Wolf Drawer Microwave Oven Bedienungsanleitung

Cooktop Ventilation Hoods Installation Guide

COOKTOP VENTILATION HOODS

Contents

3Cooktop Ventilation Hoods

4Specications

6Installation

10 Troubleshooting

Features and specications are subject to change at any

time without notice. Visit wolfappliance.com/specs for the

most up-to-date information.

Wolf Customer Care 800.222.7820

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

wolfappliance.com

Product Information

Important product information including the model and

serial number are listed on the product rating plate. The

rating plate is located under the left side of the hood, above

the lters (lters must be removed). Refer to the illustration

below.

If service is necessary, contact Wolf factory certied ser-

vice with the model and serial number. For the name of

the nearest Wolf factory certied service or for questions

regarding the installation, visit the contact & support section

of our website, wolfappliance.com or call Wolf customer

care at 800-222-7820.

COOKTOP VENTILATION HOODS

RATING PLATE

Rating plate location.

Wolf Customer Care 800.222.7820

Electrical

Installation must be electrically grounded in accordance

with local codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70.

For wall hoods, locate the electrical supply within the

shaded area shown in the illustration below. Allow a

minimum 12" (305) Romex®wire for connection. For island

hoods, locate the electrical supply on the ceiling inside the

top of the hood. Allow a minimum 6' (1.8 m) Romex®wire for

connection. A separate circuit, servicing only this appliance

is required.

ELECTRICAL REQUIREMENTS

Electrical Supply grounded, 110/120 VAC, 60 Hz

Service 15 amp dedicated circuit

SPECIFICATIONS

Installation Requirements

Wolf cooktop ventilation hoods are recommended for use

with Wolf induction, electric and gas cooktops and inte-

grated modules. For ranges and rangetops, a Wolf pro venti-

lation hood is recommended.

These hoods have a telescopic chimney ue. A ue exten-

sion is available through an authorized Wolf dealer.

Installation of the cooktop hood should be 30" (762) to

36" (914) from the bottom of the hood to the countertop.

Wall and island hoods require an internal, in-line or remote

blower assembly, available through an authorized Wolf

dealer. For local dealer information, visit the nd a show-

room section of our website, wolfappliance.com.

Consult a qualied HVAC professional for specic installa-

tion and ducting applications.

18"

(457)

30"

(762) TO 36" (914) BOTTOM EDGE TO COUNTERTOP

LOCATE

ELECTRICAL

WITHIN

SHADED AREA

Electrical location—all wall hoods.

wolfappliance.com

SPECIFICATIONS

Ductwork

WARNING

To reduce the risk of re, use only metal ductwork.

6" (152) round, rigid metal duct is recommended for cooktop

ventilation hoods.

A straight, short run is most effective and will ensure proper

operation. For best results, the duct run should not exceed

50' (15 m). For runs exceeding 50' (15 m), a higher CFM

blower may be required to maintain proper air ow and

performance. A remote blower installed on a short duct run

may increase the potential for noise.

Internal and in-line blowers require a roof or wall cap (not

provided). Connect ductwork to the cap and work back

towards the hood. Use sheet metal screws and aluminum

tape or high temperature duct tape to seal joints between

ductwork sections.

Wall and island hoods include a backdraft damper. Local

codes may require the use of an additional backdraft and/or

make-up air damper. Contact your local HVAC professional

for specic requirements.

A make-up air damper is available through an authorized

Wolf dealer. For local dealer information, visit the nd a

showroom section of our website, wolfappliance.com.

Wolf Customer Care 800.222.7820

INSTALLATION

2Place the mounting tabs over the mounting screws. Use

the leveling adjustment screws to ensure the hood is

level. Refer to the illustration below.

3Mount the electrical plate to the wall using screws

provided.

4Place the backdraft damper on the round discharge then

install 6" (152) round metal ducting (not provided) to the

damper and seal with aluminum tape.

5Make wiring connections. Refer to page 9.

6Once wiring connections are complete, secure the upper

chimney ue to the mounting brackets using screws

provided. Refer to the illustration below. Place the lower

chimney ue over the upper, then lower until it rests on

the hood.

Installation

WALL HOOD

If an internal blower is being installed, install the blower prior

to mounting the hood. Refer to page 8 for internal blower

installation.

1Mark the center line for location of two mounting holes

using dimensions shown in the chart and illustration

below. Additional wall framing is recommended in this

location. If wall framing is not available, the use of wall

anchors is recommended. Install the mounting screws

so there is approximately 1/4"(6) gap between the screw

head and wall. Position the two mounting brackets for

the chimney ue, then install using two mounting screws

per bracket. Refer to the illustration below.

MOUNTING LOCATION

SCREW LOCATION A

Black Hood 123/4"(324)

Stainless Hood 163/8"(416)

Glass Hood 129/16"(319)

BOTTOM OF HOOD

CEILING

91/8"

(232)

171/16"

(433)

3/4"

(19)

Mounting location.

MOUNTING

TA B

LEVELING

SCREW

Mount and level hood.

Install telescopic ue.

wolfappliance.com

INSTALLATION

wolfappliance.com

4Place the damper on the support frame then attach duc-

twork to the damper.

5Slide the upper chimney ue onto the support frame and

attach to the support frame using screws provided. Refer

to the illustration below. Slide the lower chimney ue

over the upper and temporarily secure in this position

using adhesive tape.

6Raise the hood to the support frame and connect the

hood to the support frame with four screws provided.

Refer to the illustration below.

7Make wiring connections. Refer to page 9.

8Once wiring connections are complete, remove the

adhesive tape securing the lower chimney ue, then

lower until it rests on the hood.

Installation

ISLAND HOOD

If an internal blower is being installed, install the blower prior

to mounting the hood. Refer to page 8 for internal blower

installation.

1Mark the center line for location of four mounting holes

using dimensions shown in the illustration below. Use

the template provided to mark the mounting support

locations, then use a 11/4" drill bit to create a hole for the

electrical power supply.

2Place four mounting screws into the ceiling, then posi-

tion the support frame on those screws. Once the sup-

port frame is in place, tighten screws.

3Determine the desired height of the support frame and

adjust the height by removing four screws. Once the

desired height is achieved, reinstall and tighen screws.

85/8"

(219)

ELECTRICAL

LOCATION

11"

(279)

Mounting location.

Support frame.

MOUNTING

SCREW

UPPER

FLUE

MOUNTING

SCREW

Install telescopic ue.

Mount hood.

Wolf Customer Care 800.222.7820

Installation

INTERNAL BLOWER

If an internal blower will be used, it should be installed prior

to mounting the hood. Refer to additional instructions pro-

vided with the internal blower.

1Insert the three-prong plug from the blower wire into the

hood receptacle. Refer to the illustration below.

2Insert the blower by aligning the round discharge on the

blower with the discharge on the hood.

3Insert the plug from the blower wire into the receptacle

on the blower. Refer to the illustration below.

4Secure the blower to the hood using the two mounting

screws provided.

INSTALLATION

RECEPTACLE RECEPTACLE

MOUNTING

SCREW

Hood receptacle.

Mount blower.

wolfappliance.com

Wiring Connections

INTERNAL BLOWER WIRING

1Remove the top cover of the electrical box by extracting

two screws. Refer to the illustration below.

2Remove the two existing wires from the left side of

the terminal block and transition them to the right and

secure. Refer to the illustration below.

3Place all wiring connections inside the electrical box and

reinstall the cover. Make sure all wires are secure and not

pinched between the cover and electrical box.

4Secure the junction box supplied with the hood to the

wall, then connect to the (Romex®) power supply from

the home. Once the connection has been made, insert

the plug into the receptacle on the hood.

MOVE WIRES

HERE

COVER

BLUE

BROWN

BLUE

BROWN

TO INTERNAL

BLOWER

BLUE

BROWN

Wiring location.

Internal blower wiring.

INSTALLATION

IN-LINE / REMOTE BLOWER WIRING

1Remove the top cover of the electrical box by extracting

two screws. Refer to the illustration below.

2Remove one of the round knockouts using a at blade

screwdriver.

3Insert Romex®wire from the blower through the

knockout and secure using an approved cord stain relief.

4Connect white to blue, black to brown and green to

ground. Refer to the illustration below.

5Place all wiring connections inside the electrical box and

reinstall the cover. Make sure all wires are secure and not

pinched between the cover and electrical box.

6Secure the junction box supplied with the hood to the

support frame, then connect to the (Romex®) power

supply from the home. Once the connection has been

made, insert the plug into the receptacle on the hood.

KNOCKOUT

COVER

WHITE

BLACK

GREEN

GROUND

BLUE

BROWN

TO IN-LINE/REMOTE

BLOWER

BLUE

BROWN

Wiring location.

In-line / remote blower wiring.

Wolf Customer Care 800.222.7820

Troubleshooting

IMPORTANT NOTE: If the ventilation hood does not operate

properly, follow these troubleshooting steps:

•Verify electrical power is supplied to the ventilation hood.

•Verify proper wiring connections.

•If the ventilation hood does not operate properly, contact

Wolf factory certied service. Do not attempt to repair

the hood. Wolf is not responsible for service required to

correct a faulty installation.

TROUBLESHOOTING

Andere Handbücher für Drawer Microwave Oven

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wolf Dunstabzugshaube Handbücher

Wolf

Wolf PW662718 Gebrauchsanweisung

Wolf

Wolf Pro Wall Series Bedienungsanleitung

Wolf

Wolf CTWH30 Bedienungsanleitung

Wolf

Wolf PW362210 Gebrauchsanweisung

Wolf

Wolf VC48W Bedienungsanleitung

Wolf

Wolf PW302418 Bedienungsanleitung

Wolf

Wolf PW482210R Betriebsanleitung

Wolf

Wolf CTWH36 Bedienungsanleitung

Wolf

Wolf PL342212 Bedienungsanleitung

Wolf

Wolf PL582212 Bedienungsanleitung

Wolf

Wolf L582212 Gebrauchsanweisung

Wolf

Wolf Downdraft Ventilation Betriebsanleitung

Wolf

Wolf PW422718 Gebrauchsanweisung

Wolf

Wolf PWC362418 Gebrauchsanweisung

Wolf

Wolf CTWH30 Betriebsanleitung

Wolf

Wolf 42" Bedienungsanleitung

Wolf

Wolf Ventilation Hood Bedienungsanleitung

Wolf

Wolf PI663418 Gebrauchsanweisung

Wolf

Wolf DD45I Bedienungsanleitung

Wolf

Wolf Drawer Microwave Oven Bedienungsanleitung

Wolf

Wolf Downdraft Ventilation Bedienungsanleitung

Wolf

Wolf PL342212 Gebrauchsanweisung

Wolf

Wolf PI543418 Gebrauchsanweisung

Wolf

Wolf CTWH30 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

Küppersbusch

Küppersbusch DX ISLA Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung