Whirlpool WHELJ1 Bedienungsanleitung

ow to install, operate

and maintain your Central

Water Filtration System

Model W ELJ1

Whirlpool Central

Water Filtration System

System tested and certified by the Water Quality

Association against CSA B483.1.

7339997 (Rev. D 7/22/14)

Manufactured and warranted by

Ecodyne Water Systems

1890 Woodlane Drive

Woodbury, MN 55125

If you have any questions or concerns when

installing, operating or maintaining your Central

Water Filtration System, call our toll free number:

1-866-986-3223

Monday - Friday, 8 AM - 7 PM EST or visit

www.whirlpoolwatersofteners.com

When you call, please be prepared to provide

the model and serial number of your product,

located on the rating decal on back of the cover.

Installation and Operation Manual

Do not return unit to store

System tested and certified by NSF International

against NSF/ANSI Standard 42

for the reduction of chlorine taste and odor,

and certified to NSF/ANSI Standard 372.

TABLE OF CONTENTS

Page

Specifications & Performance Claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Central Water Filtration System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Inspect Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ow a Central Water Filtration System Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11

Programming the Central Water Filtration System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Start Up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Customizing Features / Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15

Care of Your Central Water Filtration System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19

Exploded View & Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-23

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

FIG. 1

27-1/2”

33-3/4”

3-3/8” 13-7/16”

10-1/8”

IN – OUT

OUT

TOP VIEW

SIDE VIEW FRONT VIEW

Dimensions

SPECIFICATIONS

odel WHELJ1

Rated Service Flow Rate 6.0 gpm (22.7 L/min.)

Pressure Drop at Rated Service Flow 10 psig*(68.9 kPa)

Pressure Drop at 9.6 gpm 15 psig*(103.4 kPa)

Water Pressure Limits (minimum / maximum) 30 - 125 psi

(206.8 - 861.8 kPa)

Water Temperature Limits (minimum / maximum) 40 - 100 °F (5 - 38 °C)

Drain Flow Rate 3.4 gpm

0.50 ppm

0.75 ppm

Rated Capacity at Chlorine Concentration** of: 1.0 ppm

1.5 ppm

2.0 ppm

2,280,000 gal.*

1,520,000 gal.*

1,140,000 gal.*

760,000 gal.*

570,000 gal.*

Sediment Removal with 30-40 micron particle size 95% or more

Sediment Removal with 40-50 micron particle size 99% or more

*From independent laboratory test data.

** Typical residential chlorine concentration is 0.5 to 1.0 ppm.

This system conforms to NSF/ANSI Standard 42 for the specific performance claims

as verified and substantiated by test data.

Specifications & Performance Claims

Questions? Call Toll Free 1-866-986-3223 Monday- Friday, 8 AM - 7 PM EST

or visit www.whirlpoolwatersofteners.com

When you call, please be prepared to provide the model and serial number,

located on the rating decal on back of the cover.

This system has been tested according to NSF/ANSI 42 for the reduction of chlorine taste and odor. The concentra-

tion of the indicated substance in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI 42.

While testing was performed under standard laboratory conditions, actual performance of the system may vary

based on local water conditions.

PERFOR ANCE CLAI S

Substance Influent

Challenge Level

Reduction

Requirement

Average Percent

Removal

Chlorine 2.0 ±10% mg/L 50% 82.8%

Before You Start

=Do not turn the Central Water Filtration System upside down, drop, or set on sharp protrusions.

=The Central Water Filtration System has a maximum allowable inlet water pressure of 125 psi and a minimum of

30 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reduc-

ing valve if necessary (Adding a pressure reducing valve may reduce the flow.). If your home is equipped with a

back flow preventer, an expansion tank must be installed in accordance with local codes and laws.

=The Central Water Filtration System works on 28V DC electrical power, supplied by a direct plug-in power supply

(included). Be sure to use the included power supply and plug it into a nominal 120V, 60 z household outlet

that is in a dry location only, grounded and properly protected by an overcurrent device such as a circuit breaker

or fuse.

=Do not use the Central Water Filtration System with water that is microbiologically unsafe or of unknown quality

without adequate disinfection before or after the system.

European Directive 2002/96/EC requires all electrical and electronic equipment to be disposed of accord-

ing to Waste Electrical and Electronic Equipment (WEEE) requirements. This directive or similar laws

are in place nationally and can vary from region to region. Please refer to your state and local laws for

proper disposal of this equipment.

Central Water Filtration System Safety

Your safety and the safety of others are very important.

We have provided many safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING”

These words mean:

You can be killed or seriously injured if you don’t

immediately follow instructions.

You can be killed or seriously injured if you don’t

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell

you what can happen if the instructions are not followed.

In the state of Massachusetts: The Commonwealth of Massachusetts plumbing code 248-CMR shall

be adhered to. A licensed plumber shall be used for this installation.

Do not return the Central Water Filtration System to store.

If you have any questions, or there are missing parts or damage, please call Toll Free 1-866-986-3223,

Monday - Friday, 8 am - 7 pm EST, or visit www.whirlpoolwatersofteners.com

When you call, please be prepared to provide the model and serial number, found on the rating decal on

back of the cover.

How a Central Water Filtration System Wor s

NOR AL OPERATION

During normal operation water enters the Central

Water Filtration System and flows through several fil-

tration processes where tastes, odors and sediment

are reduced.

CLEAN RINSE CYCLE

A Clean Rinse cycle will automatically be initiated

based on how the controller has been programmed.

The Clean Rinse cycle lifts and expands the media

bed to rejuvenate the media and then repacks the bed

for continued use. During the Clean Rinse cycle, dirt,

sediment, etc. are flushed from the Central Water

Filtration System down the drain.

APPLICATIONS FOR A CENTRAL WATER

FILTRATION SYSTE

=Do not use the Central Water Filtration System with

water that is microbiologically unsafe or of unknown

quality without adequate disinfection before or after

the system.

=The Central Water Filtration System may not be an

effective treatment method for water sources with a

hydrogen sulfide problem (rotten egg odor or taste)

If your water has hydrogen sulfide, contact a water

treatment expert or call 1-866-986-3223.

=The Central Water Filtration System will not remove

iron and is not intended to replace iron treatment

equipment.

=Although the Central Water Filtration System has

sediment filter capabilities, additional sediment filtra-

tion may be needed in problem water applications.

Packing List

Inspect Shipment

Ground Clamp

Kit Drain ose

Bypass Valve

Adaptor Elbow

Installation

Adaptors

FIG. 2

ose Clamps

The parts required to assemble and install the Central

Water Filtration System are included with the unit.

Thoroughly check the Central Water Filtration System

for possible shipping damage and parts loss. Also

inspect and note any damage to the shipping carton.

Remove and discard (or recycle) all packing materials.

To avoid loss of small parts, we suggest you keep the

small parts in the parts bag until you are ready to use

them.

Clips

Grommet

(used for Models W ES33,

W ES44 & W ES48)

LOCATION REQUIRE ENTS

Consider the following when selecting an installation

location for the Central Water Filtration System.

=Do not operate the Central Water Filtration System

where freezing temperatures occur. Do not attempt

to treat water over 100ºF (38ºC). Freezing temper-

atures or hot water damage voids the warranty.

=To condition all water in the home, install the

Central Water Filtration System close to the water

supply inlet, and before all other plumbing connec-

tions, except outside water pipes.

=For a home with municipal water supply, install the

Central Water Filtration System between the home’s

incoming water supply and the water softener, if one

is being used (See Figure 3A). If the home has well

water, reverse the order of the Central Water Filtra -

tion System and the water softener (See Figure 3B).

=A nearby drain is needed to carry away Clean

Rinse discharge water. Use a floor drain, laundry

Installation Requirements

tub, sump, standpipe, or other options (check your

local codes). See "Air Gap Requirements" and

"Valve Drain Requirements" sections. If a drain is

not available, it is still possible to operate the

Central Water Filtration System in a manual Clean

Rinse mode. See “Operating in Manual Clean

Rinse Mode.” The automatic Clean Rinse must be

disabled if the Central Water Filtration System will

not be connected to a drain (See Page 7).

=The Central Water Filtration System works on 28V

DC electrical power, supplied by a direct plug-in

power supply (included). Provide a 120V, 60 z

electrical outlet in accordance with NEC and local

codes.

=Do not install the Central Water Filtration System on

a hot water line (See Figures 3A & 3B, below).

=Avoid installing in direct sunlight. Excessive sun

heat may cause distortion or other damage to non-

metallic parts.

THE PROPER ORDER TO INSTALL WATER TREAT ENT EQUIP ENT

Untreated Water to

Outside Faucets

FIG. 3B

ot Water

to ouse

Cold Water

to ouse

Untreated Water to

Outside Faucets

Water

eater

Optional

Sediment

Filter

Pressure

Tank

Well

Pump

ot Water

to ouse

Cold Water

to ouse

Central

Water

Filtration

System

Water

eater

Water

Softener

Optional

Sediment

Filter

City Water Supply

Well Water Supply

Central

Water

Filtration

System

Water

Softener

FIG. 3A

Installation Requirements

PLU BING CODES

All plumbing must be completed in accordance with

national, state and local plumbing codes.

VALVE DRAIN REQUIRE ENTS

Using the flexible drain hose (included), measure and

cut to the length needed. Flexible drain hose is not

allowed in all localities (check your plumbing codes). If

local codes do not allow use of a flexible drain hose, a

rigid valve drain run must be used. Purchase a com-

pression fitting (1/4 NPT x 1/2 in. minimum tube) and

1/2" tubing from your local hardware store. Plumb a

rigid drain as needed (see Figure 4, below).

NOTE: Avoid drain hose runs longer than 30 feet.

Make the valve drain line as short and direct

as possible.

It is recommended that the Central Water Filtration

System be installed near a drain. owever, if a drain

is not available, it is still possible to operate the

Central Water Filtration System in a manual Clean

Rinse mode. See “Operating in Manual Clean Rinse

Mode” section. The automatic Clean Rinse function

must be disabled if the Central Water Filtration System

will not be connected to a drain.

1-1/2”

air gap

Install adaptor

elbow using hose

clamp. Aim noz-

zle down toward

center of drain

Tie or wire

tubing in

place

FIG. 4

LAUNDRY TUB STANDPIPE

1-1/2”

air gap

FLOOR DRAIN

1-1/2”

air gap

To drain point other

than floor drain.

Support tubing in

place as needed.

Drain

Fitting

Clip

Barbs

1/4 NPT Threads

1/2” Outside Dia.

Copper Tube

(not included)

Comp Fitting. 1/4

NPT x 1/2” O.D.

Tube (not included)

Cut barbs from

drain fitting (pull

clip to remove fit-

ting from valve)

CONNECTING VALVE TO DRAIN

SUBSTITUTING RIGID DRAIN LINE

ose

Clamp

Valve

Drain

ose

Drain grate with 1”

dia. hole in center

In the state of Massachusetts: The Commonwealth

of Massachusetts plumbing code 248-CMR shall

be adhered to. A licensed plumber shall be used

for this installation.

AIR GAP REQUIRE ENTS

A drain is needed for Clean Rinse discharge water. A

floor drain, close to the Central Water Filtration

System, is preferred. A laundry tub, standpipe, etc.

are other drain options. Secure valve drain hose in

place. Leave an air gap of 1-1/2” between the end of

the hose and the drain. This gap is needed to prevent

backflow of sewer water into the Central Water

Filtration System . Do not put the end of the drain

hose into the drain.

Installation Requirements

INLET - OUTLET PLU BING OPTIONS

Always install either a single bypass valve (provided)

to the contractor/plumber-supplied plumbing, as shown

in Figure 7 OR if desired, a 3 valve bypass system

(parts not included) can be installed, as shown in

Figure 6. Bypass valves allow you to turn off water to

the Central Water Filtration System for maintenance if

needed, but still have water in house pipes.

Use either:

=Copper pipe

=Threaded pipe

=PEX (Crosslinked Polyethylene) pipe

=CPVC plastic pipe

=Other pipe approved for use with potable water

I PORTANT: Do not solder with plumbing attached to

installation adapters and single valve

bypass. Soldering heat will damage the

adapters and valve.

FIG. 7

FIG. 6

3 VALVE BYPASS

Central Water Filtration

System INLET

INOUT

Clip (2)

Valve

Inlet

1” NPT

Adapter (2)

1” NPT Sweat

Adapter (2)

(not included)

CROSS OVER

FIG. 5

To Central Water

Filtration System

ain Water Pipe

In what direction does the water flow?

Be sure to plan piping so water flow is to the

Central Water Filtration System valve INLET.

Plan a crossover if flow is from left to right.

Treated

Water from

Valve

OUTLET

Central Water Filtration

System OUTLET

Untreated

Water to

Valve

INLET

CONNECTING PLU BING TO VALVE

Included

1” NPT

Adapter (2)

Clip (4)

1” NPT Sweat

Adapter (2)

(not included)

Bypass

Valve

Inlet

INOUT

Included

Use Teflon® tape,

pipe joint com-

pound or both

Use Teflon® tape,

pipe joint com-

pound or both

Installation Instructions

TURN OFF WATER SUPPLY

1. Close the main water supply valve, near the well

pump or water meter.

2. Open all faucets to drain water from the house

pipes.

NOTE: Be sure not to drain water from the water

heater, as damage to the water heater ele-

ments could result.

OVE THE CENTRAL WATER FILTRATION

SYSTE INTO PLACE

Post

Top Cover

RE OVE TOP COVER AND HANG IT

FRO POST ON FRONT OF RI

FIG. 9

Plywood

Shim(s)

LEVEL IF NECESSARY

FIG. 8

1. Move the Central Water Filtration System into instal-

lation position. Set it on a level surface. If needed,

place the unit on a section of plywood, a minimum

of 5/8” thick. Then place shims under the plywood

to level the Central Water Filtration System (see

Figure 8).

2. Remove top cover.

3. ang cover from post on front of rim, as shown in

Figure 9. Avoid allowing cover to hang from wires.

Excessive Weight Hazard

Use two or more people to move and install

Central Water Filtration System.

Failure to do so can result in back or other

injury.

1. Install metal grounding clamp to metal house water

supply pipes before beginning installation.

2. Securely tighten connection in center of metal

ground clamp (See Figure 10).

3. Loosely assemble any pipe and fittings needed from

the main water supply to the inlet and outlet ports of

the Central Water Filtration System valve.

I PORTANT:

=Be sure to fit, align and support all plumbing to pre-

vent putting stress on the Central Water Filtration

System valve inlet and outlet. Undue stress from

misaligned or unsupported plumbing may cause

damage to the valve.

=Be sure to keep fittings fully together, and pipes

squared and straight.

=Be sure incoming water supply pipe goes to the

Central Water Filtration System valve INLET side.

Inlet and outlet are marked on the valve. Trace the

water flow direction to be sure.

4. Complete the inlet and outlet plumbing for the type

of pipe as described at right:

Installation Instructions

FIG. 10

Ground

Clamp (2)

Screw with

locking nut

Plastic

Bypass

Valve

Metal

Pipes

Soldered Copper

1. Thoroughly clean and apply solder flux to all joints.

2. Make all solder connections.

I PORTANT: Do not solder with plumbing attached to

installation Adapters and single valve

bypass. Soldering heat will damage the

Adapters and valve.

Threaded Pipe

1. Apply pipe joint compound or Teflon® tape to all

male pipe threads.

2. Tighten all threaded joints and make all solder con-

nections.

CPVC Plastic Pipe

1. Clean, prime and cement all joints, following the

manufacturer's instructions supplied with the plastic

pipe and fittings.

Other, including PEX (Crosslinked

Polyethylene)

1. Follow the piping system manufacturer's instructions

when using other pipe approved for potable water.

® Teflon is a registered trademark of E.I. Du Pont de

Nemours and Company.

Electrical Shock Hazard

Install metal ground clamp to metal house

water supply pipe before beginning installation.

Securely tighten connection in center of metal

ground clamp.

Failure to do so can result in death or

electrical shock.

ASSE BLE INLET AND OUTLET PLU BING

A ground clamp should be installed on the household

plumbing supply lines in accordance with the National

Electric Code.

Andere Handbücher für WHELJ1

Inhaltsverzeichnis

Andere Whirlpool Wasserfiltersystem Handbücher

Whirlpool

Whirlpool WHEUFF Bedienungsanleitung

Whirlpool

Whirlpool WHES60 Bedienungsanleitung

Whirlpool

Whirlpool TITANIUM P-06CRS Bedienungsanleitung

Whirlpool

Whirlpool EveryDrop S3RFWG60NP Stücklistenhandbuch

Whirlpool

Whirlpool WHER25 Bedienungsanleitung

Whirlpool

Whirlpool WHEMB40 Bedienungsanleitung

Whirlpool

Whirlpool WHED10 Bedienungsanleitung

Whirlpool

Whirlpool minerala 65 Bedienungsanleitung

Whirlpool

Whirlpool WHELJ1 Bedienungsanleitung

Whirlpool

Whirlpool WHELJ1 Bedienungsanleitung

Whirlpool

Whirlpool WHELJ1 Bedienungsanleitung

Whirlpool

Whirlpool WHAROS5 Bedienungsanleitung

Whirlpool

Whirlpool WHEMB40 Bedienungsanleitung

Whirlpool

Whirlpool WHEMB40 Bedienungsanleitung

Whirlpool

Whirlpool WHAPSRO Bedienungsanleitung

Whirlpool

Whirlpool WHCF-DWH Bedienungsanleitung

Whirlpool

Whirlpool 7WUC4801S0 Bedienungsanleitung

Whirlpool

Whirlpool UltraEase WHAWH90 Bedienungsanleitung

Whirlpool

Whirlpool WHELJ1 Bedienungsanleitung

Whirlpool

Whirlpool WHCF-DUF Bedienungsanleitung

Whirlpool

Whirlpool WHED10 Bedienungsanleitung

Whirlpool

Whirlpool WHKF-IMTO Bedienungsanleitung

Whirlpool

Whirlpool WHKF-DWH Bedienungsanleitung

Whirlpool

Whirlpool WHKF-DWHV Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung