Woodmizer D10 Leitfaden

D10 Engine

Safety, Operation, Maintenance

& Parts Manual

034630 Engine,10HP Yanmar rev A-D

Safety is our #1 concern! Read and understand

all safety information and instructions before oper-

ating, setting up or maintaining this machine.

April 2010

Form #1098

Used with LT15D10 rev. E1.00 - E8.13

Active Patents assigned to Wood-Mizer, LLC

Wood-Mizer, LLC has received patents that protect our inventions which are a result of a dedication to

research, innovation, development, and design. Learn more at: woodmizer.com/patents

any photographic, electronic, mechanical or other means or used in any information storage and retrieval system with-

out written permission from

Wood-Mizer, LLC

8180 West 10th Street

Indianapolis, Indiana 46214

California

Proposition 65 Warning

WARNING:

Breathing gas/diesel engine exhaust exposes you to chemicals known to

the State of California to cause cancer and birth defects or other reproductive harm.

Always start and operate the engine in a well-ventilated area.

If in an enclosed area, vent the exhaust to the outside.

Do not modify or tamper with the exhaust system.

Do not idle the engine except as necessary.

For more information go to www.P65warnings.ca.gov.

WARNING:

Drilling, sawing, sanding or machining wood products can expose you to

wood dust, a substance known to the State of California to cause cancer. Avoid inhaling

wood dust or use a dust mask or other safeguards for personal protection.

For more information go to www.P65Warnings.ca.gov/wood.

Table of Contents Section-Page

Table of Contents WMdoc021822 iii

TOC

SECTION 1 ABOUT THIS MANUAL 1-1

SECTION 2 OPERATION 2-1

2.1 Starting The Engine................................................................................2-1

SECTION 3 MAINTENANCE 3-1

3.1 Safety......................................................................................................3-1

3.2 Cooling System ......................................................................................3-1

3.3 Air Filter & Pre-Cleaner.........................................................................3-1

3.4 Fuel Filter ...............................................................................................3-2

3.5 RPM Adjustments ..................................................................................3-2

SECTION 4 REPLACEMENT PARTS 4-1

4.1 Engine Assembly....................................................................................4-1

LT15 Rev. E1.00+

4.2 Throttle/Clutch Assembly ......................................................................4-3

INDEX I

1-1 WM doc 2/18/22

SECTION 1 ABOUT THIS MANUAL

This manual is provided as a supplement to the equipment manufacturer’s manuals.

This manual provides information specific to the use of this equipment on the Wood-Mizer® sawmill. Refer to the sawmill oper-

ator’s manual and manufacturer's manual before attempting to operate this equipment.

IMPORTANT! Read the sawmill operator’s manual and engine manufacturer’s man-

ual for instructions and safety precautions before operating this equipment.

The information and instructions given in this manual do not amend or extend the limited warranties for the equipment given at

the time of purchase.

Operation

Starting The Engine 2

Operation WM doc 2/18/22 2-1

SECTION 2 OPERATION

2.1 Starting The Engine

DANGER! Ensure the blade is disengaged and all persons are out of the path of the

blade before starting. Failure to do so will result in death or serious injury.

DANGER! Operate your engine only in well ventilated areas. The exhaust gases of

your engine can cause nausea, delirium, and potentially death unless adequate venti-

lation is present.

DANGER! Never operate an engine with a fuel or oil leak. This is a fire hazard, which

may cause serious injury or death.

WARNING! Do not operate engine without proper and operational spark arrester/muf-

fler. Sparks emitted from the engine exhaust could ignite surrounding materials, caus-

ing serious injury or death.

1. See the engine manufacturer’s manual for lubricating oil recommendations.

2. Use #2 or better quality diesel fuel for above freezing starting. Use a #1 quality diesel fuel for below freezing starting.

3. Turn the key switch to the on (#1) position.

4. Push the black thumb knob down and hold.

5. Turn the key switch to the start (#2) position and release.

6. Release the black thumb knob.

ENGINE SHUTOFF

Turn the key switch to the off (#0) position.

Push the black thumb knob up and hold until the engine is shut off.

Maintenance

Safety

3-1 WM doc 2/18/22 Maintenance

SECTION 3 MAINTENANCE

Refer to the manufacturer’s manual for maintenance intervals and procedures unless otherwise instructed in this manual. Fol-

low the manufacturer’s recommendations for dusty conditions.

NOTICE This manual only provides information about additional procedures

or procedures to be performed at different time intervals than found in the

manufacturer's manuals. Refer to the manufacturer's manual for complete

maintenance instructions.

WARNING! Clean sawdust from all guards, vents, control boxes, or any

area where sawdust may gather after every shift. Failure to do so may

result in fire, causing death or serious injury.

3.1 Safety

Use caution when performing maintenance or service to the engine.

DANGER! Take proper protective measures against rotating shafts, pulleys,

fans, etc.

Ensure loose clothing or long hair does not engage rotating members.

DANGER! Do not touch or perform service functions on a hot engine. Allow

the engine to cool sufficiently before beginning any service function. Hot

engine components will cause serious burns.

WARNING! Remove the blade before performing any engine service.

WARNING! Wear eye, hand, and foot protection equipment when performing

service functions.

3.2 Cooling System

Wash the engine or brush off sawdust and debris every 50 hours of operation.

Clean the grass screen, cooling fins, and external surfaces.

Remove any dust, dirt, or oil.

See engine manual for further instructions.

3.3 Air Filter & Pre-Cleaner

WARNING! Always wear proper and necessary safety equipment when per-

forming service functions. Proper safety equipment includes eye protection,

breathing protection, hand protection and foot protection.

Service the pre-cleaner every four hours of operation by gently shaking excess sawdust and debris from the foam piece.

Clean the air filter (air cleaner element) and pre-cleaner (element wrapper) every eight hours of operation.

Replace the air filter (cleaner) every 200 hours of operation.

Maintenance

Fuel Filter 3

Maintenance WM doc 2/18/22 3-2

Replace the pre-cleaner (element wrapper) every 2000 hours of operation.

See the engine manual for further instructions.

3.4 Fuel Filter

Replace the fuel filter every 100 hours of operation or as required for engine performance.

3.5 RPM Adjustments

WARNING! Remove the blade before performing any engine service. Failure

to do so may result in serious injury.

Check the RPM with a tachometer every 200 hours of operation.

Before checking the RPM, make sure belt and brake strap tensions are correct (See Sawmill Maintenance).

Check oil, fuel, and coolant levels.

Ensure the throttle cable does not affect the engine RPM when the clutch handle is disengaged. Ensure the cable is not bent or

kinked.

Engine High End RPM Low End RPM

D10 3600 1000

Replacement Parts

Engine Assembly

4-1 WM doc 2/18/22 Replacement Parts

SECTION 4 REPLACEMENT PARTS

4.1 Engine Assembly

LT15 Rev. E1.00+

REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.

Cover, Engine P12393 1

ENGINE ASSEMBLY, 10 HP YANMAR W/CLUTCH 034630 1

1Engine, D10 Yanmar 034839 1

Filter, D10 Yanmar Engine Air (Engine Type LR100B6 2005+) 054916 1

Filter, D10 Yanmar Engine Air (Engine Type LE100EED15) 034028 1

Filter, D10 Yanmar Engine Oil 034029 1

Filter, D10 Yanmar Engine Fuel #114650-55120 046962 1

Nozzle, D10 Yanmar Engine Injector 034030 1

Injector, D10 Yanmar Engine 034031 1

150102C

19 20

Replacement Parts

Engine Assembly 4

Replacement Parts WM doc 2/18/22 4-2

Starter, D10 Yanmar Engine 034032 1

Throttle and Clutch Parts (See Section 4.5)

Hose, Oil Drain P10082 1

Cap, Oil Drain Hose P04332 1

2Plate, LT15 Engine Guard 016493 1

3Sheave, BK55QT 016512 1

4Key, 1/4” X 1 11/16” S04124 1 1

5Bushing, QT X 1 016513 1

6 BELT, BX87 DRIVE 017943 1

7 NUT, 3/8-16 HEX NYLON LOCK F05010-10 4

8 WASHER, 3/8” FLAT SAE F05011-3 4

9 BOLT, 3/8-16 X 119 HEX HEAD F05007-119 4

Harness Assembly, Battery To Engine 024718 1

Battery Box module, LT15D/G 034609 1

10 Mount Weldment, Battery/Control Box 034899 1

11 Bolt, 1/4-20 x 3/4 Hex Head w/Conical Washer F05005-134 4

12 Nut, 1/4-20 Nylon Lock F05010-69 4

13 Battery, 12V 524/26A 028004 1

14 Clamp, Negative Battery 033359 1

15 Clamp, Positive Battery 033358 1

16 Box, Battery 016413 1

17 Decal, 12V Warning P10364 1

18 Bolt, 3/8-16 x 1 HHC F05007-7 3

19 Washer, 3/8 Split Lock F05011-4 3

20 Washer, 3/8 Flat SAE F05011-3 3

21 Washer, Felt Battery Terminal P12161 1

22 BOLT, M8 Z 125 X 16MM HEX HEAD F05004-47 2

23 WASHER, 5/16 SAE FLAT F05011-17 2

24 WASHER, 5/16” SPLIT LOCK F05011-13 2

1 Replaces S21486 1/4” x 1” key (S04124 always used in production).

REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.

Replacement Parts

Throttle/Clutch Assembly

4-3 WM doc 2/18/22 Replacement Parts

4.2 Throttle/Clutch Assembly

REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.

1 PLATE, KEY SWITCH MOUNT 034813 1

2 SHUT-OFF WELDMENT, THROTTLE LT15D 034808 1

3 BOLT, M6-1.0 X 40MM HEX HEAD F81001-5 1

4 NUT, M6-1.0 FREE NUT F81031-1 1

5 SPRING, EXTENSION 3/8 X 3 014818 1

6 BOLT, 1/4-20 X 1 HEX HEAD GR5 F05005-101 1

7 NUT, 1/4-20 KEPS F05010-9 1

8 CABLE ASSEMBLY, LT15D10 THROTTLE 034809 1

9 KNOB, 5/8-11 BALL P04211 1

10 HANDLE, LT15 CLUTCH 016487 1 1

11 SCREW, 3/8-16 X 3/8SOCKET HEAD CUP PT SET F05007-68 2

12 ACTUATOR WELDMENT, THROTTLE LT15D&G 034815 1

13 LINKAGE, THROTTLE LT15D&G 034818 1

14 BOLT, 1/4-20 X 1/2 HEX HEAD F05005-15 1

15 NUT, 1/4-20 SWAGED F05010-21 1

16 BUSHING, 5/8 ID X 7/8 OD X 1 1/8 LONG FL BRONZE 016486 3

150101F

17 18

28 29

Andere Handbücher für D10

Inhaltsverzeichnis

Andere woodmizer Motor Handbücher

Beliebte Motor Handbücher anderer Marken

Rotax

Rotax 125 senior MAX evo Bedienungsanleitung

Kohler

Kohler K361 Bedienungsanleitung

MTD

MTD OHV Series Bedienungsanleitung

Kohler

Kohler COMMAND CH18-745 Bedienungsanleitung

Mercury

Mercury D4.2L D-Tronic Bedienungsanleitung

Selve

Selve SE Plus-RC Series Bedienungsanleitung

Perkins

Perkins 1206E-E66TA Bedienungsanleitung

Skov

Skov DA 174 Handbuch

Rossi

Rossi TX11 Series Bedienungsanleitung

Siemens

Siemens SIMOTICS T-1FW3 Merkblatt

AL-KO

AL-KO PRO 350 Bedienungsanleitung

MTU

MTU 12 V 4000 Lx4 Bedienungsanleitung

Nanni

Nanni N3.30 Gebrauchsanweisung

Nanni

Nanni N5.160 CR2 Bedienungsanleitung

KSB

KSB SuPreme Series Montageanleitung

Hiwin

Hiwin EM1 Series Bedienungsanleitung

Rotax

Rotax 912 i series Betriebsanleitung

Siemens

Siemens SIMOTICS XP 1MB1 Bedienungsanleitung

woodmizer D10 Leitfaden

Beliebte Motor Handbücher anderer Marken