woodmizer LT15 AL-KO Leitfaden
LT15 Trailer
Safety, Operation, Maintenance
& Parts Manual
LT15TRG Rev. A1.00 - A2.01
Safety is our #1 concern! Read and understand
all safety information and instructions before oper-
ating, setting up or maintaining this machine.
November 2010
Form #1729
ii 10doc111714 Table of Contents
Table of Contents Section-Page
SECTION 1 TRAILER INSTALLATION 1-1
1.1 Pre-Assembled Sawmill .........................................................................1-1
1.2 Unassembled Sawmill ............................................................................1-3
1.3 Up/Down & Feed Handle Relocation.....................................................1-4
1.4 Final Installation...................................................................................1-11
SECTION 2 TRAILER OPERATION 2-1
2.1 Preparing The Sawmill For Travel .........................................................2-1
2.2 Preparing The Sawmill For Operation ...................................................2-4
2.3 Loading A Log .......................................................................................2-7
SECTION 3 MAINTENANCE 3-1
SECTION 4 REPLACEMENT PARTS 4-1
4.1 Trailer (Complete) ..................................................................................4-1
4.2 Front Trailer Parts...................................................................................4-2
4.3 Rear Trailer Parts....................................................................................4-3
4.4 Outrigger Parts........................................................................................4-4
4.5 Winch Parts ............................................................................................4-5
4.6 Axle/Fender Parts ...................................................................................4-6
4.7 Saw Head Rest Pin/Bracket Parts...........................................................4-7
4.8 Up/Down Parts .......................................................................................4-8
INDEX I
Trailer Installation
Pre-Assembled Sawmill
Trailer Installation 1510doc111714 1-1
1
SECTION 1 TRAILER INSTALLATION
IMPORTANT! The trailer option is intended for use with LT15 sawmills Rev. E4.00
(LT15BS bed section Rev. E.00) and newer with three bed sections. LT15 sawmills prior
to Rev. E6.08 require modification to the mast to allow repositioning of the up/down sys-
tem (See Section 1.3).
1.1 Pre-Assembled Sawmill
If you are adding the LT15TRG trailer option to an assembled LT15 sawmill, the assem-
bled sawmill bed can be lifted onto the trailer frame. Be sure to use adequate manpower
and lifting equipment to safely lift and stabilize the sawmill during installation.
1. Disassemble the feed rope from the rear rope bracket and remove from the feed crank
pulley. Remove the rear feed rope bracket from the sawmill. Move the saw head to the
rear end of the bed and support with lifting equipment such as a forklift or hoist. Remove
the saw head from the bed and set aside.
2. Using adequate lifting equipment, lift the sawmill bed off the ground. Remove the legs.
See Figure 1-1.
3. Position the trailer next to the sawmill, oriented so the front of the sawmill is at the hitch
FIG. 1-1
Remove
legs from
sawmill
Disconnect feed rope,
remove bracket and
remove saw carriage
150193-1
Trailer Installation
Pre-Assembled Sawmill
1
1-2 1510doc111714 Trailer Installation
end of the trailer. Lower the trailer outriggers and use the jack handle to adjust the outrig-
gers to lift the trailer weight off the wheels and to level the trailer frame.
4. Disengage the trailer fender locking straps and lift the fenders from the trailer.
5. Lift the trailer winch assembly and pivot the winch down to the ground.
6. Pivot the saw head rest bracket down.
7. Position the sawmill onto the trailer frame, aligning the leg mounting holes with the holes
in the trailer frame. Secure the sawmill bed to the trailer frame with the provided mounting
bolts, bushings, washers and nuts.
See Figure 1-2.
8. Reassemble the saw head to the sawmill and replace the rear feed rope bracket. Leave
the feed rope disassembled until trailer installation is complete.
FIG. 1-2
5
150193-2
6
Adjust outriggers
to level trailer
frame
Jack
handle
½-13 x 6 ½” Hex
Head Bolt (6)
Bushing (8)
½-13 Hex
Nylon Lock
Nut (8)
½-13 x 3 ½” Hex
Head Bolt (2)
Pivot rest
bracket down
Lift and pivot
winch to ground
Lift fenders
from trailer
Washer (8) Secure bed to
trailer frame with
provided hardware
Trailer Installation
Unassembled Sawmill
Trailer Installation 1510doc111714 1-3
1
1.2 Unassembled Sawmill
If you are adding the LT15TRG trailer option to a new unassembled LT15 sawmill, the
sawmill bed can be assembled to the trailer frame. Be sure to use adequate manpower
and lifting equipment to safely lift and stabilize the sawmill during installation.
1. Lower the trailer outriggers and use the jack handle to adjust the outriggers to lift the
trailer weight off the wheels and to level the trailer frame.
2. Disengage the trailer fender locking straps and lift the fenders from the trailer.
3. Lift the trailer winch assembly and pivot the winch down to the ground.
4. Pivot the saw head rest bracket down.
5. Position the sawmill bed sections onto the trailer frame with the track position on the left
side of the trailer as viewed from the hitch end. Connect the bed sections as described in
the LT15 manual. Align the leg mounting holes with the holes in the trailer frame and
secure the bed to the trailer frame with the provided mounting bolts, bushings, washers
and nuts.
See Figure 1-3.
6. Refer to the LT15 manual to complete sawmill assembly and setup (skip the feed rope
installation until trailer installation is complete).
FIG. 1-3
3
150193-3
4
Adjust outriggers
to level trailer
frame
Jack
handle
½-13 x 6 ½” Hex
Head Bolt (6)
Bushing (8)
½-13 Hex
Nylon Lock
Nut (8)
½-13 x 3 ½” Hex
Head Bolt (2)
Pivot rest
bracket down
Lift and pivot
winch to ground
Lift fenders
from trailer
Washer (8)
Place bed sections
on trailer frame, connect
and secure with
provided hardware
Trailer Installation
Up/Down & Feed Handle Relocation
1
1-4 1510doc111714 Trailer Installation
1.3 Up/Down & Feed Handle Relocation
Because the sawmill sits higher when mounted to the optional trailer, parts are included
that allow you to relocate the up/down and feed crank handles to a lower position.
1. Move the saw head to rear of the sawmill and lower all the way down. Lower the saw
head until it rests on the bed to provide slack in the up/down chain.
2. Loosen the up/down chain lower sprocket mounting bolt and the chain tension bolt.
3. Disassemble the up/down chain master links from the mounting bracket and remove the
chain from the sawmill.
See Figure 1-4.
FIG. 1-4
150193-4
Loosen mounting
& tensioner bolts
Remove bottom
sprocket cover
Disassemble chain
from mounting bracket
Trailer Installation
Up/Down & Feed Handle Relocation
Trailer Installation 1510doc111714 1-5
1
4. Disassemble the feed handle/crank assembly from the sawmill mast.
5. Disassemble the up/down crank assembly and chain mounting bracket from the sawmill
mast.
See Figure 1-5.
FIG. 1-5
150193-5
Remove chain
mount bracket
Remove feed
handle & crank
Remove up/down
crank (shown with
optional gear reducer)
Trailer Installation
Up/Down & Feed Handle Relocation
1
1-6 1510doc111714 Trailer Installation
6. LT15 Rev. E4.00 - E6.07 only: Drill two 5/16” diameter holes in the mast vertical tube at
the locations specified. Tap the holes with 3/8-16 threads. Note: LT15 Rev. E6.08 include
a block with threaded hole welded at the upper location. LT15 Rev. E6.09 and newer
include a block with two threaded holes welded at this location.
See Figure 1-6.
FIG. 1-6
10”
1 ½”
½”
150194B
Drill 5/16” dia.
Tap 3/8-16
Trailer Installation
Up/Down & Feed Handle Relocation
Trailer Installation 1510doc111714 1-7
1
7. Use a C-clamp or vise to press the provided bearings into the up/down mounting bracket
housing. Be sure the bearings are oriented with the seals facing outward. To avoid dam-
aging the bearings, do not use a hammer to install.
8. Install the mounting bracket to the sawmill mast positioned two holes lower than the origi-
nal bracket. Use the existing hardware to secure the top of the bracket to the mast.
9. Install the new chain mount bracket at the bottom of the mast using the existing hardware
to secure.
See Figure 1-7.
FIG. 1-7
150193-6C
Press bearings
into housing
Use existing hardware
to mount bracket
Use existing hardware
to mount chain bracket
Trailer Installation
Up/Down & Feed Handle Relocation
1
1-8 1510doc111714 Trailer Installation
10. Disassemble the up/down crank assembly:
See Figure 1-8. Standard crank assembly: Use a 5/32” punch to remove the roll pin
securing the crank assembly to the sprocket/shaft weldment. Remove the crank assem-
bly and sprocket/shaft weldment from the mount bracket. Remove the two bolts, washers
and lock nuts to disassemble the dial from the mount bracket.
See Figure 1-9. Gear-reducer crank assembly: Disassemble the four bolts holding the
guard, dial and crank assembly to the mounting plate. Use a 5/32” hex wrench to remove
the two button head socket screws holding the sprockets to the hub. Use a 5/32” punch to
remove the roll pin securing the hub to the sprocket/shaft weldment. Remove the hub and
sprocket/shaft weldment from the mount bracket. Remove the two bolts and washers to
disassemble the mounting plate from the mount bracket.
FIG. 1-8
FIG. 1-9
150195-1
Crank Assembly
Roll Pin
Dial
Mount
Bracket
Sprocket/Shaft
Weldment
150196-1
Guard
Hub
Sprockets
Mounting
Plate
Crank
Assembly
Roll Pin
Dial
Mount
Bracket
Sprocket/Shaft
Weldment
Andere Handbücher für LT15 AL-KO
7
Inhaltsverzeichnis
Andere woodmizer Gesehen Handbücher
woodmizer
woodmizer LT10 Bedienungsanleitung
woodmizer
woodmizer LT30HD Bedienungsanleitung
woodmizer
woodmizer LT40HD Leitfaden
woodmizer
woodmizer LT60 Bedienungsanleitung
woodmizer
woodmizer LT15 AL-KO Bedienungsanleitung
woodmizer
woodmizer TVSE11S - SC Bedienungsanleitung
woodmizer
woodmizer LT70 Super Hydraulic Bedienungsanleitung
woodmizer
woodmizer TVS Bedienungsanleitung
woodmizer
woodmizer SVSE11S Handbuch
woodmizer
woodmizer LT15 Leitfaden
woodmizer
woodmizer LT40 AH Series Bedienungsanleitung
woodmizer
woodmizer LT70DC Bedienungsanleitung
woodmizer
woodmizer Autoclutch Option Bedienungsanleitung
woodmizer
woodmizer LT50HD Bedienungsanleitung
woodmizer
woodmizer LT20 Series Bedienungsanleitung
woodmizer
woodmizer LT40 Series Bedienungsanleitung
woodmizer
woodmizer MP360EB16U Bedienungsanleitung
woodmizer
woodmizer 1982 LT30 Bedienungsanleitung
woodmizer
woodmizer LT40DC Series Bedienungsanleitung
woodmizer
woodmizer LT40 MH Series Leitfaden
