White Rodgers 36C03 Series Bedienungsanleitung

Pilot Gas Outlet:

Located at outlet end of the valve

Type of Gas

Suitable for all domestic heating gases

Pressure Rating: 1/2 lb. per sq. in.

Pressure Regulator Adjust Range (Typical, See

Control Label):

Natural Gas: 2.5 to 5.0" W.C.

LP Gas: 7.5 to 12" W.C.

Ambient Temperature: -40° to 175°F

Thermocouple:

(24V & 120V types): Use W-R Type HO6

(.750V Quick Drop Out Power Unit for

36D34 models only): Use W-R Type H19E

Pilot Generator (.750 volt types):

Use W-R Type G01A-32

Mounting: Any position except upside-down

PIPE SIZES/CAPACITIES

Pipe Size

(inches)

Capacity (BTU/hr) at

1” pressure drop across valve

⁄

” x

⁄

”

⁄

” x

⁄

”

⁄

” x

⁄

”

⁄

” x

⁄

”

100,000

230,000

280,000

162,000

372,600

453,600

Nat. Gas

(1000 BTU/cu. ft.,

64 Sp. Gr.)

LP Gas

(2500 BTU/cu. ft.,

1.53 Sp. Gr.)

INLET BOSS

UP OR DOWN

UPRIGHT

LEFT OR RIGHT

Upright, 90°from upright or vertical

NOTE: Control shown may not be identical

to replacement control.

OFF

INSTALLATION INSTRUCTIONS

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE

INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY

AND/OR PROPERTY DAMAGE.

The 36C03, 36C13 and 36D34 complete gas controls

combine into a single compact package the functions of

3-position gas cock, pressure regulator, 100% shut-off

automatic pilot, and main operator. Separate models

are available for use on 24 VAC, 120 VAC and .750 VDC

systems.These controls can be mounted in any orientation

except upside down.

MODELS AVAILABLE

Model No. Voltage

36C03

36C03A

36C03U

36C13

36C13A

36C13U

36D34U

Current

.23 Amp

.035 Amp

.23 Amp

.035 Amp

24 volts

120 volts

.750 volts

24 volts

120 volts

.750 volts

Gas

Nat.

Nat./LP

OFF

PILOT

ECO

Terminals

OFF

PILOT

The 36C03 and 36C13 models are also available without

pressure regulator as a Model 36C10.

The 36D34 model is limited to .750 VDC applications and

is equipped with a "quick drop out" power unit for vented

gas hearth products.

Operator: Save these instructions for future use!

DESCRIPTION

SPECIFICATIONS

36C03, 36C10, 36C13 and 36D34

Combination Gas Valves

(24 Volt, 120 Volt and .750 Volt Models)

PART NO. 37-5781E

Replaces 37-5781D

1547white-rodgers.com

1. Do not short out terminals on gas valve or

primary control to test. Short or incorrect

wiring cancause equipmentdamage,property

damage, and/or personal injury.

2. This control is not intended for use in locations

where it may come in direct contact with

water. Suitable protection must be provided

to shield the control from exposure to water

(dripping, spraying, rain, etc.).

MAIN PIPING CONNECTIONS

All piping must comply with local codes, ordinances,

and/or national fuel gas codes.

1. Turn off electrical power to the system at the fuse box

or circuit breaker. Also turn off the main gas supply.

2. If replacing an existing valve, disconnect all plumbing

and electrical connections from the old control.

3. The control may be installed in any orientation except

upside down. The arrow on the valve indicates the

direction of gas ﬂow through the control.

4. You should use new pipe that is properly chamfered,

reamed, and free of burrs and chips. If you are using

old pipe, be sure it is clean and free of rust, scale,

burrs, chips, and old pipe joint compound.

SPECIFICATIONS

INSTALLATION

5. Apply pipe joint compound (pipe dope) or teﬂon tape

that is approved for all gases, only to the male

threads of the pipe joints.DO NOT apply compound

or teﬂon tape to the ﬁrst two threads (see ﬁg. 1 for

typical piping connections).

6. If you are using a vise or open-end wrench to hold the

valve while installing piping, do not tighten excessively,

as this may damage the valve.

7. If additional clearance for the gas cock knob is required

when installing the new valve in an existing system,

rotate the knob to the position between ON and OFF.

Depress the knob while turning the valve. The knob

will depress only while in this position.

8. See SYSTEM WIRING when making electrical

connections. After all gas and electrical connections

are completed, turn gas on and check for gas leaks

with leak detection solution or soap suds. Bubbles

forming indicate a leak. SHUT OFF GAS AND FIX

ALL LEAKS IMMEDIATELY.

DO NOT BEGIN INSTALLATION UNTIL YOU READ

THE FOLLOWING PRECAUTIONS.

1. Failure to turn off electric or main gas supply

to heating system could cause personal

injury and/or property damage by shock, gas

suffocation, ﬁre, and/or explosion.

2. Do not use this control on circuits exceeding

speciﬁed voltage.Higher voltage will damage

the control and may cause shock or ﬁre

hazard.

3. NEVER USE FLAME OR ANY KIND OF SPARK

TO CHECK FOR GAS LEAKS–COULD CAUSE

FIRE AND/OR EXPLOSION.

4. Do not use a control set for natural gas with

LP gas,or a control set for LP gas with natural

gas.Personal injury and/or property damage,

gas suffocation, ﬁre, and/or explosion may

result.

WARNING

If you do not follow these instructions exactly, a fire or explosion may

result, causing property damage, personal injury or loss of life.

CAUTION

NOTE

INSTALLATION (cont’d)

PILOT GAS CONNECTION

Install ﬁtting into pilot gas outlet (see ﬁg. 2), turning until

ﬁnger-tight. Insert clean, deburred tubing all the way

through the ﬁtting. While holding the tubing securely,

slowly tighten ﬁtting until you feel a slight "give". Tighten

the ﬁtting an additional 1 1/2 turns.

SYSTEM WIRING

To prevent electrical shock and/or equipment

damage, disconnect electrical power to system at

main fuse or circuit breaker box until installation

is complete.

All wiring should be installed in accordance with local

and national electrical codes and ordinances.

Always check that the electrical power supply used agrees

with the voltage and frequency shown on the gas control.

The typical wiring diagram shows only the terminal

identiﬁcation and wiring hook up. Always refer to wiring

instructions provided by Equipment Manufacturer for

system hookup operation.

CAUTION

NOTE

Line voltage

operating

control

Line

Gas valve

High

limit

Figure 6. Wiring for 36C03A/36C13A (120 Volt)

Pilot gas

outlet

Gas outlet

PILOT

PRESS

TAP

Figure 2. Gas valve side view

High

Limit

TH TH-PG PG

Thermostat

White-Rodgers

36C Gas Valve

Power

Unit To Pilot

Generator

Figure 3. Wiring for 36C03U/36C13U/36D34U (.750 Volt)

Gas valve

terminal panel

Figure 4. Wiring for 36C03/36C13 (24 Volt)

TH TH-TR TR

Line

24 VAC

Hot

Transformer

Thermostat

High

limit

Thermocouple

Connection

E.C.O. Device

on Appliance

Lead

Assembly

E.C.O.

Terminals

Figure 5. Wiring for Energy Cut-Off (E.C.O.) connection

NOTE

If appliance does not have

any E.C.O. device, jumper

E.C.O. terminals.

Horizontal

Drop

Piped Gas

Supply

Gas Valve

3 in.

minimum

Gas Valve

Riser

Piped Gas

Supply

3 in.

minimum

Drop

Horizontal

Riser Gas Valve

Tubing Gas

Supply

3 in.

minimum

NOTE:

Always Include

A Drip Leg In Piping

Figure 1. Typical gas valve piping

INSTALLATION (cont’d)

ENERGY CUT OFF (E.C.O.)

CONNECTION

A ﬁve-function valve uses the two E.C.O. terminals that

are connected to the magnetic assembly where the

thermocouple connects to the 36C valve line interrupter.

Connect the leads from the E.C.O.terminals to the E.C.O.

device on the furnace.Test the E.C.O.device for continuity.

If there is no continuity, the power unit will not hold in.

See ﬁgure 5.

If the furnace does not have an E.C.O. device, jumper

the E.C.O. terminals on the valve with the jumper loead

provided.

THERMOCOUPLE CONNECTION

(For .750 VDC (Special), 24 VAC and

120 VAC Models)

The thermocouple connection should be clean to ensure

good electrical contact.

Run the thermocouple nut into the power unit tapping as

far as possible by hand.Then use a small wrench to set the

nut with a 1/4 to 1/2 additional turn. Do not overtighten.

PILOT GENERATOR CONNECTION

(For .750 VDC Models)

Be sure the pilot generator is completely engaged into

the pilot burner.

Be sure that the two terminals from the pilot generator are

securely tightened beneath the proper screws on the valve.

Connect the power unit lead to the high limit and the high

limit to the TH-PG terminal.

PILOT GAS ADJUSTMENT

If the pilot ﬂame is low and does not engulf the bulb of

the mercury ﬂame sensor, the system will not energize

the main valve. If pilot gas pressure is too high, gas will

sputter past the ignition electrode, and may not ignite.High

pilot gas pressure may also cause the ﬂame to lift off the

burner, causing the ﬂame sensor bulb to sense "low" heat.

To adjust the pilot gas pressure, remove the cover screw

(see ﬁg. 7). To REDUCE pilot pressure, turn the pilot

adjust screw (beneath the cover screw) clockwise. To

INCREASE pilot pressure, turn the pilot adjust screw

counterclockwise. Replace and tighten cover screw.

PRESSURE REGULATOR

ADJUSTMENT

The pressure regulator has been factory adjusted

(see control for speciﬁc setting). Although additional

adjustments will not normally be necessary, you may

adjust the regulator. Do not force the adjusting screw

beyond the limits that it can easily be adjusted.

1. Energize valve to ignite main burner.

2. Remove "Reg. Adj." cover screw (see ﬁg. 8).

3. To DECREASE outlet pressure, turn the adjusting

screw (beneath the cover screw) counterclockwise.

To INCREASE outlet pressure, turn the adjusting

screw clockwise.

4. Replace the cover screw. Cycle the valve two or three

times to verify regulator setting.

Pilot adjust

cover screw

Figure 8. Pressure regulator adjustment

Regulator adjusting

cover screw

OFF

PILOT

Pilot adjust

cover screw

Gasket

Pilot

adjust

screw

Figure 7. Pilot gas adjustment

LIGHTING INSTRUCTIONS

PILOT LIGHTING INSTRUCTIONS

AND PRECAUTIONS

A. This appliance has a pilot that must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING, smell all around the appliance area

for gas. Be sure to smell next to the ﬂoor because some

gas is heavier than air and will settle on the ﬂoor.

FOR YOUR SAFETY

"WHAT TO DO IF YOU SMELL GAS"

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call you gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by

hand, don't try to repair it;call a qualiﬁed service technician.

Force or attempted repair may result in a ﬁre of explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualiﬁed service technician to inspect

the appliance and to replace any part of the control system

and any gas control that has been under water.

1. STOP! Read the precautionary information above.

2. Set the thermostat to lowest setting.

3. Turn off all electrical power to the appliance.

4. Depress gas control knob slightly and turn clockwise to

OFF (see ﬁg. 9). If knob is in ON, turn clockwise to PILOT,

then depress knob slightly and turn clockwise to OFF.

NOTE: Knob cannot be turned from PILOT to OFF unless

knob is depressed slightly. Do not use tools or excessive

force.

5. Wait ﬁfteen (15) minutes to clear out any gas. If you then

smell gas, STOP! Follow Bin the precautionary information

above. If you don't smell gas, go to next step.

6. Remove the pilot access panel(s) located under the gas

control unit.

7. Find pilot - follow small metal tubes from gas

control.

8. Turn knob on gas control counterclockwise to PILOT.

9. Depress control knob all the way and hold in. Immediately

light the pilot with a match. Continue to hold the control

knob down for about one (1) minute after the pilot is lit.

Release knob and it will pop back up. Pilot should remain

lit. If it goes out, repeat steps 4, 5, 8, and 9.

• If knob does not pop up when released, turn clockwise to

OFF, stop and immediately call your service technician

or gas supplier.

• If the pilot will not stay lit after several tries, turn the gas

control knob to OFF and call your service technician or

gas supplier.

10. Replace pilot access panel(s).

11. Turn gas control knob counterclockwise to ON.

12. Turn on all electrical power to the appliance.

13. Set thermostat to desired setting.

1. Set the thermostat to lowest setting.

2. Turn off all electrical power to the appliance if service is

to be performed.

3. Turn gas control knob clockwise to PILOT.

4. Depress gas control knob slightly and turn clockwise to

OFF. Do not use tools or excessive force.

OFF

PILOT

Gas Control

Knob

36C Series

Indicator Gas cock

knob

Figure 9. Gas Cock Knob

OFF

PILOT

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING

If you do not follow these instructions exactly, a fire or explosion may

result, causing property damage, personal injury or loss of life.

PILOT

BURNER

THERMO-

COUPLE

TO TURN OFF GAS TO APPLIANCE

NOTES

White-Rodgers is a business

of Emerson Electric Co.

The Emerson logo is a

trademark and service mark

of Emerson Electric Co.

white-rodgers.com

emersonclimate.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere White Rodgers Steuereinheit Handbücher

White Rodgers

White Rodgers 36E52-214 Bedienungsanleitung

White Rodgers

White Rodgers 758-1 Bedienungsanleitung

White Rodgers

White Rodgers 5C06 Bedienungsanleitung

White Rodgers

White Rodgers 36C03 Bedienungsanleitung

White Rodgers

White Rodgers 8J48A Bedienungsanleitung

White Rodgers

White Rodgers 36E22-214 Bedienungsanleitung

White Rodgers

White Rodgers 47D43-811 Bedienungsanleitung

White Rodgers

White Rodgers 5A75 Bedienungsanleitung

White Rodgers

White Rodgers 1127 Bedienungsanleitung

White Rodgers

White Rodgers 36J27-554 Bedienungsanleitung

White Rodgers

White Rodgers 50A55-285 Bedienungsanleitung

White Rodgers

White Rodgers 50T35-743 Bedienungsanleitung

White Rodgers

White Rodgers 764-700 Bedienungsanleitung

White Rodgers

White Rodgers 50T35-743 Bedienungsanleitung

White Rodgers

White Rodgers 36E93-304 Bedienungsanleitung

White Rodgers

White Rodgers 1311 Bedienungsanleitung

White Rodgers

White Rodgers 50M56U-843 Bedienungsanleitung

White Rodgers

White Rodgers 50M56X-843 Bedienungsanleitung

White Rodgers

White Rodgers 11B18 Bedienungsanleitung

White Rodgers

White Rodgers 50V64-743 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung