Wideye ISAVI ISATHUB Bedienungsanleitung

PLEASE READ THIS GUIDE CAREFULLY BEFORE ATTEMPTING TO OPERATE THE

ISATHUB.

ISAVI ISATHUB QUICK START GUIDE

Your Satellite Telephone Number is: (supplied at time of delivery)

Your Wi-Fi Password is: TBD (all letters upper case)

The Wi-Fi SSID is TBD

Setup

1. If you are using a smartphone or tablet, install the two free

Isathub Apps from the Appstore or your Android store (IsatHub

Control & IsatHub Voice).

If using a PC, you will use a bowser to connect to the Isathub user

interface. More about this later.

2. Power up the iSavi by depressing the On/Off Button firmly until the

pointing LEDs turn green.

3. Set the terminal outside facing upward to allow the unit to acquire

a GPS position fix. You will see three green point lights flashing

sequentially while the GPS fix is being acquired. This may take up

to five minutes in a new location.

4. Point the iSavi as described by the flashing green Pointing LEDs.

(tip up and down and pan left or right). Once all four Pointing LEDs

are solid green press the Pointing Button. The ISavi is now

connected to the Isathub network (but not yet connected to the

internet, and not using you data allotment).

5. At this point any smart device connected to the iSavi Wi-Fi can

make voice calls using the Isathub Voice app.

Connecting to the Internet w/ Smart Device

1. Connect your device to the iSavi Wi-Fi hotspot using the standard

Wi-Fi connection process. The Wi-Fi password can be found on the

back of the iSavi terminal and at the top of this instruction sheet.

2. Once connected to the iSavi Wi-Fi, use the control app to register

and/or make and break data connections.

3. You will use the following credentials from the Isathub control app

Username: admin

Password:1234

4. Once the terminal is registered, you can you the voice app to make

and receive voice calls.

5. Once the data connection is completed, all connected devices can

use the internet via the satellite connection.

6. Be sure to disconnect data when an internet connection is not

required. Also, if using a PC, be sure to deactivate any automatic

software updates on your PC.

Connecting to the Internet w/ a Wi-Fi PC

1. Connect your PC to the iSavi Wi-Fi hotspot using the standard Wi-

Fi connection process. The Wi-Fi password can be found on the

back of the iSavi terminal and at the top of this instruction sheet.

2. Once connected to the iSavi Wi-Fi, use the Web Page based control

page to register and/or make and break data connections as

follows: Open a browser and enter the following IP address into

the address box: 192.168.1.35. This will take you to the web

console.

3. You will be asked for a Username and Password. Use the following:

(this is not the Wi-Fi Password):

Username: admin

Password:1234

4. After logging in you will be taken to the Home page, where you

can see the signal strength, battery level, registration status and

data connection status:

7. If the device is not yet registered with the network, click “Register

Network”. Wait while the terminal registers.

8. Once registered, the terminal is ready to send and receive text

messages. Use the SMS tab for these operations.

9. After registration is complete, you will see the following data on

the Home page. Once the data connection is completed, all Wi-Fi

connected devices can use the internet via the satellite connection.

10. At any time the data usage can be checked by navigating to

the Data Tab.

11. Be sure to disconnect data when an internet connection is

not required. Also, if using a PC, be sure to deactivate any

automatic software updates on your PC.

Call out using the Voice App on Smart Phone

Dial (00) + (Country Code) + (Phone Number) Example: If you want

to dial 1-510-923-9123 you would dial 00-1-510-923-9123 and press

the “phone” button at the bottom of the dial pad. (please note: The

country code for the United State is ALWAYS “1”).

Call in to the Voice App on Smart Phone

Direct Dialing. This is a International call. From the USA, please dial

(011) + (iSavi phone #). Call charges to the phone are paid by the

originator (call charges vary widely from $2.00 to $7.00 per minute,

please contact long distance carrier for specific rates). The user of

the iSavi terminal phone is not charged for this type of call.

Texting out using the Voice App on Smart Phone

Text to 001 + (area code) + (number). Example: 001 504-

512-5555. Your recipient can reply to your text directly in

the normal manner.

Texting to the Voice App on Smart Phone

You can text to the iSavi terminal for free from the following

Inmarsat website. You will see a SMS widget as shown:

http://connect.inmarsat.com/Services/Land/IsatPhone/SMS/

sms.html

Users can text from an IOS device using iMessage by texting

to “+”( iSavi phone number). Example: +870772105201.

Turn iMessage on and “Send as SMS” off on the IOS device.

Inhaltsverzeichnis

Andere Wideye Modem Handbücher

Wideye

Wideye SABRE I Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung