Whistler WBU-800EU Bedienungsanleitung
WIRELESS DIGITAL
BACKUP CAMERA
INSTALLS IN MINUTES
WBU-800EU
User Guide
2
Because the WBU-800EU is truly wireless and does not tap into
your vehicle's transmission or backup light, you must tell the unit
when you are backing up. This also allows you to use your back up
camera to view behind the vehicle at any time.
When power is applied to the monitor an image will be present for
60 sec by default or the user selected time, if the screen goes blank
and more time is required press the for an image to return to
the monitor.
Welcome
Thank you for choosing a Whistler product. We are dedicated to
providing products that represent both quality and value. Please
read the User Guide carefully before using this product. If you have
additional questions visit our website at
www.whistlergroup.com
or call Tel (479) 273-6012,
8am to 5pm CT, Monday through Friday
to speak to a Customer Service Representative.
INTRODUCTION
3
TABLE OF CONTENTS
Components ......................................................................................................... 4
Getting Started................................................................................................. 5-6
Test the Camera / Pairing.............................................................................. 7-8
Assembly / Installation...................................................................................... 9
Attach to Vehicle................................................................................................10
Mounting the Monitor.....................................................................................11
Setup......................................................................................................................12
Monitor Settings......................................................................................... 13-15
Troubleshooting ................................................................................................16
Disclaimer ............................................................................................................17
Safety .....................................................................................................................18
Care and Maintenance ....................................................................................19
CE, FCC, and IC Information.................................................................... 20-21
Specications......................................................................................................22
Warranty Information ............................................................................... 23-27
4
COMPONENTS
1. Monitor
2. Camera with solar cells
3. Suction cup mount
4. Dash disk
5. USB Charge cord
6. Monitor power cord
7. Pairing tool
1
2
3 4
5
6
7
5
GETTING STARTED
The WBU-800EU is equipped with a built-in rechargeable lithium
battery and is connected with two solar panels that trickle charge
the built-in lithium battery when sunlight is available. This will
minimize or eliminate the need to manually charge the unit during
the year.
A USB charging port is provided to initially charge the battery
prior to mounting on your vehicle as well as to recharge if needed.
Your rechargeable battery when fully charged will last for several
months of average use with NO SUNLIGHT (average use is defined
as 4~6 times per day). With the addition of sunlight, the solar cells
will charge your battery thereby extending the cameras ability
to provide usage day after day and month after month without
requiring you to recharge it manually.
Remove camera assembly from box and make sure all components
are included.
6
CHARGE THE CAMERA
1. Connect the supplied USB cord to the micro USB port of the
camera assembly.
2. Plug the USB cable into any standard USB charger with an
output rating of 500ma or higher.
3. Charge the camera for 5 to 6 hours.
4. Close USB door securely to ensure waterproof integrity.
GETTING STARTED
Under normal use, the camera maintains a charge with exposure
to sunlight.
NOTE: If vehicle will be stored for periods of time greater than two
months, please turn off camera using the switch on the rear of the
camera to the Off position to prevent the battery from discharging.
USB door closed USB door opened
Micro USB port
7
TEST THE CAMERA / PAIRING
TEST THE CAMERA
Prior to attaching the license plate to your vehicle, follow the steps
below to ensure pairing between the backup camera and monitor.
1. Slide the switch on the rear housing of the camera to the On
position.
2. With power applied to the monitor, the top right button will
illuminate to indicate the monitor is ON.
3. The top right button will blink briefly to indicate that it is
attempting to communicate with the camera. When connected
to the camera, the top right button will turn solid. It may take a
moment for the camera to begin sending the video information.
Allow time for the image to be displayed.
4. If no image appears, see Troubleshooting section of this user
guide. The image will time out in 60 seconds (unless user has
selected a different time out option) however, if you wish to shut
the image off manually, press anytime that video is present
to stop the video transmission and put the camera back into the
power conserve mode. (The top right button will shut off when
the timer expires)
5. The camera is equipped with 4 IR LEDs and a light sensor to
automatically illuminate during low light conditions. These IR
LED's are invisible to the human eye.
NOTE: If using a switched 12-volt DC Power port, it is not necessary
to power off the monitor.
8
TEST THE CAMERA / PAIRING
Switch
PAIRING MONITOR TO CAMERA
Your WBU-800EU should automatically pair with your monitor. If
your monitor does not automatically pair with the camera after
initial charge, the following steps are to be used.
NOTE: There are two ways to pair the camera, select the one that
works best for your situation.
1. Turn off the camera using the switch on the back of the camera.
If already mounted to vehicle skip step 1.
2. Power on monitor.
3. Press then or to place cursor over SETUP, then press
power to select.
4. With PAIR icon selected, press power to select process.
5. This system can support 2 cameras, select the camera you
would like to pair. Camera 1 is the rear camera, Camera 2 is the
front camera.
6. Using switch on back of camera, turn camera back on.
If your camera is mounted to your vehicle, use the pairing tool to
press and release the pair button located above the Micro USB
charge port.
Pair OK will be displayed when the pairing process is completed.
2
PAIR
1
ON
PAIR
Pair button
9
Unit is assembled at the factory for mounting along top edge
of License plate. See Disclaimer section of this user guide
before mounting to vehicle.
NOTE: If you will be attaching the unit to the bottom of your
license plate, please follow the steps below:
1. Locate then remove the four screws holding the bracket onto
the camera.
2. Flip bracket, use the four screws to attach to back of camera.
The end result should be the USB door on the right hand side
as you face the camera when mounted to the bottom of your
license plate.
NOTE: Be sure when securing the camera assembly to not impair
readibility of the state, registration decal, stamp, or other device
indicating the month and year in which the vehicles registration
expires when securing to your license plate.
2
ASSEMBLY / INSTALLATION
1
10
ATTACH TO VEHICLE
ATTACH LICENSE PLATE TO VEHICLE
Once you have tested the camera system and ensured the pairing
between the backup camera and monitor, you are ready to
reattach the license plate to your vehicle.
Use your OEM license plate mounting hardware when mounting
license plate to vehicle.
ADJUST VIEWING ANGLE
The camera angle should be adjusted to provide an optimal view
of objects behind the vehicle.
NOTE: Do not exceed 45 degrees down from central position.
• Loosen the two screws below the camera a few turns.
(Do not remove.)
• To adjust the camera angle, tilt the camera to the correct
angle. (Do not force the camera)
• The camera should be adjusted to a horizontal position
relative to the ground, so as to provide optimal view of
objects behind the vehicle
• Carefully tighten the 2 screws to prevent the camera angle
from moving during vibrations from driving
Screws
Inhaltsverzeichnis
Andere Whistler Digitalkamera Handbücher
