Wildfire LT-150 series Bedienungsanleitung

LT-150 Series

Table of Contents

Introduction 3

Safety Statements 3

Specifications 4

Setup & Operation 5

Unpacking 5

Installation 5

Operation 5

Maintenance 6

Lamp Replacement 6

Interchanging Reflectors 6

Cleaning 6

Troubleshooting 6

Diagrams 7

Isometric & Line Views 7

Exploded View 8

PartList 9

Schematic 10

Spectral Transmission Graph 11

Photometrics Chart 11

Limited Warranty 12

Introduction

Congratulations on your purchase of a Wildfire Long-Throw 150 UV-A Lighting Fixture, legendary performance

in an affordable compact size featuring lightweight, energy efficient electronic ballasting for flicker and noise free

operation and versatile interchangeable reflectors for a wide variety of configurations. Additional safety features

include automatic lamp failure shutdown, high temperature shutdown and hot re-strike protection. Please take a

moment to read this manual thoroughly before attempting to operate this fixture. Improper set-up, use or

servicing may cause damage to the fixture and/or lamp and void the unit’s warranty.

Safety Statements

CAUTION – RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION, DO NOT OPERATE WITHOUT

COMPLETE LAMP ENCLOSURE IN PLACE, OR IF FILTER GLASS LENS IS DAMAGED

DANGER – INTENSE HEAT. AVOID CONTACT BY PERSONS AND MATERIAL.

CAUTION – RISK OF ELECTRICAL SHOCK AND FIRE. DISCONNECT FIXTURE BEFORE RELAMPING.

USE WITH MAX 250W LAMP TYPE M58 (WILDFIRE IRONARC MODEL LMP-250D). DRY LOCATIONS

ONLY. NOT FOR RESIDENTIAL USE.

WARNING – THIS FIXTURE CONTAINS A HIGH INTENSITY UV METAL HALIDE LAMP, WHICH IS SAFELY

CONTAINED WITHIN AN INTERLOCKING HOUSING. WHEN THIS FIXTURE IS USED IN ACCORDANCE

WITH THE MANUFACTURERS OPERATING INSTRUCTIONS, NO HAZARDS EXIST TO MOST PEOPLE

STANDING WITHIN THE BEAM OF THE FIXTURE. HOWEVER, INDIVIDUALS SUFFERING FROM A RANGE

OF SUNLIGHT EXPOSURE DISORDERS, APHAKIC AND PSEUDOAPHIKIC, OR THOSE INDIVIDUALS

RECEIVING PHOTOSENSITIVE MEDICATION MAY RECEIVE DISCOMFORT IF EXPOSED TO

ULTRAVIOLET LIGHT.

HG – THE LAMP IN THIS FIXTURE CONTAINS MERCURY. MANAGE IN ACCORDANCE WITH DISPOSAL

LAWS. SEE: WWW.LAMPRECYCLE.ORG OR CALL 1-800-937-8065

Specifications

Ballast:

Electronic, Power Factor > 92%

Rating:120-277VAC / 50-60Hz. / 2.5 Amps Max / 150W

Ballast Features:

Flicker & Noise Free

Automatic Lamp Failure Shutdown

Automatic High Temperature Shut Down

Automatic Hot Re-strike Prevention

Circuit Protection:

3 Amp Magnetic Over-current Breaker Switch

Lamp: Wildfire IronArc™ 150 Watt Metal Halide Model LMP-150S (1000 Hr. Rated)

Beam: LT-150F: 90°

LT-150WS: 50°

LT-150F: 20°

Reflector:

Spun Ultra Bright Aluminum

Lens: 6” Round Tempered Borosilicate UV-A Filter Glass

6” Round Clear Boro Float Front Glass (Optional)

Peak Spectral Transmission:

350-365nm

Optimum Operating Temperature:

+50°F to +120°F

Weight:

14.30Lbs. / 6.48kg.

Dimensions:

7.88” / 20.01cm High x 7.38” / 18.75cm Wide x 12” / 30.48cm Long

Accessory Bracket:

7.5” / 19.05cm

Standard Equipment:

Lamp (139-001)

Quick Trigger Pipe Clamp (147-020)

Safety Cable (147-002)

Optional Accessories:

7.5” Barn Door (146-001)

8” DMX Dowser (147-003)

8” DMX Iris (145-001)

Floor Stand (147-007)

Specifications subject to change without notice

Setup & Operation

Unpacking

Unpack the fixture and carefully inspect for any signs of physical damage. Report any damage to Wildfire or

your local distributor immediately. Included with each unit should be the following items:

1. Pipe mounting clamp, designed to attach the fixture to a 11/2” to 2” pipe truss

2. Safety Cable, provided to secure the fixture when mounted on a pipe truss

3. Wildfire IronArc™ Lamp, Model LMP-150S

Before mounting the fixture you will need to install the lamp. refer to Lamp Replacement on page 6 for correct

installation.

Installation

After installing the lamp place the fixture in desired location. The fixture is equipped with a yoke assembly for

mounting. The yoke may be fitted with either a pipe clamp (included) for mounting on a pipe truss or a baby bail

block or junior pin for mounting on a light stand.

If the fixture is mounted on a pipe truss, be sure to use the included safety cable, looping it through the yoke

assembly and around the pipe truss. This will prevent the fixture from falling and causing possible injury in the

event that the pipe clamp was not securely tightened.

To adjust the angle of the fixture, loosen the knobs on either side of the unit slightly, rotate to desired angle and

tighten. Care should be taken to support the front of the fixture while loosening the knobs to prevent the fixture

from rotating forward and causing possible injury.

The fixture comes standard with a 7.5” Bracket assembly for attaching dowsers and scrollers such as Wybron’s

Eclipse or Coloram Series, as well as barndoors and other accessories. When using accessories with this

fixture, be sure to attach the safety cable provided by the accessory manufacturer to the fixtures yoke assembly.

Plug the fixture into the appropriate power source. If you are controlling the unit with a lighting control board, you

will need to make sure it is plugged into a non-dim circuit. If the fixture is plugged into a dimmable circuit, it will

not operate.

Operation

To strike the fixture push the power/breaker switch to the on position. After striking the lamp allow at least 2

minutes for the lamp to get to full brightness. Once the fixture has been powered up and the lamp has ignited if

you shut it off you will need to wait approximately 5 minutes to allow the lamp to cool before the fixture can re-

strike.

If the power/breaker switch is left in the on position during the cool down period, the hot re-strike prevention

circuitry in the ballast will prevent the lamp from striking until it is completely cooled. Once it has cooled

sufficiently, it will strike automatically. This fixture is also equipped with automatic lamp failure protection circuitry

that shuts the fixture down if the lamp should fail for any reason, preventing any damage to the fixture. In

addition there is high temperature protection circuitry that shuts the fixture down if the ballast case temperature

exceeds 85° C. When the fixture cools it will strike again automatically.

Maintenance & Troubleshooting

Lamp Replacement

Unplug the fixture. Remove any accessories from the front. Make sure the fixture is cool to the touch before

opening the front lens assembly cover. Unhook the clasps on either side of the fixture allowing the front lens

assembly cover to swing down. Although the LT-150 Series is designed to allow you to replace the lamp while

the reflector is still in place the procedure is easier when the reflector is removed enabling full access to the

socket (See Interchanging Reflectors below). Grasp the lamp in the center and pull forward to remove it from the

socket. If the lamp is difficult to remove rocking it gently from side to side will help loosen it from the socket.

Reverse this procedure to install the new lamp. Care should be taken not to touch the new lamp directly. Use a

cloth or glove when handling. If you have touched the lamp, it must be cleaned with alcohol to remove any oils

and fingerprints prior to striking. For maximum UV-A output, always use Wildfire IronArc™ lamps, and change

the lamp in your fixture every 1000 hours.

Interchanging Reflectors

There are three different interchangeable reflectors available for the LT-150 Series, a 20° Spot (125-005-02),

50° Wide Spot (125-006-02) and 90° Flood (125-007-02). These reflectors are designed to be removed and

replaced while the lamp is still in the fixture. To remove the reflector, unplug the fixture and remove any

accessories from the front. Make sure the fixture is cool to the touch before opening the front lens assembly

cover. Unhook the clasps on either side of the fixture allowing the front lens assembly cover to swing down.

Loosen the four set screws securing the reflector to the brackets on either side of the lamp housing and slide the

reflector forward out of the housing. Reverse this procedure to install the new reflector. The reflector attachment

brackets are stamped with S, WS and F indicating the proper set position for each reflector.

Cleaning

For best performance, the reflector, lamp and filter lens should be kept free of dirt and dust. At no time should

any cleaning chemicals or abrasives be used to clean any part of the fixture. Do not spray or apply any liquid

directly to any part of the fixture. Always unplug the unit before cleaning. For normal cleaning, a dry soft cloth

should be used to wipe any surface free from dust and light dirt. Cleaning the reflector will require that the lamp

be removed. Remove the lamp by following the instructions listed under lamp replacement above. Once the

lamp has been removed, gently wipe off the reflector using a soft dry cloth. In the event the reflector is heavily

soiled, lightly dampen the cloth with a mild window cleaning agent and wipe clean. The filter lens can be cleaned

in the same manner. The lamp should be cleaned with alcohol only.

Troubleshooting

The fixture will not strike: – Check to make sure there is power to the fixture. Make sure the power/breaker

switch on the back of the fixture has not been tripped. Unplug the unit. Check to see if it has a lamp installed

and that it is seated properly in the socket (See Lamp Replacement above). Check to see if the safety cutoff

switch is making contact by closing the lens cover and listening for a clicking sound. If the fixture still is not

striking, try replacing the lamp. If you have checked all of the above and the fixture still won’t strike, contact

Wildfire technical support at (310) 755-6780 or your local distributor.

The effect is not working anymore: – Try changing the lamp. The lamp in your Wildfire fixture is rated at 1000

hours. This does not necessarily mean that the lamp will “burn out” or not light after 1000 hours. It may continue

to burn for much longer period of time; however, the amount of UV it produces will be reduced considerably

causing the effect to appear as though it isn’t working. For maximum effect Wildfire recommends changing the

lamp every 1000 hours.

Isometric & Line Views

Diagrams

16.87"

13.87"

7.00"

12.00"

7.87"

7.37"

10.75"

Exploded View

27 20

49 24

535254

14 33

Optional Outdoor Kit

Part List

QTY.

PART #

PART NAME

1 1

102-009-01

Housing, Ballast, LT-150 Series

2 1

102-010-01

Housing, Lamp, LT-150 Series

3 1

104-043-03

Control Plate, Rear, LT-250

4 12

121-016

Screw, TD, SM, PHL, PH, #10 x 1" 18-8 SS

5 1

105-001

Circuit Breaker, Carling, 3 Amp

6 1

107-001

Cord, Power, 14 AWG, 9', 120V

7 1

122-003

Strain Relief, Power Cord

8 1

122-002

Jam Nut, Black, 1/2"

9 1

128-015-01

Label, Control, LT-150

10 1

104-049-01

Divider Plate, Lamp, LT-150

11 4

121-068

Standoff, M-F, 8/32 x 5/16" x 3/8"

12 8

121-037

Kepnut, 8-32, 18-8 SS

13 1

104-048-01

Divider Plate, Ballast, LT-150

14 17

121-011

Screw, M, PHL, PH, 8-32 x 3/8", 18-8 SS

15 1

104-074-03

Slide Lock, Accessory

16 1

104-076-01

Housing, Accessory Safety Catch

17 1

118-012

Spring, .25 OD, 1.25 Long, Century# F-14

18 2

121-058

Washer, Flat, .281 ID, .734 OD, .063 Thk, SS

19 4

121-061

Washer, Tooth, #8, 18-8 SS

20 1

104-016-01

Bracket, Switch Rod, Retaining

21 1

104-020-02

Rod, Switch, LT-250F & WS

22 2

104-075-01

Bushing, Wire & Switch Routing

23 1

105-010

Switch, Safety Interlock

24 10

121-005

Screw, M, PHL, PH, 6-32 x 1/4" 18-8 SS

25 2

118-002

Draw Latch

26 2

118-003

Catch, Secondary, Draw Latch

27 1

139-001

Lamp, MH, IronArc, SE, UV, 150W

QTY.

PART #

PART NAME

28 1

108-002

Socket, Lamp, G12 Base, 150W

29 2

121-069

Screw, M, PHL, PH, 8-32 x 3/4", 18-8 SS

30 1

110-011

Ballast, MH, Electronic, 120-277V/50-60Hz/150W

31 3

121-059

Washer, Flat, #8, 18-8 SS

32 4

121-020

Screw, M, TMB, 8-32 x 3/8" 18-8 SS

33 2

104-006-01

Bracket, Reflector Mount

34 1

125-005-02

Reflector, LT-150S

35 1

125-006-02

Reflector, LT-150WS

36 1

125-007-02

Reflector, LT-150F

37 4

121-004

Screw, M, PHL,FH, 5-40 x 3/8"

38 1

118-001

Hinge, Soss, #101, Chrome

39 2

121-039

Nut, SP, 8-32 18-8 SS

40 1

104-002-01

Bracket, Soss Hinge

41 2

121-013

Screw, M, PHL, PH, 8-32 x 1/2" 18-8 SS

42 1

103-001-09

Lens Door, 6" Round, LT-250

43 1

147-002

Cable, Safety, 1/8"

44 1

147-020

Clamp, Quick Trigger Slimline, Black

45 2

120-001

Knob, Yoke Adjustment, LT-Series

46 2

103-006-01

Spacer, Yoke Assembly

47 2

121-032

Rivet Nut, Blind, 16 x 3/8"

48 1

104-032-05

Yoke, LT-250 & LT-150

49 1

104-026-01

Screen, Safety, LT-250

50 1

123-003

Lens, Mug 2, 6" Round

51 4

104-080-01

Clip, Filter Restraining

52 1

105-004

Hexseal, APM, Curcuit Breaker (Opt. Outdoor Kit Only)

53 1

124-003

Lens, Clear Boro Float, 6" Round (Opt. Outdoor Kit Only)

54 16

127-001-01

Gasket, LT-250 (F)(WS)(S) (Opt. Outdoor Kit Only)

Schematic, LT-150 Series

SAFETY SWITCH

POWER SWITCH / CIRCUIT BREAKER

120-277V

COM

GRND

LAMP

150W

150W ELECTRONIC BALLAST

LAMPGROUND

WHITE

GREEN

BLACK

WHITE

BLACK

GREEN

BLUE

GREEN

RED

Inhaltsverzeichnis

Andere Wildfire Leuchte Handbücher

Wildfire

Wildfire LONG-THROW WF-252F1 Bedienungsanleitung

Wildfire

Wildfire Effects Master EM-44V Bedienungsanleitung

Wildfire

Wildfire EM-23S Bedienungsanleitung

Wildfire

Wildfire Long-Throw WF-401F Bedienungsanleitung

Wildfire

Wildfire LT-400F1 Bedienungsanleitung

Wildfire

Wildfire EffectsMaster EM-22L Bedienungsanleitung

Wildfire

Wildfire UltraBlade UB-44 Bedienungsanleitung

Wildfire

Wildfire Long-Throw WF-402FF Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung