Windsor Compass 2 10070560 Bedienungsanleitung

Operating Instructions (ENG)

Multi-Functional Cleaning

MODEL: CMPS2

10070560

CMPS2E

10070570

86305210 –F

02/19/09

MACHINE DATA LOG/OVERVIEW

CMPS2 86305210 11/21/07

OVERVIEW

The Compass 2™is a multi-functional cleaning machine intended for commercial use. The

appliance applies chemical at low pressure and uses high pressure to clean with. Then the soiled

water is vacuumed back into the recovery tank.

Model:

Date of Purchase:

Serial Number:

Sales Representative:

Address:

Phone Number:

TABLE OF CONTENTS

CMPS2 86305210 04/28/08

Machine Data Log/Overview.........................2

Table of Contents..........................................3

HOW TO USE THIS MANUAL

How to use this Manual.................................1-1

SAFETY

Important Safety Instructions........................2-1

Hazard Intensity Level. .................................2-2

Grounding Instructions..................................2-3

Safety Label Location. ..................................2-4

OPERATIONS

Technical Specifications. ..............................3-1

How the Machine Works...............................3-2

Components..................................................3-3

Controls.........................................................3-4

Machine Operation........................................3-6

Chemicals.....................................................3-8

MAINTENANCE

Maintenance. ................................................4-1

Float Shut-Off..........................................4-2

Strainer....................................................4-2

Circuit Breakers.......................................4-2

Vacuum Motor Replacement...................4-3

Solution Pump Replacement...................4-4

Regulating Unloader…………………….. 4-4

Periodic/Daily Maintenance ..........................4-5

Service Schedule..........................................4-5

Machine Troubleshooting..............................4-6

Notes.............................................................4-7

GROUP PARTS LIST

Control Panel................................................5-1

Decal.............................................................5-3

Solution Tank................................................5-5

Solution-Injector Assembly...........................5-7

Solution-Pump..............................................5-9

Recovery Tank............................................ 5-13

Vacuum....................................................... 5-15

Wheels & Frame ........................................ 5-17

Tools – Standard ........................................ 5-19

Wiring – Schematic (120V)......................... 5-21

Wiring – Schematic (230V)......................... 5-23

Suggested Spare Parts............................... 5-23

OPTIONS

Vacuum Hose Rack.................................... 6-1

Grout Cleaner............................................. 6-3

High Pressure Wand................................... 6-5

Carpet Tool................................................. 6-7

Storage Bag................................................ 6-9

Chemical Lock............................................ 6-11

Serial Numbers........................................... 6-13

Warranty

HOW TO USE THIS MANUAL

CMPS2 86305210 04/23/08

1-1

This manual contains the following sections:

- HOW TO USE THIS MANUAL

- SAFETY

- OPERATIONS

- MAINTENANCE

- PARTS LIST

The HOW TO USE THIS MANUAL section will tell

you how to find important information for ordering

correct repair parts.

Parts may be ordered from authorized Windsor

dealers. When placing an order for parts, the

machine model and machine serial number are

important. Refer to the MACHINE DATA box which

is filled out during the installation of your machine.

The MACHINE DATA box is located on the inside of

the front cover of this manual.

The model and serial number of your machine is on

the bottom back-end of the machine.

The SAFETY section contains important information

regarding hazard or unsafe practices of the

machine. Levels of hazards is identified that could

result in product or personal injury, or severe injury

resulting in death.

The OPERATIONS section is to familiarize the

operator with the operation and function of the

machine.

The MAINTENANCE section contains preventive

maintenance to keep the machine and its

components in good working condition. They are

listed in this general order:

- Vacuum Motor

- Solution Pump

- Daily Maintenance

- Periodic Maintenance

- Service Schedule

- Machine Troubleshooting

The PARTS LIST section contains assembled parts

illustrations and corresponding parts list. The parts

lists include a number of columns of information:

- REF – column refers to the reference

number on the parts illustration.

- PART NO. – column lists the part

number for the part.

- PRV NO. - reference number.

- QTY – column lists the quantity of the

part used in that area of the machine.

- DESCRIPTION – column is a brief

description of the part.

- SERIAL NO. FROM – If this column has

an (*) and a Reference number, see the

SERIAL NUMBERS page in the back of

your manual. If column has two asterisk

(**), call manufacturer for serial number.

The serial number indicates the first

machine the part number is applicable

to. The main illustration shows the most

current design of the machine. When a

boxed illustration is shown, it displays

the older design.

-NOTES – column for information not

noted by the other columns.

NOTE: If a service or option kit is installed

on your machine, be sure to keep the

KIT INSTRUCTIONS which came with

the kit. It contains replacement parts

numbers needed for ordering future

parts.

MODEL __________________________________

DATE OF PURCHASE _____________________

SERIAL NUMBER ________________________

SALES REPRESENTATIVE # _______________

CMPS2 86305210 11/21/07 2-1

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution

must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

This machine is for commercial use.

To reduce the risk of fire, electric shock, or injury:

Connect to a properly grounded outlet. See Grounding Instructions.

Do not leave the machine unattended. Unplug machine from outlet when not in use and before

maintenance or service.

Do not allow machine to be used as a toy. Close attention is necessary when used by or near

children.

Do not point spray gun at people.

Use only as described in this manual. Use only manufacturer’s recommended components and

attachments.

Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding

the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or

dropped into water, return it to an authorized service center.

Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord

around sharp edges or corners.

Do not run machine over cord. Keep cord away from heated surfaces.

Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.

Do not handle the electrical plug or machine with wet hands.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce

airflow.

Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

This machine is not suitable for picking up health endangering dust.

Turn off all controls before unplugging.

Machine can cause a fire when operating near flammable vapors or materials. Do not operate this

machine near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals,

factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

If foam or liquid comes out of machine, switch off immediately.

SAVE THESE INSTRUCTIONS

HAZARD INTENSITY LEVEL

CMPS2 86305210 11/21/07

2-2

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR

SAFETY. The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property

damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper

operating condition. Following is information that signals some potentially dangerous conditions to the

operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate

all safety devices on the machine. Please take the necessary steps to train the machine operating

personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and understood.

In Flammable or Explosive areas.

In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the

machine. Use Windsor approved replacement parts.

GROUNDING INSTRUCTIONS

CMPS2 86305210 04/23/08 2-

THIS PRODUCT IS FOR COMMERCIAL USE

ONLY.

ELECTRICAL:

The amp, hertz, and voltage are listed on the data

label found on each machine. Using voltages above

or below those indicated on the data label will cause

serious damage to the motors.

EXTENSION CORDS:

If an extension cord is used, the wire size must be at

least one size larger than the power cord on the

machine, and must be limited to 50 feet (15.5m) in

length.

GROUNDING INSTRUCTIONS:

This appliance must be grounded. If it should

malfunction or break down, grounding provides a

path of least resistance for electric current to reduce

the risk of electric shock. This appliance is equipped

with a cord having an equipment-grounding

conductor and grounding plug. The plug must be

inserted into an appropriate outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

Improper connection of the equipment-

grounding conductor can result in a risk of

electric shock. Check with a qualified electrician

or service person if you are in doubt as to

whether the outlet is properly grounded. Do not

modify the plug provided with the appliance - if it

will not fit the outlet, have a proper outlet

installed by a qualified electrician.

GROUNDING INSTRUCTIONS (120V ONLY)

GROUND-FAULT CIRCUIT-INTERRUPTER

PROTECTION (120V ONLY)

This pressure washer is provided with a

(GFCI) built into the plug of the power supply

cord. This device provides additional protection

from the risk of electric shock. Should

replacement of the plug or cord become

necessary, use only identical replacement parts

that include GFCI protection. If the GFCI is not

the AUTOMATIC RESET TYPE, it must be

manually TESTED and RESET each time the

cleaning system is plugged in. Press firmly to

assure internal spring activates switch. Push

“test“ then push “reset”. Motor will not start if

GFCl does not reset. Check circuit breakers or

outlet. If circuit breaker is not tripped and unit

will not reset, contact local service center.

SAFETY LABEL LOCATION

CMPS2 86305210 11/21/07

2-4

The following WARNING LABEL(S) are found on your cleaning unit. These labels point out important Warnings

and Cautions which should be followed at all times. Failure to follow warnings and cautions could result in fatality,

personal injury to yourself and/or others, or property damage. Follow these instructions carefully! DO NOT

remove these labels.

NOTE: If at any time the labels become illegible, promptly replace them.

PRV NO. 500009

WARNING LABEL 86242230

TECHNICAL SPECIFICATIONS

CMPS2 86305210 04/23/08 3-1

ITEM DIMENSION/CAPACITY

120V, 14A, 60HZ

Electrical 230V, 7A, 50HZ

Electric Pump Motor 1/2hp, 1750rpm

Solution Pump 700psi (48 bars), Axial plunger

Electric Vacuum Motor 2stage, 1.25hp (2.80m3/min.)

Waterlift 82 in. (208 cm)

Solution Capacity 29 gallons (111L)

Recovery Capacity 19 gallons (70L)

Wheels

- Front (2)

- Rear (2)

6 in. dia. (15.24cm) X 1.5

12 in. dia. ( 30.48cm)X 1.75

Dimensions – Weight 205 lb. (93kg)

Dimensions – Length 36 in. (91.4cm)

Dimensions - Height 43 in. (109.2cm)

Dimensions - Width 24.75 in. (62.87cm)

Power Cable 50 ft. (127m) 14 gauge

SPECIAL NOTES:

The sound pressure level at 1m from the machine was measured to be 79 dBA. This was a nearfield,

broadband measurement taken in a typical industrial environment on a tile floor. This appliance

contains no possible source of impact noise. The instantaneous sound pressure is below 63 Pa.

The weighted root mean square acceleration at the operator’s arms was measured to be below

2.5m/s2. This was a tri-axial, third-octave-band measurement made during normal operation on a

composite tile floor. The measurement and related calculations were made in accordance with

ISO 5349-1.

HOW THE MACHINE WORKS

CMPS2 86305210 11/21/07

3-2

The Compass 2™is a multi-functional cleaning

machine intended for commercial use. The

appliance applies chemical at low pressure and

uses high pressure to clean with. Then the

soiled water is vacuumed back into the

recovery tank.

The machine's primary systems are the clean

water system, recovery system, chemical

system and pressure washer system.

The function of the clean water system is to

store clean water and deliver it to the available

tools. The clean water system consists of the

clean water tank and strainer. The clean water

tank stores water until it is delivered to the

tools. The strainer protects the pump from

debris.

The function of the recovery system is to

vacuum the soiled water back into the recovery

tank. The recovery system consists of the

wand and wheeled squeegee, vacuum motor,

float shut-off and recovery tank. The wand and

wheeled squeegee wipes the dirty solution off

the floor. The vacuum motor provides suction

to draw the dirty solution off the floor and into

the recovery tank. The float shut-off protects

the vacuum fan from over filling. The recovery

tank stores the dirty solution.

The function of the chemical system is to

dispense chemical into the clean water system.

The chemical system consists of the chemical

reservoir, chemical cap and a chemical-

metering selector. The chemical reservoir

stores and dispenses chemical into the clean

water system. The chemical-metering selector

meters the amount of chemical and selects

between chemical A or B and turn chemical off.

The function of pressure washer system is to

clean fixtures and other surfaces. The pressure

washer system consists of a pump, high-

pressure hose and spray gun. The pump

delivers cleaning solution to the tools. The

high-pressure hose connects the pump to the

spray gun.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Windsor Bodenreinigungsmaschine Handbücher

Windsor

Windsor LB1500 Bedienungsanleitung

Windsor

Windsor ADMIRAL ADM8IA - 10080010 Bedienungsanleitung

Windsor

Windsor Chariot 2 CBPS20 Bedienungsanleitung

Windsor

Windsor RRB 360 T Bedienungsanleitung

Windsor

Windsor PJ2A Bedienungsanleitung

Windsor

Windsor Commodore 20 Bedienungsanleitung

Windsor

Windsor Sensor XP 18 Betriebsanleitung

Windsor

Windsor STORM SP13 Bedienungsanleitung

Windsor

Windsor NMWU225H Technische Daten

Windsor

Windsor 1.005.293.0 Bedienungsanleitung

Windsor

Windsor SCC172 Bedienungsanleitung

Windsor

Windsor ADMIRAL PLUS ADPJ Bedienungsanleitung

Windsor

Windsor Lightning 1500 Bedienungsanleitung

Windsor

Windsor Dri-Matic Bedienungsanleitung

Windsor

Windsor Powertec 20X Bedienungsanleitung

Windsor

Windsor CLP12 Bedienungsanleitung

Windsor

Windsor LB2000I Bedienungsanleitung

Windsor

Windsor Chariot iScrub Bedienungsanleitung

Windsor

Windsor COMMODORE CMD Bedienungsanleitung

Windsor

Windsor SCEX264 Bedienungsanleitung

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Windsor

Windsor QK32 Bedienungsanleitung

Windsor

Windsor Admiral ADM8I Bedienungsanleitung

Windsor

Windsor Walk Behind Scrubber SCE326 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung

IPC

IPC CT51-71 BT Bedienungsanleitung