Winco EHL-2C Bedienungsanleitung

Professional Freestanding

Heat Lamp

Operating Instruction Manual

EHL-2C

Item No. Power Rate Voltage Dimensions (H x W x D)

EHL-2C 500W (2 Bulb)

(250W Each Bulb)

120V~ 60Hz 24.0" x 14.0" x 18.625"

609.6mm x 356.6mm x 473mm

Includes 2 Clear, Infrared

250W/120V Bulbs

BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS

Congratulations on your purchase of this WINCO® commercial equipment. When used as intended and with proper

care and maintenance, you are sure to experience years of reliable operation from this equipment. To ensure best

results, it is important that you read and follow the instructions in this manual carefully. It is important to keep

these instructions in a safe place for future reference.

Professional Freestanding Heat Lamp

Important For Future Reference

Introduction

Congratulations on the purchase of your WINCO® countertop appliance. Please take time to carefully read through this manual to ensure the

machine is operated and maintained properly, to ensure the best possible performance from the product for many years.

WINCO will not accept liability for the following if:

• The instructions in this manual have not been followed correctly.

• Non-authorized personnel have tampered with the machine.

• Non-original spare parts are used.

• The machine has not been handled and cleaned correctly.

• There is any use damage to the unit.

WARNING: IMPROPER INSTALLATION,

ADJUSTMENT, ALTERATION, SERVICE OR

MAINTENANCE CAN CAUSE PROPERTY DAMAGE,

INJURY, OR DEATH. READ THE INSTALLATION,

OPERATION, AND MAINTENANCE INSTRUCTIONS

THOROUGHLY BEFORE INSTALLING

OR SERVICING THIS EQUIPMENT.

CAUTION: THESE MODELS ARE DESIGNED, BUILT,

AND SOLD FOR COMMERCIAL USE ONLY. IF THESE

MODELS ARE POSITIONED SO THE GENERAL PUBLIC

CAN USE THE EQUIPMENT, MAKE SURE THAT

CAUTION SIGNS, WARNINGS, AND OPERATING

INSTRUCTIONS ARE CLEARLY POSTED NEAR EACH

UNIT SO THAT ANYONE USING THE EQUIPMENT

WILL USE IT CORRECTLY AND NOT INJURE

THEMSELVES OR HARM THE EQUIPMENT.

WARNING: A FACTORY AUTHORIZED SERVICE

PROVIDER SHOULD HANDLE ALL MAINTENANCE

AND REPAIR. BEFORE DOING ANY MAINTENANCE

OR REPAIR, ARRANGE FOR SERVICE.

AVERTISSEMENT: TOUTE INSTALLATION, RÉGLAGE,

MODIFICATION, RÉPARATION OU ENTRETIEN

INCORRECT PEUT OCCASIONNER DES DOMMAGES

MATÉRIELS, DES BLESSURES GRAVES OU LA MORT.

LIRE LES INTRUCTIONS D'INSTALLATION, D'UTILISATION ET

D'ENTRETIEN ATTENTIVEMENT AVANT D'INSTALLER OU DE

RÉPARER CET APPAREIL.

ATTENTION: CES MODÈLES SONT CONÇUS, FABRIQUÉS,

ET VENDUS POUR UN USAGE COMMERCIAL SEULEMENT.

SI CES MODÈLES SONT PLACÉS POUR QUE LE GRAND

PUBLIC PUISSE LES UTILISER, ASSUREZVOUS QUE LES

CONSIGNES D’ATTENTION, D'AVERTISSEMENT, ET LES

INSTRUCTIONS D'UTILISATION SOIENT CLAIREMENT

AFFICHÉES PRÈS DE CHAQUE UNITÉ DE SORTE QUE N'IMPORTE

QUEL UTILISATEUR DE L'APPAREIL L'EMPLOIE CORRECTEMENT

ET NE SE BLESSE PAS OU N'ENDOMMAGE PAS L'APPAREIL.

AVERTISSEMENT: UN TECHNICIEN AUTORISÉ PAR

L'USINE DEVRA EFFECTUER TOUT L'ENTRETIEN ET LES

RÉPARATIONS.AVANT DE FAIRE TOUT ENTRETIEN OU

RÉPARATION, VEUILLEZ CONTACTER WINCO.

Please complete this information and retain this manual for the life of the product. For

Warranty Service and/or parts, this information is required. Please see Page 8 for More

information on your Warranty and how to register.

Model Number Serial Number Date Purchased

EHL-2C

Professional Freestanding Heat Lamp

Package Contents

All units come with a Use & Care Manual, warranty registration card and the following:

• EHL-2C unit

• 2 clear, infrared bulbs - 500W (250W ea), 120V

Owners should also ensure that no customers,

visitors or other unauthorized personnel come in

contact with this equipment. It is the responsibility

of the owner and the operator to remain alert to any

hazards posed by the function of this equipment.

If an operator is ever uncertain about a particular

task or the proper method of using this equipment,

they should ask an experienced supervisor.

Unless the operator is adequately trained and

supervised there is a possibility of injury. Owners of

this equipment are responsible to make certain that

this equipment is used properly and safely, and that

all of the instructions contained in this manual are

followed. Adherence to the requirements of local,

state or federal law is required.

Owners should not permit anyone to use this

equipment unless they are over 18 years old,

adequately trained, supervised, and have read and

understood this manual.

To ensure safe installation and operation, please carefully read and understand the following statements.

Table of Contents

Specications....................................................................................... 1

Package Contents ............................................................................... 3

Unpacking the Equipment ................................................................ 4

Function and Purpose ........................................................................ 4

Warning Labels.................................................................................... 4

Installation Guidelines ....................................................................... 4

Safety Precautions .............................................................................. 5

Features ................................................................................................ 6

Operation ............................................................................................. 6

Cleaning the Unit ................................................................................ 6

Troubleshooting.................................................................................. 7

Service & Repair .................................................................................. 7

Warranty............................................................................................... 8

Safety Rules & Information

Unpacking the Equipment

DISPOSE OF ALL PACKAGING MATERIALS IN AN

ENVIRONMENTALLY RESPONSIBLE MANNER.

1. Remove all packing materials and tape, as well as any protective

plastic and cardboard, from the unit.

2. Clean any glue residue left over from the plastic or tape.

3. Place the unit in the desired position and height.

SAVE THE ORIGINAL BOX AND PACKAGING FOR USE IN

PACKAGING AND SHIPPING THE EQUIPMENT IF SERVICES

ARENEEDED.

Function and Purpose

This unit is intended to be used in commercial foodservice operations

only. It is not intended for household, industrial or laboratory use.

Before using this equipment all surfaces should be cleaned and dried

thoroughly (see "Cleaning" section on page 9). Failure to clean

surfaces before using the unit could cause food contamination.

Warning Labels

This manual contains a number of precautions to

follow to help promote safe use of this equipment.

Throughout the manual you will see additional

warnings to help alert you to potential hazards.

Warnings aecting your personal safety are indicated by:

NOTE

NOTE is used to notify users of installation, operation, or maintenance

information that is important but not hazard-related.

Please remember that this manual and the warning

labels do not replace the need to be alert, to properly

train and supervise operators, and to use common

sense when using this equipment.

WARNING

CAUTION

HOT

CAUTION

Installation Guidelines

These precautions should be followed at all times. Failure to follow

these precautions could result in injury to yourself and others.

TO REDUCE RISK OF INJURY OR DAMAGE TO THE UNIT:

1. Read this manual thoroughly before installation and operation.

DO NOT proceed with installation and operation if you have any

questions or do not understand anything in this manual. Contact

your representative or the manufacturer rst.

2. Remove the unit and bulbs from the box. Once your unit has

been removed from the packaging, be certain that all protective

plastics and residues are removed from all surfaces.

3. Select a location for the unit that has a level, solid, non-skid

surface that is nonammable and away from water hazards or

sinks, and is in a well-lit work area.

4. Inspect the unit to ensure all parts have been provided.

5. Proper connections and power supply are essential for ecient

performance.

Proper Grounding

This machine is provided with a

three-pronged grounding plug.

The outlet to which this plug

is connected must be properly

grounded. If the receptacle is not

the proper grounding type, contact

an electrician. DO NOT, under any

circumstances, cut or remove the

third ground prong from the power

cord or use any adapter plug.

USE A GROUNDED OUTLET

DO NOT ADD AN ADAPTOR

TO THE PLUG

6. When using electrical appliances, basic precautions must always

be followed to reduce the risk of re, electric shock and injury.

7. Clean this appliance thoroughly before and after each use. Refer

to cleaning instructions on page 9.

WARNING

Plug heat lamp into grounded outlet with correct

voltage and suﬃcient power capacity. Refer to

Product Identiﬁcation label on the heat lamp for

voltage and wattage requirements. The heat lamp is

designed for use on alternating current (AC) only.

Warnings related to possible damage to equipment are indicated by:

Safety Precautions

xBurn Hazard.

The unit lamp surfaces become HOT during use.

Extreme caution is necessary when the appliance

is left unattended.

USECAUTIONWHENTOUCHINGTHEUNIT.

WARNING

CAUTION

HOT

14. DO NOT pull by the cord to disconnect.

15. NEVER plug equipment in where water oods the area.

16. ALWAYS place the appliance on a rm, stable surface.

CAUTION

Extreme caution is necessary when any appliance is

used by or near children or when the appliance is left

unattended.

17. ALWAYS unplug appliance when not in use and before cleaning,

WARNING

xElectrical Shock Hazard.

Keep water and other liquids from entering the inside

of the unit. Liquid inside the unit could cause an

electrical shock.

Do not spray water or cleaning products. Liquid could contact the electrical

components and cause a short circuit or an electrical shock. Do not use unit if

power cord is damaged or has been modied.

adjusting, or maintaining this product. To disconnect this

appliance, turn switch o and remove plug from power source.

18. ALWAYS allow the unit to cool down to room temperature after

use and before dismantling for cleaning; the unit will be too hot

to handle immediately after use.

CAUTION

This equipment gets HOT. Make sure all

ﬂammable/combustible materials are set

away from this equipment.

TO AVOID SERIOUS PERSONAL INJURY

1. DO NOT

operate the unit before reading the instruction manual rst.

2. ALWAYS disconnect or unplug electrical power before cleaning,

servicing or adjusting any parts or attachments.

3. NEVER

bypass, alter or modify this equipment in any way from its

original condition. Doing so may create hazards and will void warranty.

4. NEVER operate the unit with a damaged power cord or plug.

5. NEVER leave the unit on overnight.

6. NEVER use the unit as a heating source for your kitchen, space,

or room.

CAUTION

IMPORTANT SAFEGUARDS & SAFETY INSTRUCTIONS

When using electrical food equipment, basic safety

precautions should always be followed.

7. DO NOT touch hot surfaces. This appliance is hot when in use. To

avoid burns, do not let bare skin touch hot surfaces.

8. CAUTION: To protect against risk of electrical shock, do not

immerse in water, dishwasher or any other liquid.

9. ALWAYS unplug unit when not in use, before putting on or taking

o parts, and before cleaning.

10. CAUTION: The use of attachments not recommended or sold by

the manufacturer may cause re, electrical shock or injury.

11. DO NOT use outdoors.

12. DO NOT

place on or near a hot gas or electric burner, or in a heated oven.

Keep combustible materials such as drapes and other furnishings away

from appliance.

13. DO NOT use this equipment for any use other than the use

intended by the manufacturer.

Features: EHL-2C

LAMP BAR (Figure 1) Mouting bar for lamp housing.

LAMP HOUSING (Figure 1) Housing for heat lamps

POWER ON/OFF SWITCH (Figure 1) Turns power on/o.

LOCKING NUT (Figure 1) Locks the adjustable main bar in

place to keep heat lamps at optimal height.

MAIN BAR (Figure 1) Raises and lowers height of lamp bar.

LAMP BASE (Figure 1) Wide stance for stability. Standard food

trays will t between base.

RUBBER FEET (Figure 1) Prevent slipping of unit.

Figure 1. EHL-2C Features

Figure 2. EHL-2C Dimensions and Height Adjustments

4 HEIGHT

ADJUSTMENTS

(Tabletop to base of light)

12"

14" D

18 " W

24"

19"

17"

15"

Preparation

1. Set unit on a at surface.

2. Install the Main Bar (E) into the Lamp Base (F).

3. Adjust the Main Bar (E) to appropriate height and insert the

Locking Nut (D) to x the height.

4. Install bulbs with the specied wattage rating as indicated on the

heat lamp.

5. If unit fails to work properly when rst operated, call Winco

customer service @ 1-888-946-2682 or 1-973-916-9958

Operation

BEFOREOPERATINGUNIT,ITSHOULDBECHECKEDTOSEETHAT

IT IS SITTING LEVEL.

1. Plug cord into grounded electrical outlet of the correct voltage.

Electrical shock can occur if appliance is not grounded.

2. Place food products in a pan, located directly under the bulbs for

best results.

3. Turn unit o when not in use.

4. To disconnect appliance, turn switch o and remove plug from

power source.

Cleaning

NOTE

Proper maintenance plays an important part in the life span and

functioning of the heat lamp.

1. Unplug the cord and let heat lamp cool before cleaning or moving.

2. This unit can be cleaned with a damp sponge and mild soap.

Rinse with clean water and wipe dry.

3. Do not immerse in water or other liquid.

Do not clean with a water jet.

Rubber feet are

under lamp base

If your WINCO® Heat Lamp does not operate, please check the following before placing a service call:

Troubleshooting

ISSUE MIGHT BE CAUSED BY RECOMMENDED SOLUTION

Lamps are not on

Unit is not plugged in Make sure unit is plugged in, and power cord is not

broken or damaged

Power switch is o Make sure power switch is in the ON position

Bulb(s) are not screwed in Screw in each bulb - DO NOT over-tighten, this may

damage the bulb(s)

Bulb(s) are burnt out/broken Replace the bulb(s)

Lamps are not heating food Wrong bulb(s) Install 250W HEAT LAMP BULBS Only, not regular

light bulbs

Lamps burn out often

Over tightening the bulb(s) Over tightening the bulbs may cause damage that

will decrease the lifespan of the bulb.

Bulb(s) are not tight enough If the bulb is not in full contact with the screw shell

and socket, it will cause electrical arcing and pitting

of the contact surface, decreasing the lifespan of

the bulb.

Safety

A WINCO® Approved Service Technician should carry out repairs if

necessary. Do not remove any components on this product.

If the power cord is damaged, it must be replaced by a WINCO

Approved Service Technician in order to avoid a hazard.

Service and Repair

To avoid serious injury or damage, NEVER attempt to repair the unit

or replace a damaged power cord yourself.

To initiate warranty service contact: support@wincous.com

or call: 973-295-3899

DO NOT send unit to WINCO® without rst contacting customer

service.

See "Limited Warranty" section on page 8 for more details.

Limited warranty does not cover the EHL-BR or EHL-BW bulbs.

WINCO® warrants to the original purchaser of new equipment that

said equipment, when installed in accordance with our instructions

within North America and subjected to normal use, is free from

defects in material or workmanship for a period of 1 year. The labor

warranty is one year from original installation or 18 months from

actual factory shipment date, whichever date occurs rst.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED. WINCO EXPRESSLY

DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY

OR EXPRESSED OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE.

WINCO’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY

IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING

EQUIPMENT THAT PROVES TO BE DEFECTIVE IN MATERIAL OR

WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD.

IN NO EVENT SHALL WINCO BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY,

INCLUDING, WITHOUT LIMITATION, LOSS OF PROPERTY,

PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER

ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES,

WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY, OR

OTHERWISE.

This warranty is given only to the rst purchaser from a retail dealer.

No warranty is given to subsequent transferees.

Warranty does not cover product failures caused by: failure to

maintain, neglect, abuse, damage due to excess water, re, normal

wear, improper set up and use. Periodic maintenance is not covered.

This warranty is not in force until such time as a properly completed

and digitally signed Installation/Warranty Registration has been

received by WINCO within 30 days from the date of installation.

WARRANTY SERVICE

To initiate warranty service contact: support@wincous.com

or call: 973-295-3899

DO NOT send unit to WINCO without rst contacting our customer

service department.

Limited Warranty

http://support.wincous.com

Proof of purchase is required to extend warranty more than 1 year

from date of shipment from the factory.

THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE

AND EXCLUSIVE STATEMENT BETWEEN THE BUYER AND

SELLER. WINCO NEITHER ASSUMES NOR AUTHORIZES ANY

PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION OR

LIABILITY IN CONNECTION WITH SAID EQUIPMENT.

Examples of items not covered under warranty, but not limited to just

these items:

1. Acts of God, re, water damage, burglary, accident, theft.

2. Freight damage.

3. Improper installation or alteration of equipment.

4. Use of generic or after market parts.

5. Repairs made by anyone other than a WINCO designated

service provider.

6. Lubrication.

7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc.

8. Cleaning of equipment.

9. Misuse or abuse.

WARRANTY REGISTRATION

SCAN THE QR CODE WITH YOUR MOBILE DEVICE

or go to

http://support.wincous.com

TO FILL OUT AND SUBMIT YOUR WARRANTY REGISTRATION.

~ Keep this manual in a safe place for future reference ~

Andere Handbücher für EHL-2C

Inhaltsverzeichnis

Andere Winco Beleuchtungsausrüstung Handbücher

Winco

Winco EHL-2C Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung