Wiedamark LSD-18.25 Bedienungsanleitung

LED ViDEo Curtain

User ManUal

Table&of&contents&

1.#INTRODUCTION#..........................................................................................................................................#3#

1.1&Underlying&information&and&preparation...................................................................................................&3&

2.#SAFETY#INSTRUCTIONS#............................................................................................................................#4#

3.#OPERATING#DETERMINATIONS................................................................................................................#5#

4.#COMPONENTS#OF#A#DISPLAY...................................................................................................................#6#

4.1&Mounting&elements&and&connections&of&a&display&....................................................................................&6&

4.2&All>in>one&network&control&system&LED&Show&T9.....................................................................................&7&

4.3&Network&control&system&LED&Studio&......................................................................................................&11&

5.#MOUNTING#................................................................................................................................................#12#

5.1&Safety&instructions.................................................................................................................................&12&

5.2&Allowed&number&of&units&connected&on&one&suspension&point...............................................................&12&

5.3&Mounting&steps......................................................................................................................................&13&

6.#CONNECTIONS#.........................................................................................................................................#15#

6.1&Control&system&LED&Show&T9................................................................................................................&15&

6.2&Control&system&LED&Studio....................................................................................................................&17&

6.3&Connection&to&the&mains&........................................................................................................................&18&

6.4&Installation&and&connection&of&the&PCI&sending&card&for&the&control&system&LED&studio&.......................&

19&

6.5&Connection&and&operation&of&the&external&sending&card&for&the&control&system&LED&Studio&.................&

20&

6.6&Function&test&with&the&interfaces&............................................................................................................&20&

7.#INSTALLATION#AND#CONFIGURATION#OF#THE#CONTROL#SYSTEMS#.............................................#21#

7.1&Control&system&LED&Show&T9................................................................................................................&21&

7.2&Testing&LED&Show&T9&and&playing&a&video&file&......................................................................................&29&

7.3&Control&system&LED&Studio....................................................................................................................&31&

7.4&Testing&LED&Studio&and&playing&a&video&file&..........................................................................................&37&

8.#CLEANING#AND#MAINTENANCE#.............................................................................................................#39#

8.1&Replacing&a&power&adaptor&....................................................................................................................&39&

8.2&Replacing&LEDs&....................................................................................................................................&42&

9.#PROBLEM#CART.......................................................................................................................................#44#

10.#TECHNICAL#SPECIFICATIONS...............................................................................................................#45#

Every person involved with the installation, operation and maintenance of this device has to

-be qualified

-follow the instructions of this manual

-consider this manual to be part of the total product

-keep this manual for the entire service life of the product

-pass this manual on to every further owner or user of the product

-download the latest version of the user manual from the Internet

1. INTRODUCTION

Thank you for having chosen aWiedamark Soft Display. If you follow the instructions given in this

manual, we are sure that you will enjoy this device for along period of time.

Software shown in the manual.

LED Show T9

For this user manual, [LED Show T9] was used with [Version 10.48].

Please download the latest software from our website. Wiedamark.com

and

LED Studio

For this user manual, [LED Studio] was used with [Version 10].

The software's user manual comes with the network control system.

Please download the latest software from our website. Wiedamark.com

2. SAFETY INSTRUCTIONS

CAUTION!&

Be#careful#with#your#operations.#With#a#dangerous#voltage#you#can#suffer#a#dangerous#

electric#shock#when#touching#the#wires!#

This device has left our premises in absolutely perfect condition. In order to maintain this

condition and to ensure asafe operation, itis absolutely necessary for the user to follow the

safety instructions and warning notes written in this user manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do

not switch it on immediately. The arising condensation water might damage your device. Leave

the device switched off until it has reached room temperature.

Please make sure that there are no obvious transport damages. Should you notice any damages

on the AC connection cable or on thecover, do not take thedevice into operation and

immediately consult your local dealer.

This device falls under protection-class II and features aprotective insulation. The voltage and

frequency must exactly bethesame asstated onthedevice. Wrong voltages orpower outlets

can lead to the destruction of the device and to mortal electrical shock.

Always plug in the power plug least. The power plug must always be inserted without force. Make

sure that the plug is tightly connected with the outlet.

Never let the power-cord come into contact with other cables! Handle the power-cord and all

connections with the mains with particular caution! Never touch them with wet hands, as this

could lead to mortal electrical shock.

Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never

operate next to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal

electrical shock.

The cable insert or the female part in the device must never be strained. There must always be

sufficient cable to the device. Otherwise, the cable may be damaged which may lead to mortal

damage.

Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device

and the power-cord from time to time.

If extension cords are used, make sure that the core diameter is sufficient for the required power

consumption of the device. All warnings concerning the power cords are also valid for possible

extension cords.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only

handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise,

the cable or plug can be damaged leading to mortal electrical shock. If the power plug or the

power switch is not accessible, the device must be disconnected via the mains.

If the power plug or the device is dusty, the device must be taken out of operation, disconnected

and then be cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal

electrical shock. More severe dirt in and at the device should only be removed by a specialist.

There must never enter any liquid into power outlets, extension cords or any holes in the housing

of the device. If you suppose that also a minimal amount of liquid may have entered the device, it

must immediately

be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device

is still running, the device must be checked by a specialist if the liquid has reduced any insulation.

Reduced insulation can cause mortal electrical shock.

There must never be any objects entering into the device. This is especially valid for metal parts.

If any metal parts like staples or coarse metal chips enter into the device, the device must be

taken out of operation and disconnected immediately. Malfunction or short-circuits caused by

metal parts may cause mortal injuries.

Keep away children and amateurs!

Never leave this device running unattended.

3. OPERATING DETERMINATIONS

The flexible displays of the LSD series, quipped with extremely bright tri-color RGB LEDs, type

SMD 5050,

were specially designed for projection of videos and graphics synchronous to the computer. The

dispalys are made of bendable and foldable PVC material and can be easily suspended from

truss systems. The modular design allows the horizontal and vertical built-up of video screens,

indoor and outdoor. Control is via special PC software and network components (optionally

available).

This product is only allowed to be operated with the voltage given on the type plate.

This device is splash-proof (IP 44) and therefore qualified for indoor and outdoor use. For outdoor

use, the installer must always make sure to connect a rubber cable HO5RR-F. All valid

instructions concerning the installation of cables outdoors or in the ground must be adhered!

The ambient temperature must always be between -10° C and +45° C. Keep away from direct

insulation (particularly in cars) and heaters. The maximum relative humidity is 100 % with an

ambient temperature of 25° C. This device must only be operated in an altitude between -20 and

2000 m over NN.

Do not shake the device. Avoid brute force when installing or operating the device.

Before installing the system, make sure that the installation area can hold a minimum point load

of 4 times the system's load (e.g. weight 20 kg -point load 80 kg).

For overhead use (mounting height >100 cm), always secure the installation with an appropriate

secondary safety element (e.g. steel rope).

Make sure the area below the installation place is cordoned off when rigging, derigging or

servicing the device.

Do not connect displays to the mains while they are folded.

The F-symbol means: this device can be installed on normal inflammable surfaces.

The symbol determines the minimum distance from lighted objects. The minimum

distance between light output and the illuminated surface must be more than the given value.

The maximum ambient temperature Ta must never be exceeded.

Never use solvents or aggressive detergents in order to clean the device! Rather use a soft and

damp cloth.

Please consider that unauthorized modifications on the device are forbidden due to safety

reasons!

If this device will be operated in any way different to the one described in this manual, the product

may suffer damages and the guarantee becomes void. Furthermore, any other operation may

lead to dangers like shortcircuit, burns, electric shock, lamp explosion, etc.

4. COMPONENTS OF A DISPLAY

e following describes all the components needed to operate an LED display. Some of the components are

used for other products as well.

1. Suspension point

2. Support bar

3. Data signal inputs (15-pin DIN plugs) for connec-

tion to the AIO network interface/receiver interface or

the previous display (number varies for each model)

4. Power cable for connection to a power outlet (90

- 260 V ~, 50/60 Hz) via the power plug or to the

feedthrough output of a previous display via the 2-pin

plug

5. 2-pin jack for the power supply (5 V DC) of the

AIO network interface/receiver interface

6. Front of the display, equipped with

tri-color RGB LEDs, type SMD 5050

7. Press buttons and hook-and-loop connectors

8. Feed-through output (2-pin jack with cap under the

protective cover) for power supply of the subsequent

display

9. Data signal outputs (15-pin DIN jacks) for connect-

ing a subsequent display

(number varies for each model)

10. Belts with hook, have combined

Working Load Limit (WLL) of 79 lbs (36 kg)

4.2 All-in-one network control system LED Show T9

AIO network interface and control soware LED Show T9

is complete set consisting of network interface and the control soware [LED Show T9] allows for control

of the displays together with a Windows PC and a gigabit ethernet network card (1000 Mbps). is system

does not require a further video card with DVI output, which makes it ideally suitable for mobile use with a

notebook. e transmission of the data signals with a screen resolution of up to 1280 x 1024 pixels from the

computer to the network interface is done via the supplied network cable. If needed, a standard CAT5e

network cable up to 100 meters long may be used.

For connecting displays the network interface oers eight data signal outputs, each allows control of 128

(width) x 16 (height) pixels. So one network interface can control 128 (width) x 128 (height) pixels in total. A

conguration with 256 (width) x 128 (height) pixels is also possible, however, results in a lower grayscale

resolution and data refresh rate. To built-up a large video wall with several displays (up to 1280 (width) x

1024 (height) pixels are possible), the network interfaces can be connected in series via network cables.

Minimum system requirements

• Windows 2000/XP

• Dual-core CPU >1.8 GHz

• >1 GB disk space

• Separate gigabit ethernet connection (1000 Mbps)

• 1024 x 768 screen resolution

Recommended system requirements

• 2.9 GHz dual-core CPU

• 4 GB disk space

• Realtek network card with RTL chip

00061810.DOC, Version 2.1

9/47

Block diagram

4-3 Block diagram LED Show T9

Connections of the AIO network interface

4-4 AIO network interface

Pixel control

per data cable 128 (width) x 16 (height) pixels

per AIO network interface 128 (width) x 128 (height) pixels

1Data signal outputs (15-pin DIN jacks)

1to 8 for connection to the displays

2POWER indicator

3Button Test mode for function tests

4Ethernet connection 2 (RJ45 jack),

feed-through output for connection to a

subsequent AIO network interface

5Ethernet connection 1 (RJ45 jack),

input for connection to the ethernet

network output (1000 Mbps are

required) of a computer or the previous

AIO network interface via the supplied

network cable

6Signal indicator, flashes constantly

when the data link is established

72-pin plug for connection to a display

for power supply (5 V DC) of the AIO

network interface

4.3 Network control system LED Studio

Receiver interface and PCI sending card or external DVI sending

card, each with LED Studio control soware

Control system consisting of receiver interface and PCI sending card with the control soware [LED Studio].

Contrary to the all-in-one network control system [LED Show T9], a computer with DVI output card and dual

display mode is required. e DVI output is connected to the sending card DVI input and then transmitted to

the receiver interface via the ethernet connectors. Alternatively to the PCI sending card a sending card with

external housing is available which makes the system perfect for rental use and mobile applications.

For connecting displays the receiver interface oers eight data signal outputs, each allows control of

128 (width) x 16 (height) pixels. So one receiver interface can control 128 (width) x 128 (height) pixels in

total. A conguration with 256 (width) x 128 (height) pixels is also possible, however, results in a lower

grayscale resolution and data refresh rate. To built-up a large video wall with several displays (up to 1280

(width) x 1024 (height) pixels are possible), the receiver interfaces can be connected in series via network

cables.

Minimum system requirements

• Windows 98/me/2000/NT/XP/Vista/ 7

• Video card with dual display mode and DVI output

• Free PCI slot

• Free USB port

Recommended system requirements

• 1024 x 768 screen resolution

• 2.9 GHz dual-core CPU

• 4 GB disk space

00061810.DOC, Version 2.1

11/47

Block diagram

4-8 Block diagram LED Studio

Connections of the PCI sending card

4-9 PCI sending card

Status LEDs,red: power supply failure,

green: normal working mode

Gigabit ethernet outputs (RJ45 jacks)

for connection to a receiver interface

left jack = U,right jack = D

Input for power supply (5 V DC) from

an external source (optional accessory)

with low-voltage plug (center contact =

positive pole)

Only used if the sending card is

operated externally of a computer

USB port for connection to the USB

port on the computer via the supplied

adapter cable

DVI input for connection to the DVI

output on the computer via the supplied

DVI cable

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wiedamark Monitor Handbücher

Wiedamark

Wiedamark Galaxias Series Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung