Wintech TDS560USB PLUS Bedienungsanleitung

IMPORTANT INFORMATION
About This Manual
This Installation Guide is for the TDS560USB PLUS JTAG Emulator
product.
The TDS560USB PLUS JTAG Emulator is a module to be attached to a
PC for hardware engineers and software programmers to develop DSP
applications.
The text paragraphs in this Guide are very important for proper device
functioning and for preventing any possible damages on the Wintech
TDS560USB PLUS JTAG Emulator device and project target board. These
paragraphs are shaded as in the following example. Please carefully read
each of the shaded text.
This is an example of a very important text paragraph.
Related Documents
Code Composer User's Guide(Texas Instruments SPRU296)
Code Composer Studio User's Guide (Texas Instruments SPRU328B)
XDS560 Emulator Technical Reference (Texas Instruments SPRU589)
Using xdsprobe with the XDS560 and XDS510 (Texas Instruments
SPRA758A)

TABLE OF CONTENTS
Introduction...........................................................................1
Overview ..................................................................................................1
Features.....................................................................................................2
Quick Install.........................................................................3
Quick Install Procedures...........................................................................3
The TDS560USB PLUS JTAG Emulator kit contains.............................3
Installation Requirements.........................................................................4
Supports Operating Systems.....................................................................4
Detailed Installation............................................................5
What you will need...................................................................................5
The Hardware Installation........................................................................5
The USB Device Drivers Installation.......................................................6
Installing the TDS560USB PLUS Software.............................................9
Code Composer Studio Setup.................................................................10
Hardware Considerations.................................................15
Recommended Connection Procedure ...................................................15
Recommend Disconnection Procedure...................................................16
JTAG Cable Connection.........................................................................16
XDSRESET and XDSPROBE..........................................17
XDSRESET............................................................................................17
XDSPROBE...........................................................................................17
Appendix A ........................................................................18
Code Composer Studio Setup (OMAP) .................................................18
Appendix B.........................................................................22
Support Information.........................................................23
Contact Information................................................................................23

TDS560USB PLUS Emulator Installation Guide
Introduction
Overview
The TDS560USB PLUS JTAG Emulator is designed to be used with
digital signal processors (DSPs) operating at 1.0-5.0 volts. The emulator
itself is a USB device. It is fully plug and play compatible. The
TDS560USB PLUS JTAG Emulator is designed to operate with TI Code
Composer Studio IDE debug tool and is compatible with
Windows2000/XP/2003 Server.
Figure 1-1
1

TDS560USB PLUS Emulator Installation Guide
2
Features
The TDS560USB PLUS JTAG Emulator has the following key features:
zUSB compatible. Simple Connection, fully Plug-and-Play compatible–
no jumpers, no switch settings
zHot pluggable
zSupports Texas Instruments (TI)DSP with a JTAG (IEEE 1149.1)
interface: C2000, F2400, C27X, F28X, C54X, C55X, C6000, C64X,
TMS470 (ARM) and OMAP platforms
zSupports Texas Instruments Code Composer Studio
zCompatible with XDS510
zIncludes all XDS560PCI features:
·Real-Time data exchange (RTDX) bandwidth over 2 Mb/s
·Real-time event sequence server without stopping the application
zSupports multiprocessor debugging of same or different type
zWide dynamic operating voltage: 1.0 to 5.0 volts
zProgrammable TCK: 500KHz to 35MHz
zIncreasing code download speed up to 8x faster than XDS510
zOverall cable/pod length of 6ft (1.5m)
zHardware detection of power losses and cable disconnects
zAll pod signals are ESD protected

TDS560USB PLUS Emulator Installation Guide
3
Quick Install
Quick Install Procedures
This Guide describes the steps to installing the TDS560USB PLUS JTAG
Emulator in the following order:
1. Install the TDS560USB PLUS JTAG Emulator hardware
2. Install the TDS560USB PLUS JTAG device driver
3. Make sure Code Composer Studio™ IDE is installed on the PC
4. Install the TDS560USB PLUS JTAG Emulator software
5. Configure Code Composer Studio IDE
6. Reset the TDS560USB PLUS JTAG Emulator and Reset the target
DSP
7. Run CCS
The TDS560USB PLUS JTAG Emulator kit
contains
(See Figure 1-1)
• TDS560USB PLUS JTAG Emulator and Pod
•USB interface cable
• 5 Volt DC power supply
• AC power cord
•The TDS560USB PLUS driver disk
•TDS560SB PLUS JTAG Emulator Installation Guide Reference Guide
(this document)

TDS560USB PLUS Emulator Installation Guide
4
Installation Requirements
• Code Composer Studio IDE 2.0 or greater
• A free USB port (USB2.0 is recommended)
• 500MHz or higher Pentium ™-compatible CPU (900MHz or higher
Pentium III CPU or equivalent is recommended)
• Local CD-ROM drive
Supports Operating Systems
• Windows Win2000(SP4) /WinXP(SP1)/ 2003 Server

TDS560USB PLUS Emulator Installation Guide
Detailed Installation
What you will need
The following list details all items needed to install and run with the
TDS560USB PLUS JTAG Emulator.
zPC, with a free Universal Serial Bus (USB) port
zThe TDS560USB PLUS JTAG Emulator
zThe TDS560USB PLUS driver disk
zUSB interface cable
zDSP target system
zCode Composer Studio
The Hardware Installation
zRemove power from the target DSP system
zAttach the keyed TDS560USB PLUS JTAG Emulator JTAG interface
cable to the target board
zAttach the TDS560USB PLUS JTAG Emulator to the host computer
system using a USB cable
zApply power to the TDS560USB PLUS JTAG Emulator
WARNING
Make sure that the interface cables are connected to the correct
orientation. Pin 1 on the interface cable should match Pin 1 on
the DSP system connector. The TDS560USB PLUS JTAG
Emulator features a "keyed" connector to minimize the chance
of error.
Do not force cables into position. Forcing them may either
damage the cables or the interconnected boards and systems.
5

TDS560USB PLUS Emulator Installation Guide
The USB Device Drivers Installation
1. After plug the TDS560USB PLUS JTAG Emulator into the host
computer's USB port and turn on the power, the system should
display the “Found New Hardware” (Figure A-1) dialog box. This
dialog box indicates the computer operating system has found a new
USB device.
Figure A-1
2. The system will prompt for new hardware detected and start the “Found
New Hardware Wizard” as shown in Figure A-2.
Figure A-2
3. Click on “Next” and the system will display the window as shown in
Figure A-3. Check “Search for the best driver in this location” and
Check “include this location in the search”, then Browse the file
“TDS560USB_PLUS.INF “ in the installation CD, or in the folder
6

TDS560USB PLUS Emulator Installation Guide
where you have copied the file into, as shown in Figure A-3.
Figure A-3
4. Click on “Next” and the following window will be displayed, as shown
in Figure A-4.
Figure A-4
7
Inhaltsverzeichnis
Andere Wintech Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken

EMC2
EMC2 VNX Series Betriebsanleitung

Panasonic
Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon
Raidon iT2300 Bedienungsanleitung

National Instruments
National Instruments PXI-8186 Bedienungsanleitung













