Williams Sound Personal PA Value Pack System Leitfaden

Personal PA™Value Pack System

Wide-Band FM Wireless Listening System

MANUAL AND USER GUIDE

MAN 121B

Transmitter Model T17

Receiver Model R35

Optional Receiver Model R35-8

Model PPA VP

PERSONAL PA™VALUE PACK SYSTEM, MODEL PPA VP

INSTALLATION GUIDE & USER MANUAL

CONTENTS PAGE

System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

System Controls and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

T17 Transmitter Set-Up and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Audio Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Using a Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Turning Off DC Microphone Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Transmitter Frequency Change Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Recycling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Receiver Use Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

R35 Receiver Use Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

R35 Receiver Frequency Change Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

R35-8 Receiver Use Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Using A Receiver With A Hearing Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Receiver Management Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Battery Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

SYSTEM OVERVIEW

Thank you for purchasing the Personal PA Value Pack System from Williams Sound Corporation.

The PPA VP System is a Wide-Band FM Listening System which operates in the 72-76 MHz

frequency band. Designed for hearing assistance in places of public access, the PPA VP is for

those who need help overcoming background noise, reverberation, or distance from the sound

source. The versatile PPA VP is easily integrated with your existing sound system or can be used

with a microphone as a stand-alone system.

The system has two principal parts: the T17 Transmitter and the R35 Receiver. Much like a

miniature radio station, the Transmitter and microphone pick up the sounds you want to hear and

broadcast them over an FM radio signal. The receivers are used to pick up the broadcast up to

500 feet away.

To avoid difficulties, please read through these instructions as you begin to use the system. Then

save the manual for questions that arise as you continue to use your PERSONAL PA Value Pack

System.

If you have any problems with this Williams Sound product, don’t hesitate to call us toll-free at

1-800-843-3544.

Sound System Amplifier

Loudspeakers

Microphones

Line-Level Output

R35 Wide-band

Receivers w/Earphones

Line-Level Input

T17 Transmitter

FIGURE 1: OVERALL SYSTEM DIAGRAM

FIGURE 3: R35 RECEIVER CONTROLS

Earphone Jack

Mono 3.5 mm mini earphone

and jack.

Off/On Indicator Light

Green LED indicates receiver

is “on” when lit. Red LED

indicates low battery

Volume/On-Off Control

Combination volume and on-off

thumb wheel control.

Mic

Williams Sound

Auditory Assistance Transmitter

Level Audio

Williams Sound Corp., Minneapolis, MN, USA

12 VAC

100 mA

Antenna Power Audio In

75 Ohm

Hi-Z

Line

Made in U.S.A

FM Transmitter Model PPA T17

FIGURE 2: T17 TRANSMITTER CONTROLS

Mic Input

3.5 mm mini phone jack for use

with Williams Sound condenser

microphones. Supplies +DC

power for condenser

microphones.

Level Control

Screwdriver-adjust control used

to set the microphone input level

or the audio input level.

ON Indicator Light

Glows when power is applied

to the transmitter. There is no

on/off switch. The T17 is

designed to be left on

continuously.

Audio Indicator Light

Flashes when audio signal is

present.

Audio Input

An RCA-type jack for

connecting the transmitter to

other sound systems. Accepts

line-level, unbalanced audio

inputs.

Power Input Jack

Connects to the plug on the wall

transformer power supply.

Antenna Output

Connector

This connector is defeated,

as specified by FCC Rules.

To use the ANT 005 remote

antenna, contact your dealer

or Williams Sound.

Antenna Mounting

Stud

(Top Panel)

For use with the “rubber

duckie” type antenna supplied.

SYSTEM CONTROLS AND FEATURES

T17 TRANSMITTER FRONT PANEL

MIC INPUT:

3.5 mm mini phone for use with Williams Sound condenser microphones. Supplies +DC power

for condenser microphones.

LEVEL CONTROL

Screwdriver-adjust control used to set the microphone input level or the audio input level.

ON INDICATOR LIGHT

Glows when power is applied to the transmitter. There is no on/off switch. The T17 is designed to

be left on continuously.

AUDIO INDICATOR LIGHT

Flashes when audio signal is present.

T17 TRANSMITTER TOP PANEL

ANTENNA MOUNTING STUD

For use with the “rubber duckie” type antenna supplied with the T17.

T17 TRANSMITTER REAR PANEL

POWER INPUT JACK

Connects to the plug on the wall transformer power supply.

AUDIO INPUT

An RCA-type jack for connecting the transmitter to other sound systems. Accepts line-level,

unbalanced audio inputs.

ANTENNA OUTPUT CONNECTOR

This connector is defeated, as specified by FCC Rules. To use a remote antenna, contact your

dealer or Williams Sound.

RECEIVER MODEL R35

EAR JACK

3.5 mm mini earphone jack

OFF/ONINDICATOR LIGHT

Green LED which indicates receiver is “on” when lit. If the batteries are near end of life, the ON

indicator will illuminate red.

VOLUME/ON-OFF CONTROL

Combination volume and on-off rotary control.

RECEIVER MODEL R35-8

EAR JACK

3.5 mm mini earphone jack

OFF/ONINDICATOR LIGHT

Green LED which indicates receiver is “on” when lit. If the batteries

are near end of life, the ON indicator will illuminate red.

VOLUME/ON-OFF CONTROL

Combination volume and on-off rotary control and channel

selection knob.

T17 TRANSMITTER SET-UP AND INSTALLATION

STEP 1: INSTALL THE ANTENNA

The “rubber duckie” whip antenna fits into the hole on top of the transmitter and threads onto a

mounting stud inside. Guide the antenna onto the stud and turn it clockwise to tighten. Do not use

excessive force to tighten the antenna. It only needs to be “finger-tight.”

STEP 2: CONNECT THE TRANSMITTER TO POWER

The T17 is supplied with a wall transformer power supply. Plug the transformer into a 120 V, 60

Hz wall outlet. Then plug the power cord into the “Power” connector on the rear panel of the T17.

The green indicator light on the front panel of the T17 should glow when the power is connected.

There is no on/off switch. The T17 is designed to be continuously on. The wall transformer can

be plugged into a switched outlet that turns on when the other sound equipment is turned on. If

turning the T17 on creates a hum or buzz in the sound system, see the Troubleshooting section on

page 16.

STEP 3: MAKE AUDIO CONNECTIONS

3A: (IF YOU WILL BE USING THE T17 WITH ITS OWN MICROPHONE AS A STAND-ALONE SYSTEM)

Any Williams Sound microphone with a 3.5 mm mini phone plug can be used with the T17.

Plug the microphone into the “Mic” jack on the front panel of the T17.

The T17 is designed to supply positive DC voltage to the plug tip of 2-wire, “barefoot”

electret (power condenser) microphones. If you will be using the T17 with a non-Williams

Sound, Lo-Z (dynamic) microphone, this DC power should be turned off. (See page 7.) If you

use both the Microphone input and the Audio Input on the T17, the signals will be mixed

together.

3B: (IF YOU WILL BE USING THE T17 WITH AN EXISTING SOUND SYSTEM)

Refer to the figure 1 on page 3. Use the audio cable supplied to connect the T17 “Audio In”

jack to an appropriate audio output jack on the sound system mixer or amplifier. The T17 is

designed to work with an unbalanced, line-level audio signal. Suitable connections are:

Choice 1: TAPE OUT or LINE OUT Jack

Choice 2: BOOSTER or BRIDGING Jack

Choice 3: Speaker Terminal, 8 Ohm Tap

If your amplifier or mixer does not have RCA-type connectors, you can obtain adapters from

your Williams Sound Authorized Dealer or a local radio parts store. If the TAPE OUT jack is

already in use, a Y-Cord can be used to connect the T17 and a second device to the same jack.

STEP 4: TEST THE SYSTEM

Use a receiver to test the system and set the input level control. See the section, Receiver Use

Instructions.

TURNING OFF DC MICROPHONE POWER

The T17 is designed to supply positive DC voltage to the plug tip of 2-wire, “barefoot” electret

(power condenser) microphones. If you will be using the T17 with a non-Williams Sound, Lo-Z

(dynamic) microphone, this DC power should be turned off. (See Figure 4.) If you use both the

Microphone input and the Audio Input on the T17, the signals will be mixed together.

Step 1: Unplug the power cord from the T17 and remove its antenna.

Step 2: Use a phillips-type screwdriver to loosen the two screws on the rear of the

Transmitter. Remove the cover. Slide the circuit board out of the case.

Step 3: Use the diagram to locate the HD4 Jumper. This black jumper is also labeled on the

T17 circuit board.

Step 4: Pull the HD4 Jumper off the two pins it connects. DO NOT MAKE ANY OTHER

ADJUSTMENTS! For handy storage, simply turn the jumper sideways and place it

on just one of the two pins.

Step 5: Re-assemble the Transmitter.

Front

FIGURE 4: TURNING OFF DC MICROPHONE POWER

HD4 Jumper Location

This black jumper is also labeled on the T17

circuit board

Front

FIGURE 5: LOCATING FREQUENCY SWITCHES

Frequency Switches

FREQUENCY CHANGE INSTRUCTIONS

Normally, the PPA VP’s factory-set channel (usually 72.9 MHz) requires no change. However, if

another hearing assistance system or authorized radio service is operating on 72.9 MHz in your

area, it may prove necessary to use an alternate channel In this event, the PPA VP’s operating

frequency can easily be changed to an alternate channel to avoid interference.

TRANSMITTER FREQUENCY CHANGE INSTRUCTIONS:

IMPORTANT: Some cities have other radio services licensed on hearing assistance channels.

Under FCC rules governing hearing assistance, you must yield to them. A list of cities where

other radio services are known to exist is included with the transmitter. Do not use frequencies

that are known to be used by licensed radio services in your city, either if they are on the list or if

you discover one.

Step 1: Unplug the power cord from the Transmitter and remove the antenna.

Step 2: Use a phillips-type screwdriver to loosen the two screws on the rear of the

Transmitter. Remove the cover. Slide the circuit board out of the case.

Step 3: Use the diagram to locate the frequency selector switches on the circuit board.

Locate the switch programming chart on the bottom of the Transmitter case.

FIGURE 6: SETTING THE T17 FREQUENCY SELECTOR SWITCHES

12345678

OFF

Switches set for 72.9 MHz

IMPORTANT: Make sure the FM receiver being used is operating on the same frequency

as the T17 transmitter. See R35 frequency change instructions on page 12.

Step 4: Use a paper clip or small screwdriver (not a pencil point) to move the switches to

correspond with the switch positions on the programming chart. (See Figure 6.)

Select a new frequency at least two channels away from the one you are

experiencing interference on. DO NOT TOUCH ANY OF THE OTHER

ADJUSTMENTS!

Step 5: Re-assemble the Transmitter and plug it in. Connect a tape player or radio to the

transmitter to provide a tuning signal for the receivers.

CAUTION!

RECEIVER SAFETY INFORMATION

HEARING SAFETY

This product is designed to amplify sounds to a high volume level which could

potentially cause hearing damage if used improperly. To protect your hearing and the

hearing of others:

Make sure the volume is turned down before putting on the earphone or headphone before

adjusting the volume to a comfortable level.

Set the volume level at the minimum setting that you need to hear.

If you experience feedback (a squealing or howling sound), reduce the volume setting and

move the microphone away from the earphone or headphone.

Do not allow children or other unauthorized persons to have access to this product.

BATTERY SAFETY AND DISPOSAL

This product is supplied with disposable Alkaline batteries. Do not attempt to recharge

disposable batteries, which may explode, release dangerous chemicals, cause burns, or

other serious harm to the user or product.

PACEMAKER SAFETY:

Before using this product with a pacemaker or other medical device, consult your physician or

the manufacturer of your pacemaker or other medical device.

If you have a pacemaker or other medical device, make sure that you are using this

product in accordance with safety guidelines established by your physician or the

pacemaker manufacturer.

BATTERY SAFETY AND DISPOSAL

Help Williams Sound protect the environment! Please take the time to dispose of your

equipment properly.

Product Recycling for Customers in the European Union:

Please do NOT dispose of your Williams Sound equipment in the household trash. Please take

the equipment to a electronics recycling center; OR return the product to the factory for

proper disposal.

Battery Recycling for Customers in the European Union:

Please do NOT dispose of used batteries in the household trash. Please take the batteries to a

retail or community collection point for recycling.

RECYCLING INSTRUCTIONS

4/10/07

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Williams Sound Konferenzsystem Handbücher

Williams Sound

Williams Sound Sound Plus WIR 950 Fehlerbehebungshandbuch

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung