Woodbridge B0090 Montageanleitung

WOODBRIDGE

www.woodbridgebath.com

READALLINSTRUCTIONSBEFOREUNPACKINGTHEPRODUCT

2PEOPLEAREREQUIREDTO LIFT AND DURING

ENTIREINSTALLATIONOFTHISPRODUCT

INSTRUCTIONSTHAT,IF IGNOREDCOULD RESULTIN DEATH ORSERIOUS INJURYCAUSEDBY INCORRECTHANDLING

ORINSTALLATION OFTHEPRODUCT. THESEINSTRUCTIONSMUST BEOBSERVED FORSAFE INSTALLATION.

This products must be installed by a fully insured and licensed plumber only. Installaon of any our product by anyone other

than fully insured and licensed plumber shall void limited warranty. We recommends that such licensed plumber has experience

in the installaon of products.

Limited warranty is void on any commercial installaon

We are not responsible for local code compliance for this product. Building and plumbing codes may vary from state-to-state in

accordance to your locaon. We are not responsible for providing any compliance cerﬁcaons.

Under no circumstances we shall not be liable for any incidental damages sustained in connecon with this product

Neither manufacture, nor distributor, nor retailer is responsible for water damage or ﬂood caused due to use of this product.

Under no circumstances We shall not be liable for any and all fees, cost of installaon/reinstallaon/removal, subsequent

damage or transportaon in case of the product defect

WOODBRIDGE

INSTALLATION AND CARE GUIDE

Customer Service Phone: 562-229-0088. (Monday - Friday 9 AM - 5 PM Paciﬁc Time)

Or Email: [email protected]

20200922 REV. 5

CertifiedtothefollowingCodes&Standard:

•U.S Safety Standard:UL1795– Hydromassage Bathtubs (UL)

• ASMEA112.19.7 /CSAB45.10-2012(R17)–HydromassageBathtub Systems

•CSA B45.5/IAPMOZ124-2017–PlasticPlumbing Fixtures

•2009 and2006InternationalPlumbingCode®(IPC)

•2021, and2006InternationalResidentialCode®(IRC)

•2018, 2015, and2006UniformPlumbingCode®(UPC)

Whirlpool & Air Bubble Bathtub

Two persons Hot Tub

B0090/BTS0090 B0091/BTS0091 B0092/BTS0092

WOODBRIDGE

www.woodbridgebath.com

BEFORE YOU BEGIN

PRODUCT REQUIREMENTS

A. Summary Of Key Requirements

Observe all local plumbing codes, Install the unit to a level subﬂoor,Provide properly

-dimensioned framing.

B. Product Inspection

Uncrate and inspect bath for damage. Leave all materials in the crate during construcon to

prevent damage.

ROUGHING-IN

• All informaon is based on the latest product informaon available at the me of

publicaon. WOODBRIDGE® reserves the right to make changes in product

characteriscs, packaging, or availability at any me without noce.

• Please read these instrucons carefully to familiarize yourself with the required

tools, materials, and installaon sequences. Follow the secons that pertain to your

parcular installaon. This will help you avoid costly mistakes. In addion to proper

installaon, read all operang and safety instrucons.

IMPORTANT INFORMATION

• Measurements are ± 1/2" and subject to change without noce

• Speciﬁcaons & Conﬁguraons are subject to change without noce

• Please measure tub on-site before installaon

• Please note that installer(s) must be cerﬁed or warranty will be voided.

• Measurements herein supersede all others published prior to purblicaon

date shown below

• Before ordering or installing, please consider future access to equipment

B0091/BTS0091

Control box

15"

Water depth

47 1/4"

35 3/8"

45 5/8"

70 7/8"

23 5/8"

27 1/2"

Air Blower

(0.3KW)

B0092/BTS0092

26 3/4"

23 5/8"

31 1/2"

20"

41 3/4"

67"

15"

Water depth

Control box

47 1/4"

37 3/4"

45 5/8"

70 7/8"

26 3/8"

23 5/8"

14 7/8"

Water depth

Heater

(1.5KW)

Hydromassage

Pump (1.1KW)

Air Blower

(0.3KW)

Control box

6 5/8"

B0090/BTS0090

Hydromassage

Pump (1.1KW)

Heater

(1.5KW)

Air Blower

(0.3KW)

Hydromassage

Pump (0.75KW)

Heater

(1.5KW)

WOODBRIDGE

www.woodbridgebath.com

INSTALL BATHTUB

1) Your new bathtub has been manufactured to the highest possible standards,it has been tested

and approved by factory

INSTALLATION REQUIREMENTS

A. Tools Required

• Adjustable pipe

• wrench

• Ruler

• Level

• Safety shoes

• Safety glasses

• Square

• Screwdriver

• Pliers

• Ulity knife

B. Materials Required:

• Plumbers puy

• Wall coverings, as necessary

• Silicone sealant

• Gypsum cement (oponal)

• Construcon adhesive

• (oponal)

• Protecve covering for

• bathtub

• Nails

C. Clearance Requirements:

Check the rough-in and room dimensions to provide adequate space for the bath unit.

SITE REQUIREMENTS

A. Plumbing Preparation

Posion the plumbing according to rough-in dimensions.

Cap the supplies and check for leaks.

BEFORE INSTALLING UNIT

CAUTION: Ensure a watertight seal on the bath drain connections.

A. Install the faucet valving and shower head tee.When drilling bathtub for faucet,

ensure suﬃcient clearance. Open the hot and cold water valves and check the

supply connecons for leaks.

B. Run water into the bath and check the drain connecons for leaks.

C. Fill the bathtub up to the overﬂow level and check overﬂow unit for leaks.

This products must be installed by a fully insured and licensed plumber only.

2) When removing bathtub from protecve carton. DO NOT LIFT BATHTUB BY PIPE WORK.

Inspect for any possible damage that may have occurred in transit.

IMPORTANT: Bathtub must be installed level on all top edges..

WOODBRIDGE

www.woodbridgebath.com

4) Connect Power Supply:

Connect power supply to control unit. The electrical connecons must comply with local

authority regulaons and must be done by an authorized electrician.

5) Fill bathtub with water to approximately 40mm(1.6˝) above the jets and trial run pump for

10-15 minutes. Check all the ﬁngs for leaks and test the control funcons. Switch oﬀthe

spa pump and leave the unit ﬁlled with water (pump is not running) for at least another two

minutes. Check the pump and pipes union connecons for leaks. Hand ghten union

connecons if required.

IMPORTANT: Your bathtub has been factory tested and approved. It is the responsibility of

the installer to test run the bathtub, check all the ﬁngs for leaks and test the control funcons.

NON OBSERVANCE WILL INVALIDATE FACTORY WARRANTY.

6) The unit must be connected only to a supply circuit that is protected by a Ground-Fault

Circuit Interrupter (GFCI). Such a GFCI should be provided by the installer and should be

tested on a roune basis.

ELECTRICAL REQUIREMENTS

WOODBRIDGE

120V 30AMP

Dedicated

GFCI Breaker

3) Set the bathtub on two 4x4 pieces of lumber .so you can access from the boom of the bathtub.

GROUND

NEUTRAL

THE LEAKAGE SWITCH

CONTROL BOX

NEUTRAL GROUND

Whirlpool & Air Bubble Bathtub

Two persons Hot Tub

Whirlpool & Air Bubble Bathtub

Two persons Hot Tub

On above example, there is a 120V 30AMP Dedicated GFCI Breaker

WOODBRIDGE

www.woodbridgebath.com 5

Failure

Faults

Big noise of

generator

Plumbing

leakage

Fault Cause

Voltage instability

The plug drops oﬀor short circuit

Pneumac switch's failure

The link between pneumac switch

and the pipe drops oﬀor breaks

Aging of sealing ring

Bad connecon

Plumbing leakage

Soluon

Check the voltage

Plug the power or replace it

Change the switch

Check it with the distributor

Ajust it / ghten it

Adjust it to be level

Reconnect

1.Voltage/HZ needs match up with the product's parameter.

2.Power supply needs a good grounding.

3.The pressure of water supply needs meet 0.2-0.4Mpa.

4.The Whirlpool funcon will funcon when the level of water

injecon is higher than the level of jets.

5.Turn oﬀthe power before draining.

Voltage/Hz Power Current

110V/60HZ 2.8KW >23A

TROUBLE SHOOTING

Reconnect it or replace the pipe

The voltage not match with

the data on the name plate

Screws from generator is loosen or

dropped oﬀ

The tub feet are not level

Replace with a new sealing ring

Replace the plumbing parts

WOODBRIDGE

www.woodbridgebath.com 6

Hot and cold water regulang switch

Funcon switch valve

Eﬄuent

Shower

Cold water pipe(1.5m)

Hot water pipe(1.5m)

Hot Cold

GROUND

NEUTRAL

THE LEAKAGE SWITCH

NEUTRAL GROUND

The control panel

Force regulang valve

Display window

Switch conﬁrmaon key

Funcon selecon key

Instrucons

Control box

OODBRIDGE

WOODB

OODBRIDGE

WOODB

OODBRIDGE

WOODB

www.woodbridgebath.com 7

Service Access Door

Tub Rim

Service Access Door

LED light indicator

WOODBRIDGE

www.woodbridgebath.com

DANGER Sign: RISK OF SEVERE INJURY FROM ELECTRIC SHOCK OR DEATH

FROM ELECTROCUTION!

CAUTION Sign: IMPORTANT INSTALLATION GUIDE AND MAINTENANCE TIPS

TO BE FOLLOW PER MANUFACTURE.

WARNING:

1. In order to prevent ﬁre or electrical shock, DO NOT expose the control box on rain or wet environment.

Control box contains dangerous high voltage parts and DO NOT open the control box. This product to

be service by cerﬁed technician only.

2. Any modiﬁcaon or seng to the controller without authorizaon or conﬁrmaion from manufacture or

its dealer might cause mal funconto the product.

CAUTION:

1. Follow the instrucons on this manual to operate.

2. Please keep this installaon manual for future reference aer installaon. Please contact your local

authorize dealer or call our customer service support for any assistance with operaon or maintenance

-related queson.

OPERATION TIPS:

1. Unplug the socket from electric outlet if the product will not be used in a period.

2. Make sure the wiring and connecon are well connected per manufacture before turning on the unit.

3. Place this controller on dry and venlaon area, cleared from heat, sunshine, mechanical vibraon,

moisture, dust and any radiaon object.

DO:

1. Take at least 30 seconds ON and OFF from last operate, this will extend the unit life cycle.

2. Power oﬀthe unit aer every use.

3. Follow the voltage and electrical speciﬁcaon guide from manufacture to prevent any mal funcon or

damage to the unit.

4. Follow installaon instrucon per manufacture to prevent any mal funcon or damage to the unit.

5. Turn ON the unit again if accidentally shut down.

WOODBRIDGE

www.woodbridgebath.com 9

CONTROLLER USER MANUAL:

1. Feature descripon:

• Wave Feature

• Air Blower

• Constant Heated

• Temperature Sensor

• Water level detecon

• Child Keypad Lock

• Touch Sensor technology

2. Control system:

• Keypad (x1)

• Control Box (x1)

3. Control Box Speciﬁcaon:

• Voltage: AC110V

• Hertz: 60 Hz

• Consume Voltage: <25A

• Standby Rate: <1W

• Working Temperature: 5C – 40C (41F – 104F)

4. Funcon Control Speciﬁcaon:

• Wave Mode: AC110/1.5HP

• Air Blower Mode: AC110V/400W

• Heated: AC110V/2000W

WOODBRIDGE

www.woodbridgebath.com 10

CONTROL PANEL OPERATION:

(1) Always a BEEP sound on every keypad funcon.

(2) Power ON and OFF

Press and hold Power/Funcon buon for 3 seconds to power on the unit.

Unit with Temperature sensor funcon with display current temperature on LCD screen.

Display will blink if it is not equipped with.

Press and hold Power/Funcon buon for 3 seconds to power oﬀthe unit.

(3) CHILD Keypad Lock

The unit is On and no acvity on the keypad was made, Child keypad lock feature will acvated

and the screen will display a LOCK image and you will be unable to access the menu ll

hold pressing any buon for 3 seconds or more to deacvate it.

LED

Display

Funconal

Key

Power/Funcon

ON/OFF

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Woodbridge Badewanne Handbücher

Woodbridge

Woodbridge WB1028 Montageanleitung

Woodbridge

Woodbridge FREESTANDING BATHTUB Montageanleitung

Woodbridge

Woodbridge B0170 Montageanleitung

Woodbridge

Woodbridge BA5430R Montageanleitung

Woodbridge

Woodbridge BJ200 Montageanleitung

Woodbridge

Woodbridge BTS1606-B0030 Bedienungsanleitung

Woodbridge

Woodbridge BJ500 Montageanleitung

Woodbridge

Woodbridge B0030 Montageanleitung

Woodbridge

Woodbridge BM400 Montageanleitung

Woodbridge

Woodbridge B0030/BTS1606 Montageanleitung

Woodbridge

Woodbridge BM500 Montageanleitung

Woodbridge

Woodbridge Megabrand Bedienungsanleitung

Woodbridge

Woodbridge BS5430R Montageanleitung

Woodbridge

Woodbridge WIC54-01 Bedienungsanleitung

Woodbridge

Woodbridge BTA1531R Montageanleitung

Woodbridge

Woodbridge B0034 Montageanleitung

Woodbridge

Woodbridge BJ600 Montageanleitung

Woodbridge

Woodbridge BJ100 Montageanleitung

Woodbridge

Woodbridge BS0260 Montageanleitung

Beliebte Badewanne Handbücher anderer Marken

Agua

Agua BARTOLI-66 Bedienungsanleitung

PAA

PAA PRELUDE Bedienungsanleitung

BETTE

BETTE SILHOUETTE Bedienungsanleitung

Kohler

Kohler K-820-GC Kurzanleitung

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Bedienungsanleitung

Oliveri

Oliveri Naples Bedienungsanleitung

Lyons

Lyons Elite ETLxx663219 Series Bedienungsanleitung

Whirlpool

Whirlpool Ariel ARL-702 Bedienungsanleitung

TEIKO

TEIKO EXCELLENT DUO Bedienungsanleitung

American Standard

American Standard 3052OD.X0X Kurzanleitung

Kohler

Kohler K-1111-H2 Kurzanleitung

agape

agape MARSIGLIA AVAS1075 Bedienungsanleitung

Kohler

Kohler K-1151 Montageanleitung

Kohler

Kohler K-1158 Kurzanleitung

Kohler

Kohler K-1244 Montageanleitung

Kallista

Kallista P50045-G5 Montageanleitung

Kohler

Kohler K-1164-HB Kurzanleitung

Kohler

Kohler Hourglass K-1209-LA Kurzanleitung