WorkPro LS-Node Series Bedienungsanleitung

LS-Node

March 2019

LS-Node

LS-Node is the new range of network nodes from the lightShark family. Under the generic name LS-NODE,

the range includes three different models - LS-Node1, LS-Node2 and LS-Node4 - . These multiprotocol

RDM/DMX streaming devices are fully compatible with any lighting control or device that supports ArtNet or

sACN standards.

At WorkPro we hope it meets all your expectations.

Thank you very much for trusting us.

Introducción

LS-Node

LIghtShark series user manual

By WorkPro

Equipson S.A.

No part of this manual, including the products or software described herein, may be reproduced, transmitted,

or translated into any language in any form or by any means without the express prior written consent of

Equipson S.A.

The guarantee of the product or service will not be extended if: (1) the product is repaired, modied or

altered, unless the repair, modication or alteration is authorized in writing by Equipson SA; (2) the serial

number of the product cannot be clearly read or is not present.

EQUIPSON SA PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTIES OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES, MARKET

CONDITIONS OR ADJUSTMENTS FOR ANY PURPOSE. IN NO EVENT SHALL EQUIPSON SA, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY DAMAGES, WHETHER

INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL (INCLUDING DAMAGES FOR LOSS OF

PROFITS, BUSINESS, LOSS OF USE OR DATA, BUSINESS INTERRUPTION OR THE LIKE), EVEN IF

EQUIPSON SA HAS BEEN ADVISED THAT THE POSSIBILITY OF SUCH DAMAGES MAY ARISE FROM

ANY DEFECT OR ERROR IN ITS MANUALS OR PRODUCTS.

THE SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FOR INFORMATIONAL

PURPOSES ONLY AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND MAY NOT

BE USED AS A COMMITMENT BY EQUIPSON SA. EQUIPSON SA ASSUMES NO RESPONSIBILITY FOR

ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE

PRODUCTS AND/OR THE SOFTWARE DESCRIBED IN IT.

The products and corporate names appearing in this manual may (or may not) be trademarks or copyrights

of their respective companies, and are used herein only for identication or explanatory purposes and for the

benet of the owner, without intent to infringe such standards.

Policy

This equipment complies with EMC Directive 2004/108/EC and LVD 2006/95/EC.

This product is approved by the following safety standards: EN 60950~1:2006 + A11:2009 + A1:2010 +

A12:2011 + A2:2013

AND EMC standards EN55022: 2010 EN61000-3-3: 2013 EN55020:2007+ A11 EN61000-4-2: 2009

EN61000-4-3: 2006 + A1+ A2

ATTENTION: Any modication or change made to this device, unless explicitly approved by Equipson SA,

will void the authorization to use this device.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

For further details please contact: Equipson SA, AV El Saler nº14, Silla, Valencia, Spain. Telephone: +34

961 216 301 E-mail: [email protected]

LS-Node

1-Introduction

1.1 Safety instructions . . . . . . . .

1.2 Product Description . . . . . . . .

1.3 Box content . . . . . . . . .

1.4 Product overview . . . . . . . .

2-Conguration and Operation

2.1 Accesing the WebServer . . . . . . .

2.2 Port conguration . . . . . . . .

2.3 Setting ports as output . . . . . . . .

2.4 Setting ports as input . . . . . . . .

3-Updating & Reset

3.1 Firmware Update . . . . . . . .

3.2 Device Reset . . . . . . . . .

4-Support

4.1 Support . . . . . . . . .

LS-Node

Sección 1: Introduction

1.1 Safety Instructions

Please read the following Safety Notes carefully before starting to work with the product.

These notes include important safety information about installation, use, and maintenance.

• Before using this product, carefully read the instruction manual and keep it for future

reference.

• You must use a power supply according to the voltage marked on the rear panel, you

will void the warranty in case of using an inadequate voltage.

• Before connecting the device to the electric outlet ensure that the power cord is not

damaged.

• Always connect the device to the power supply supplied in the box.

• Install the device in a at and stable location.

• This product is rated IP20 so do not install near water or wetness, it is for indoor use

only.

• Place the device away from heat sources such as radiators. Make sure there are no

ammable materials near the device when it is in operation.

• Never connect the device to an electrical regulator or rheostat.

• To prevent the risk of shock, do not open or disassemble the unit.

• Never pull the power cord to turn off the device.

• If you install the device at a high place, please make sure that the bracket is properly

xed and secured.

• Equipson SA will not accept any liability for damage caused by unauthorized

modications or improper use of the device.

• If the device needs repair, contact Equipson SA or an authorized distributor.

LS-Node

1.3 Box Content

The following items are included in the box:

LS-Node device: Depending on model: LS-Node1, LS-Node2, LS-Node4.

USB power cable ( 1m ): connect one end to the LS-Node and the other end to the

USB power adapter.

USB Power Adapter: To power the LS-Node, it includes different types of plugs for

worldwide use. Simply select the correct adapter to plug it in.

1.2 Product Description

This series of small devices are available in the same format as ¼ rackmount LS-Core and

are powered via USB-C or via PoE, which is useful when used in installations where they

can be racked using the optional LS-AR 19 accessory.

All LS-Node devices have an integrated two-port Ethernet switch and are multiprotocol,

supporting industry standards ArtNet and sACN.

LS-Node is fully compatible with LightShark consoles and can also be congured via a

internal webserver, allowing users to congure parameters such as frame rate (15 to 40 hz),

rmware updates, independent routing of DMX ports (any universe can be routed

to any of the DMX ports independently) and usage modes.

All models have several usage modes:

-Single mode: RDM/DMX to ArtNet/sACN converter, congurable via web.

-Merger mode: where the LS-Node can receive different universes (via ArtNet/sACN or

DMX) and merge them in the same output via HTP/LTP modes.

-Backup mode: when the LS-Node works in Backup mode with two connected consoles,

the device can detect a connection loss from the main console and switch automatically

to the Backup console, with a maximum latency of 3 seconds.

NOTE The Firmware version used to make this manual is v.0.19.

ArtNet/sACN TYPE-C:5v,2A

POE

POWER

RESET

LS-Node

1.4 Product Overview

DMX OUT DMX IN

DMX-1 OUT DMX-1 IN DMX-2 OUT DMX-2 IN

DMX-1 IN/OUT DMX-2 IN/OUT DMX-3 IN/OUT DMX-4 IN/OUT

LS-Node 1.

Front view

Rear View

LS-Node 2.

LS-Node 4.

LS-Node

ArtNet/sACN TYPE-C:5v,2A

POE

POWER

RESET

1 2

3 4

1: Activity Led, if you receive Art-Net or sACN the led will ash quickly.

2: Link Led, indicates that the ethernet port is connected to the network.

3: Ethernet port A, which is a Neutrik etherCON connector with which to connect the

node to the network.

4: Ethernet port B, which is a Neutrik etherCON connector to connect the node to

the network. The B port (unlike the A port) allows you to power the Node through

P.o.E.

5: Power LED, which is illuminated when the Node is connected to the USB-C

power or to a P.o.E switch .

6: Reset switch, allows you to return to the original factory conguration of the

device.

7: USB Type-C port, to supply power to the Node. It is possible to power it from the

USB port of any computer or laptop, or a USB-C power supply. The device is

supplied with a USB power supply and a USB Type A-C cable.

8: Activity LED, the LED will illuminate Green when it is assigned an active universe.

DMX-1 IN/OUT DMX-2 IN/OUT DMX-3 IN/OUT DMX-4 IN/OUT

LS-Node

Product Dimensions

LS-Node

Sección 2: Conguration & Operation

2.1 Web Server Access

LS-Node devices are congured through WebServer. To access, connect your LS-Node

device to the LAN and from a laptop, tablet, or smartphone ... access the IP address 2.0.0.1

2.0.0.1

NOTE Note that the computer or tablet from which you want to connect must be in the same

subnet as the nodes.

NOTE The use of Safari, FireFox, or Chrome web browsers is recommended.

NOTE If you use iOS devices, the minimum software version required in iOS9

NOTE It is possible to congure LS-Node devices over the Internet, you only need to

redirect port 80 on your router to the IP address of the device.

From the DEVICE SETTINGS window it is possible to adjust the IP address of the devices

and their name.

2.0.0.1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere WorkPro TV-Tuner Handbücher

WorkPro

WorkPro BLR2 MKII Bedienungsanleitung

Beliebte TV-Tuner Handbücher anderer Marken

KWorld

KWorld PE310SE Bedienungsanleitung

COMPRO

COMPRO M505 - STARTUP Bedienungsanleitung

Genius

Genius TVGo DVB-T31 Bedienungsanleitung

Zinwell

Zinwell ZAT-332 Bedienungsanleitung

RGBlink

RGBlink TAO 1mini-HN Bedienungsanleitung

TViX

TViX PVR R-2200 Bedienungsanleitung

Xavix

Xavix Xavixport Bedienungsanleitung

Peak

Peak NET-TV Bedienungsanleitung

Fracarro

Fracarro SAF-HD 10 Bedienungsanleitung

Eonon

Eonon E0770 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-NOVA-T-Stick Bedienungsanleitung

Digital Devices

Digital Devices Octopus Net Bedienungsanleitung

Gericom

Gericom USB 2.0 DVB-T Tuner Bedienungsanleitung

Manta

Manta DVBT013T2 Bedienungsanleitung

Kenwood

Kenwood KTC-D500E Bedienungsanleitung

AVIWEST

AVIWEST DMNG PRO 100 Bedienungsanleitung

Abode

Abode IP Streaming Camera Bedienungsanleitung

PS Audio

PS Audio AIRLENS Kurzanleitung