Worcester Greenstar FS 42CDi Regular Bedienungsanleitung

UK/IE

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

8 716 115 217a (07.2008)

GREENSTAR

FS 30 & FS 42CDi Regular

FOR SEALED OR OPEN VENT CENTRAL HEATING SYSTEMS

THE APPLIANCE IS FOR USE WITH

NATURAL GAS OR L.P.G. (Cat II 2H3P TYPE C13, C33, C53 & C93)

NATURAL GAS:

GREENSTAR FS 30CDi REGULAR GC NUMBER 41-406-03

GREENSTAR FS 42CDi REGULAR GC NUMBER 41-406-04

LIQUID PETROLEUM GAS:

GREENSTAR FS 30CDi REGULAR GC NUMBER 41-406-05

GREENSTAR FS 42CDi REGULAR GC NUMBER 41-406-06

FLOOR STANDING RSF GAS-FIRED CONDENSING REGULAR BOILER

USER INSTRUCTIONS & CUSTOMER

CARE GUIDE

CONTACT INFORMATION

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

8 716 115 217a (07.2008)

PLEASE READ THESE INSTRUCTIONS

CAREFULLY BEFORE OPERATING YOUR

BOILER

THESE INSTRUCTIONS ARE APPLICABLE TO

THE WORCESTER, BOSCH GROUP BOILER

MODEL(S) STATED ON THE FRONT COVER

OF THIS MANUAL ONLY AND MUST NOT BE

USED WITH ANY OTHER MAKE OR MODEL OF

BOILER.

THE INSTRUCTIONS APPLY IN THE UK ONLY

AND SHOULD BE FOLLOWED EXCEPT FOR

ANY STATUTORY OBLIGATION.

IF YOU ARE IN ANY DOUBT CONTACT THE

WORCESTER, BOSCH GROUP TECHNICAL

SUPPORT.

DISTANCE LEARNING AND TRAINING

COURSES ARE AVAILABLE FROM

WORCESTER, BOSCH GROUP.

THIS BOILER MUST BE INSTALLED BY A

CORGI REGISTERED, COMPETENT PERSON.

FAILURE TO INSTALL CORRECTLY COULD

LEAD TO PROSECUTION.

PLEASE LEAVE THIS GUIDE, THE

INSTALLATION INSTRUCTIONS AND THE

COMPLETED BENCHMARK CHECKLIST

WITH THE USER.

NOTE: THE BENCHMARK CHECKLIST AND

SERVICE INTERVAL RECORD CAN BE

FOUND AT THE REAR OF THE

INSTALLATION, COMMISSIONING AND

SERVICE INSTRUCTIONS.

ABBREVIATIONS USED IN THIS BOOK:

NG - Natural Gas

LPG - Liquid Petroleum Gas

CH - Central Heating

SEDBUK - Seasonal Efficiency of Domestic

Boilers in the United Kingdom

WORCESTER BOSCH:

TECHNICAL: 08705 266241

SERVICE: 08457 256206

LITERATURE: 01905 752556

SALES: 01905 752640

WEBSITE: www.worcester-bosch.co.uk

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

MAINTENANCE ENERGY

SAVING

USING YOUR

APPLIANCE INTRODUCTION

GUARANTEE

CONTENTS

8 716 115 217a (07.2008)

INTRODUCTION

SAFETY PRECAUTIONS 2

GENERAL INFORMATION 3

GENERAL NOTES 4-5

USING YOUR APPLIANCE

CONTROLS 6-7

OPERATING THE APPLIANCE

Switching the appliance on/off 8

Setting the central heating temperature 8

Controlling central heating 8

Frost protection 9

Fault condition 10

MAINTENANCE

MAINTAINING YOUR BOILER 11

FAULT FINDING 12

FAULT OR BREAKDOWN 13

ENERGY SAVING

TIPS ON ENERGY SAVING 14-15

GUARANTEE

YOUR GUARANTEE 16

GUARANTEE REGISTRATION 17

Dedicated to heating comfort

Thank you for purchasing a Greenstar gas-fired condensing regular boiler manufactured

by Worcester, Bosch Group. The company prides itself on manufacturing boilers to the

strictest quality control standards throughout every stage of production.

Worcester, Bosch Group has led the field in innovative boiler design and performance for

more than 40 years. This heritage means all products are of exceptional quality and proven

reliability.

The Greenstar range in particular is extremely energy efficient, offering you economical

running costs and value for money. It sits in SEDBUK Band A, and is therefore amongst

the top energy rated boilers available.

There is also the reassurance of our no-nonsense 2 years parts and labour guarantee -

backed up by Worcester Total Cover, an optional complete maintenance scheme to keep

your boiler operating at peak condition and efficiency.

To find out more about Worcester, Bosch Group log onto www.worcester-bosch.co.uk .

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

INTRODUCTION

8 716 115 217a (07.2008)

SAFETY PRECAUTIONS

IF YOU SMELL GAS:

DON'T SMOKE OR STRIKE MATCHES.

DON'T TURN ELECTRICAL SWITCHES ON OR OFF.

DO PUT OUT NAKED FLAMES.

DO OPEN DOORS AND WINDOWS.

DO KEEP PEOPLE AWAY FROM THE AREA AFFECTED.

DO TURN OFF THE CONTROL VALVE AT THE METER.

DO CALL YOUR GAS COMPANY.

COMBUSTIBLE AND CORROSIVE MATERIALS:

Do not store or use any combustible materials (paper, thinners, paints etc.) inside or within

the vicinity of the boiler.

Chemically aggressive substances can corrode the boiler and invalidate any warranty.

FITTING & MODIFICATIONS

Fitting the boiler, any controls to the boiler and removal of the outer casing may only be

carried out by a competent engineer in accordance with the Gas Safety (Installation and Use)

Regulations.

Flue systems must not be modified in any way other than as described in the Installation

instructions and any misuse or unauthorised modifications to the boiler, flue or associated

components and systems could invalidate the warranty. The manufacturer accepts no liability

arising from any such actions. This does not affect your statutory rights.

SAFETY PRECAUTIONS

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

INTRODUCTION

GENERAL INFORMATION 3

SERVICING

The boiler must be serviced regularly by a competent, qualified person, such as a Worcester

service engineer or alternatively a British Gas or other CORGI registered person.

Always use original spares, to help maintain the economy, safety and reliability of the boiler

and have the Service Record completed in the Benchmark checklist.

IMPORTANT:- Ensure that the service engineer completes the Service Record in the

Benchmark checklist after each service.

The completed Benchmark checklist will be required in the event of any

warranty work and may be required by the local Building Control Inspector.

NOTE:

BENCHMARK STANDARD

‘Benchmark’ is a code of practice for correctly installing, commissioning and servicing of

domestic water heating boilers.

A Benchmark Checklist is provided by the manufacturer for the installer to complete ALL

details together with their CORGI registration number and sign to confirm that the boiler has

been installed and commissioned according to the manufacturer’s instructions.

HEALTH & SAFETY

The boiler contains no asbestos and no substances used in the construction process that

contravene the COSHH Regulations (Control of Substances Hazardous to Health Regulations

1988).

The Benchmark checklist and service interval record can be found at the

rear of the Installation, Commissioning and Servicing Instructions.

GENERAL INFORMATION

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

INTRODUCTION

8 716 115 217a (07.2008)

GENERAL NOTES

To get the best from your boiler please read

these instructions carefully.

SEALED HEATING SYSTEMS

If this boiler is fitted to a sealed heating system

which is pre-pressurised. Your installer will

advise you of the minimum and maximum

pressure which should be indicated on the

pressure gauge.

Check regularly that the pressure is maintained

and contact your installer or maintenance

engineer if a permanent significant drop in

pressure is indicated on the pressure gauge.

If the system loses pressure it should be re-

pressurised and the cause of the fall

investigated.

CENTRAL HEATING SYSTEMS

During the first few hours of operation of the

central heating system, check that all radiators

are being heated evenly. If the top of a radiator

is at a lower temperature than the bottom

then it should be vented by releasing air

through the venting screw at the top of the

radiator. Ask your installer to show you how

this is done.

This boiler is fitted to a sealed system;

repeated venting will reduce the quantity of

water in the system and this must be

replenished for safe and satisfactory operation

of the boiler.

Should water leaks be found in the system or

if excessive venting is required, then a service

engineer must be contacted to inspect the

installation and rectify any fault.

Only additives that are compatible with

aluminium may be used in the system. Any

incompatible additive used will invalidate the

guarantee.

CONDENSATE DRAIN

This is a condensing boiler and the terminal

will, at times give out a plume of water vapour.

This is quite normal.

The boiler also produces quantities of

condensate which is discharged regularly by

a trap within the boiler via a pump and pipe

to drain. This pipe must not be blocked or

altered in any way.

CLEARANCES - SERVICE

Your installer will have provided adequate

space around the boiler for safety and servicing

access. Do not restrict this space with the

addition of cupboards, shelves etc. next to

the boiler.

ROOM THERMOSTAT

A room temperature controller and

programmer should be fitted to control the

central heating. Refer to the instructions

supplied with the thermostat for information

on siting and setting.

THERMOSTATIC RADIATOR VALVES (TRV)

TRVs should fitted to all but one of the

radiators (or at least those in the sleeping

accommodation). The radiator without the

TRV must be in the same room as the room

thermostat, and must be uncontrolled and

unrestricted. The thermostatic radiator valves

should conform to the requirements of

BS2767:10.

GENERAL NOTES

600mm

15mm

5mm

410mm

1200mm

865mm

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

INTRODUCTION

8 716 115 217a (07.2008) GENERAL NOTES 5

BOILER CLEARANCES -

UNVENTILATED COMPARTMENT

The diagram opposite shows the minimum

space required to install and service the boiler

inside an unventilated compartment.

* Space required for unventilated areas with

a removable door or panel, but 600mm to a

fixed surface for servicing.

** This space can be reduced to 50mm for

one side only as long as both side clearances

add up to the total of both the side

measurements shown, or more.

Two examples are shown opposite, refer to

the ‘Installation, commissioning and servicing

instruction manual’ for further information.

Do not add cupboards, shelves etc. to restrict

the space around the boiler.

VENTILATION

This is a room sealed boiler and does not

require any air for combustion from inside the

property.

In spite of the requirements of BS 6798 and

BS 5440 there is no need for ventilation

openings to be provided in the compartment

because of the low heat loss from the boiler

casing, if the clearances shown are maintained.

BOILER CLEARANCES -

AIRING CUPBOARD

If the boiler is fitted into an airing cupboard

then the diagram opposite shows the minimum

clearances required around the boiler and

also the clearances for any shelf constructed

above the boiler.

If a compartment is built around the boiler

after installation, then the compartment must

be separated from the boiler space by a non-

combustible partition as described in BS 6798.

WARNING

Do not operate the boiler if the flue terminal

fitted on the outside wall or roof is obstructed

or damaged.

PUMP ANTI-SEIZURE

If there has been no heating demand for 24

hours, the boiler will run the system pump for

a few seconds. This is to reduce the possibility

of pump seizure during long periods of

inactivity which are usually more frequent

during the summer months.

GENERAL NOTES

800mm

50mm

100mm**

200mm*

25mm 100mm

200mm

100mm

25mm

100mm

900mm

600mm

1050mm

625mm 600mm

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

USING YOUR

APPLIANCE

8 716 115 217a (07.2008)

CONTROLS

A - MASTER SWITCH FOR ON/OFF

B - MAINS ON/OFF INDICATOR + FAULT DIAGNOSTIC LIGHT

C - CENTRAL HEATING TEMPERATURE CONTROL

D - BURNER ON INDICATOR LIGHT (GREEN)

E - FAULT RESET BUTTON

F - SERVICE BUTTON

G - NOT USED

H - DISPLAY

J - CENTRAL HEATING BOOST BUTTON

K - NOT USED

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

USING YOUR

APPLIANCE

8 716 115 217a (07.2008) CONTROLS 7

CONTROLS

TO ACCESS THE CONTROLS

Pull the centre top of the cover panel to

allow the cover to open.

CONTROLS

COVER

USER INSTRUCTIONS & CUSTOMER CARE GUIDE

USING YOUR

APPLIANCE

8OPERATING THE APPLIANCE 8 716 115 217a (07.2008)

OPERATING THE APPLIANCE

SWITCHING THE APPLIANCE ON/OFF

Switching on

Switch on the appliance by pressing the

master switch.

The indicator light shows blue

• The boiler runs for 15 minutes at minimum

heating output to fill the condensate trap, the

display (K) alternates between ‘-II-’ and the

central heating flow temperature. This occurs

every time the mains supply has been interrupted.

Switching off

Switch off the appliance by pressing the

master switch. The blue indicator light goes

out.

SETTING THE CENTRAL HEATING

TEMPERATURE

Turn the temperature control knob to the

desired level, between 35 °C and 88 °C.

When the burner is lit, the green indicator

light underneath the on/off switch is

illuminated.

CONTROLLING CENTRAL HEATING

Set the external timer to the correct time.

Set room thermostat to the desired room

temperature.

Set the thermostatic radiator valves to the

desired settings.

*---

1---

2---

3---

4---

5---

6---

Max ---

OFF

35 ºC

40 ºC

50 ºC

65 ºC

75 ºC

85 ºC

88 ºC

APPROXIMATE TEMPERATURES

Andere Handbücher für Greenstar FS 42CDi Regular

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Worcester Kessel Handbücher

Worcester

Worcester Greenstar Danesmoor 25kW Bedienungsanleitung

Worcester

Worcester Greenstar CDi Bedienungsanleitung

Worcester

Worcester 240 Combi BF Betriebsanleitung

Worcester

Worcester ZWBR 7-28 HE plus Benutzerhandbuch

Worcester

Worcester Greenstar i System Compact ErP Series Bedienungsanleitung

Worcester

Worcester Greenstar FS 42CDi Regular Bedienungsanleitung

Worcester

Worcester GREENSTAR UTILITY 18/25 Bedienungsanleitung

Worcester

Worcester 230 Combi RSF Benutzerhandbuch

Worcester

Worcester Benchmark Danesmoor Utility 12/14 Benutzerhandbuch

Worcester

Worcester 24Si II series Benutzerhandbuch

Worcester

Worcester GREENSTAR UTILITY Bedienungsanleitung

Worcester

Worcester Highflow 4.5 OF Benutzerhandbuch

Worcester

Worcester danesmoor 15/19 Bedienungsanleitung

Worcester

Worcester Greenstar Highflow 440 Bedienungsanleitung

Worcester

Worcester Greenstar 8000 Style Series Bedienungsanleitung

Worcester

Worcester 28Si Benutzerhandbuch

Worcester

Worcester GREENSTAR CDi CLASSIC SYSTEM Bedienungsanleitung

Worcester

Worcester GREENSTAR CAMRAY KITCHEN Bedienungsanleitung

Worcester

Worcester Greenstar 12Ri Handbuch

Worcester

Worcester Greenstar CDi Bedienungsanleitung

Worcester

Worcester Greenstar 8000 Life Series Bedienungsanleitung

Worcester

Worcester GREENSTAR CDi CLASSIC REGULAR ErP Bedienungsanleitung

Worcester

Worcester GREENSTAR UTILITY 32/50 Bedienungsanleitung

Worcester

Worcester Greenstar Ri Compact ErP Benutzerhandbuch

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung