Wizard 8000 RC Bedienungsanleitung
Wizard™ CMC Model 8000 RC
Getting Started Guide
FrameShop
FrameShop™
20-71034-1
2
Wizard™ International, Inc., 4600 116th St. SW, Mukilteo, WA 98275 888/855-3335 Fax: 425/551-4350 wizardcutters.com
Wizard™ International, Inc.
4600 116th. Street Southwest
Mukilteo, WA 98275-0066 USA
For information on our products and services or for technical support call Wizard at 1-888-855-3335 or visit us
at www.wizardcutters.com
Copyright © 2000 - 2019, Wizard International, Inc.
This product and its documentation are protected by copyright and are distributed under license restricting its use, copying, distribution
and decompilation. No part of this software product may be copied, reproduced or disassembled without written permission from Wizard
International, Inc. and its licensors, if any.
Trademarks: FrameShop™ is a trademark of Wizard International, Inc.
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-
INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.
CMC 8000RC/FrameShop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
3
Wizard CMC Model 8000 RC Hardware and Software Getting Started Manual
CMC 8000RC/Frameshop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
Wizard CMC 8000 RC
Getting Started Manual
Contents
Check CMC Contents.....................................................................................................5
Equipment Required.................................................................................................5
Where to Find More Information ...................................................................................5
Knowledge Base .......................................................................................................5
Website ......................................................................................................................5
CMC Parts .......................................................................................................................6
Head Labeled.............................................................................................................6
Cartridges ..................................................................................................................6
Driver Pack/ECU and Air Regulator.........................................................................6
The 8000 CMC Parts Labeled...................................................................................7
Setting up the CMC ........................................................................................................8
Setting up the Stand or Wall Mount ........................................................................8
Taking the CMC out of the Box ................................................................................8
Remove Gantry Cover ..............................................................................................9
Removing the Shipping Blocks ...............................................................................9
Check Squareness..................................................................................................10
Head Installation...........................................................................................................10
Install the Head onto the Gantry............................................................................10
Hooking up the Gantry and Air Lines ......................................................................... 11
Connecting the Board Cable.................................................................................. 11
Attaching Air Lines and Air Regulator ..................................................................12
Install Gantry Cover................................................................................................12
Hook up Computer .......................................................................................................13
Hook up Computer Peripherals .............................................................................13
Connect the Driver Pack/ECU................................................................................13
Power up the Driver Pack/ECU ..............................................................................14
4
Wizard™ International, Inc., 4600 116th St. SW, Mukilteo, WA 98275 888/855-3335 Fax: 425/551-4350 wizardcutters.com
CMC 8000RC/FrameShop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
Boot the Computer..................................................................................................14
Design the First Mat .....................................................................................................14
Edit New Mat............................................................................................................14
Go to Cut Preview to Cut the First Mat.......................................................................16
Install a Blade..........................................................................................................17
Put Matboard onto CMC .........................................................................................18
Align the Head When Motors are Disengaged...........................................................19
Align the Head.........................................................................................................19
Insert Blade Cartridge and Adjust Blade Depth ...................................................20
After the CMC Has Cut the Mat..............................................................................20
Design a Dierent Mat..................................................................................................20
Select a Dierent Template ....................................................................................20
Changing the Blade......................................................................................................22
Using the 45° Cartridge ..........................................................................................22
Troubleshooting ...........................................................................................................22
Frequently Asked Questions.......................................................................................23
Hardware Maintenance ................................................................................................24
Maintenance Schedule ...........................................................................................24
Ooad Air Regulator ..............................................................................................24
Disclaimers ...................................................................................................................24
5
Wizard CMC Model 8000 RC Hardware and Software Getting Started Manual
CMC 8000RC/Frameshop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
Wizard CMC Model 8000 RC Hardware and
Software Getting Started Manual
Check CMC Contents
Upon receipt of equipment, review for shipping damage and advise if any. Verify that contents listed on the pack-
ing slip are received. Read Manual before installing and operating equipment. Save Packaging.
Equipment Required
The CMC Stand must be assembled rst before unpacking the Wizard™ CMC (Computerized Mat Cutter)
1/4" female tting on main airline, or quick disconnect attachment
110 volt electrical outlet
Air source - You will need an air compressor that supplies between 100psi and 120psi.
Surge Protector
Table for the Computer/Monitor
Where to Find More Information
Knowledge Base
Login to the Knowledge Base with your Customer ID, which can be found on your License Screen (Options >
View License from the FrameShop main screen).
The Knowledge Bases contains a wide assortment of searchable documentation and information which can
be found at:
FrameShop Software Knowledge Base: http://info.wizardint.com/FS40.
8000 Hardware can be found on the Knowledge Base: http://info.wizardint.com/KB.
Website
Check out the Wizard website at www.wizardcutters.com for additional information.
6
Wizard™ International, Inc., 4600 116th St. SW, Mukilteo, WA 98275 888/855-3335 Fax: 425/551-4350 wizardcutters.com
CMC 8000RC/FrameShop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
CMC Parts
Head Labeled
Cartridges
45° Deboss Deboss Deboss
Thin Medium Wide
Driver Pack/ECU and Air Regulator
Driver Pack ECU Air Regulator
7
Wizard CMC Model 8000 RC Hardware and Software Getting Started Manual
CMC 8000RC/Frameshop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
The 8000 CMC Parts Labeled
A: Belt Anchor
B: Magnetic Stop
C: Bottom cover containing vertical belt tension
adjustment.
D: Head and the blade depth knob
E: Head grabber arm
F: Mat to be cut
G: Vertical clamp
H: Gantry arm
I: Drive shaft
J: Belt anchor
K: Upper cover
L: Upper rail, containing drive belt
M: Backing mat (2 layers)
N: Horizontal tension adjustment (upper rail)
O: Horizontal tension adjustment (lower rail)
P: Horizontal clamp
Q: Lower rail, containing drive belt
8
Wizard™ International, Inc., 4600 116th St. SW, Mukilteo, WA 98275 888/855-3335 Fax: 425/551-4350 wizardcutters.com
CMC 8000RC/FrameShop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
Setting up the CMC
Congratulations on acquiring the Wizard™ computerized mat cutter (CMC). The following instructions will
walk you through unpacking and setting up the CMC.
Begin by clearing an area for the CMC. Refer to the Stand Instructions for the minimum amount of space
needed.
Setting up the Stand or Wall Mount
*CAUTION: The stand MUST be assembled before unpacking
the CMC so it can be immediately installed in the operating
position.*
Assembling the Stand Assembly
Refer to the stand assembly instructions located in the box. If the instructions or any parts are missing, call
Technical Support at (888) 855-3335.
Taking the CMC out of the Box
1. With the help of a second person, place the box carefully on a at surface,
cut the strapping tape and lift the cover of the box away. Take care to save the
packaging.
2. The drive shaft is the thin cylindrical bar on the left that runs the length of the
Gantry. The gantry arm is the thick rectangular housing on the right that runs
the length of the gantry. Only use the gantry arm to move the gantry across the
board.
3. Working together, carefully lift the CMC straight up out of the box. Gently set
the CMC upright resting on the foam corners.
4. Position the CMC on the wall mount or stand, making sure that none of the air
lines are crimped, and that the grounding strap on the rear side of the board is not
crimped between the board and stand arm.
5. Remove foam corners and move the boxy out of the way.
6. Follow the instructions that came with the stand to secure the CMC into place and attach the grounding
strap.
7. Place the foam corners back into the box. Save packaging, foam corners and shipping blocks (removal
instructions below) for future use. See Contract Section 1 “Shipping Charges.”
NEVER SKIP AHEAD ON ANY STEP! Never pull/push on the Drive
Shaft to move the Gantry. Use the Gantry Arm.
9
Wizard CMC Model 8000 RC Hardware and Software Getting Started Manual
CMC 8000RC/Frameshop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
Remove Gantry Cover
1. Remove the screw holding the bottom gantry cover in place, and set the cover
and screw aside aside.
Removing the Shipping Blocks
1. Locate the four shipping blocks holding the gantry in place.
There are two on the upper gantry. One is to the left of the
gantry on the underside of the top rail,
and one is to the right of the gantry on the top of the rail.
There are two shipping blocks on the lower gantry on
either side of the gantry on top of the the bottom rail.
2. Remove the shipping blocks by loosening
the 3/16” Allen screw from the T-Nut. Slide
the T-Nuts to the right end of the rail; a pencil
tip helps. Reattach the T-Nuts to the shipping
blocks and place them in the shipping box for
storage.
10
Wizard™ International, Inc., 4600 116th St. SW, Mukilteo, WA 98275 888/855-3335 Fax: 425/551-4350 wizardcutters.com
CMC 8000RC/FrameShop 20-71034-1 GettingStartedManual8000RCFrameShop
http://info.wizardint.com/KB/default.aspx#pageid=getting_started_manual_8000_rc 04/05/19
Check Squareness
Check the Drive Belt Lines
1. Move the gantry all the way to the left. Move the gantry slowly
toward the right until a red mark is visible on the drive belt of the
upper gantry. Conrm that the red mark lines up with the red mark
on the drive pulley.
Without moving the gantry, look at the lower drive belt of the
gantry and make sure the red mark lines up on the lower drive
belt and the drive pulley. If they do not, call the Help Desk.
Head Installation
Install the Head onto the Gantry
Do not pick up the Head using the Blade Depth
Knob.
1. Remove the two 5/32" screws from the head and set aside.
2. Move the gantry to the right edge of the CMC.
3. Point the head so that the foot block faces toward the CMC and the wheels are
close to the bottom of the gantry.
4. Line up the wheels on the head to the center channels of
the Gantry arm. Ease the Head onto the gantry arm and ease
the head onto the gantry.
5. Roll the head up on the gantry until it lines up to the head grabber arm
(attached to the right side of the gantry).
Inhaltsverzeichnis
Andere Wizard Cutter Handbücher
Beliebte Cutter Handbücher anderer Marken
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung
Makita
Makita DCS552 Bedienungsanleitung
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Bedienungsanleitung
Makita
Makita 4112HS Bedienungsanleitung
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Bedienungsanleitung
Hitachi
Hitachi CM 4SB2 Fehlerbehebungshandbuch
