RISE. Use the thermostat wheel to set a lower temperature.

DEFROSTING, CLEANING AND CARE

THE REFRIGERATOR COMPARTMENT DEFROSTS AUTOMATICALLY. Drops of ice that form on the

back wall of the refrigerator compartment thaw during the time the compressor is not working and

the thaw water runs down the thaw water runoff channel to the tray on top of the compressor,

where it evaporates.

REGULARLY CLEAN THE APPLIANCE.

Remember that when cleaning the appliance you must disconnect the appliance

from the electrical energy supply socket by pulling the plug out of the electricity

outlet.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Whirlpool Kühlschrank Handbücher

Whirlpool

Whirlpool ED2VHEXSB00 Bedienungsanleitung

Whirlpool

Whirlpool ET18NKXDG01 Bedienungsanleitung

Whirlpool

Whirlpool 2300257 Bedienungsanleitung

Whirlpool

Whirlpool CS20TKXNQ00 Bedienungsanleitung

Whirlpool

Whirlpool Refrigerator-freezer Bedienungsanleitung

Whirlpool

Whirlpool ED25SMIII Bedienungsanleitung

Whirlpool

Whirlpool EWT8002Q Bedienungsanleitung

Whirlpool

Whirlpool BSNF 8762 OX Installationsanleitung

Whirlpool

Whirlpool GI6FDRXXB Montageanleitung

Whirlpool

Whirlpool WRT111SFA Gebrauchsanweisung

Whirlpool

Whirlpool EDISSC Bedienungsanleitung

Whirlpool

Whirlpool WHR43S1E Bedienungsanleitung

Whirlpool

Whirlpool ER2MHKXPL03 Bedienungsanleitung

Whirlpool

Whirlpool ED5PVEXWS Montageanleitung

Whirlpool

Whirlpool ET6WSKXSQ00 Bedienungsanleitung

Whirlpool

Whirlpool GX5FHDXV Stücklistenhandbuch

Whirlpool

Whirlpool ET4WSKXS Stücklistenhandbuch

Whirlpool

Whirlpool SW8AM2QX2 Bedienungsanleitung

Whirlpool

Whirlpool ET22DKXSW00 Bedienungsanleitung

Whirlpool

Whirlpool WRS950SIAM01 Bedienungsanleitung

Whirlpool

Whirlpool GB9SHDXPB12 Bedienungsanleitung

Whirlpool

Whirlpool ED19HK Bedienungsanleitung

Whirlpool

Whirlpool W8TXEGFYQ Montageanleitung

Whirlpool

Whirlpool 2262431 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung