Winstars WS-WN518 Bedienungsanleitung
High Power Wi-Fi Repeater
User Manual
Quick Installation Guide(Q.I.G.)
REV.1.2
Introduction：
The Wi-Fi Repeater is a combined wired/wireless network connection
device designed specifically for small business, office, and home office
networking requirements. It allows a wireless network to be expanded using
multiple access points without the need for a wired backbone to link them. It
also works well with other 11b/g and 11n protocol wireless products.
NOTE:If you need to reset the Wi-Fi Repeater, you need press and hold
the reset button inside the tiny hole for 10 seconds.
Package Contents
Before you starting to use this router, please check if there’s anything
missing in the package, and contact your dealer of purchase to claim for
missing items:
•1 x Wireless-N Repeater
•1 x RJ-45 Networking Cable
•1 x Quick installation Guide
reset
WPS
RJ45
Getting Started
Setting up a Wireless Infrastructure Network
For a typical wireless setup at home (as shown below), please do the
following:
Wireless Repeater Mode
You will need WiFi AP/Router
Internet access
Wireless AP Mode
You will need broadband Router
Internet access
Connect the WiFi-Repeater to
your Router/Switch with RJ-45
Cable
How to configure the Wi-Fi Repeater
You can configure the Wi-Fi Repeater by connecting it with your
computer/laptop with enclosed RJ45 cable or wirelessly. We recommend
you to do it with wire.
A. Configure the Wi-Fi Repeater with RJ45 Cable
A1. Plug the Wi-Fi Repeater to a
wall socket. Connect your
computer / laptop with the Wi-Fi
Repeater with enclosed RJ45
Cable.
A2. Click the “Start” button (it
should be located at the lower-
left corner of your screen), then
click “Control Panel”. Click
“View Network Status and
Tasks”, and then click “Manage
Network Connections”. Right-
click “Local Area Network”,
then select “Properties”. When
the “Local Area Connection
Properties” window appears,
select “Internet Protocol
Version 4 (TCP/IPv4)” and then
click “Properties”.
A3. Setting IP address manually:
Type IP address is
192.168.10.x (x is from 2 to
254), and Subnet mask is
255.255.255.0. Type the
Router’s LAN IP address (the
default IP is 192.168.10.1) into
the Default gateway field.
A4. Open web browser and type
http://192.168.10.1 in the
browser's address box. This
number is the default IP
address for this device.
A5. The login screen below will
appear. Enter the “User Name”
and “Password” and click “OK”
to login. The default User name
is “admin” and the Password is
“admin”.
A6. After logging in and click “Setup Wizard”, you will see the web page
below: Select “Wireless Repeater Mode (Station)” and click on
‘Next’ to continue.
A7. Click on ‘Repeater – OneKey Setting’ button
A8. Wait a few seconds and you will see the site below and please click
on ‘Wireless Network Selection’ button.
A9. Click on ‘Refresh List’ button.
Select the Wireless SSID and click ‘Next’ to continue.
A10. When you see the site below, please do not change any setting but
only insert the password of your network.
Click on ‘Apply and Reboot’ button.
A11. Click ‘OK’ to confirm. The Repeater
will restart.
A12. Wait a few seconds and you will see the status site like below. It
means your Wi-Fi Repeater is ready for use.
* The Wi-Fi Repeater1 WLAN key is same with your router.
If you do not see the site like above, you need to re-configure it again.
NOTE:If you need to reset the Wi-Fi Repeater, you need press the reset
button inside the tiny hole for 10 seconds.
B. Configure the Wi-Fi Repeater wirelessly.
1. Plug the Wi-Fi Repeater to a wall socket.
2. Click on the network icon ( or ) on
the right bottom of your desktop. You will
find the signal from the Wi-Fi Repeater.
Click on ‘Connect’ and wait for a few
seconds.
3. Follow process A3 to A12 to configure
your Wi-Fi Repeater wirelessly.
C. Configure the Wireless AP Mode.
1. Plug the Wi-Fi Repeater to a wall socket.
2. Follow process A2 to A5.
3. Select “Standard Wireless AP Mode” and click on ‘Next’ to continue.
4. Click on ‘AP – OneKey Setting’ button
5. Wait a few seconds and you will see the status site like below. It
means your Wi-Fi Repeater is ready for use.
Inhaltsverzeichnis
Andere Winstars Repeater Handbücher
