WTC MP058 Bedienungsanleitung

MP058 Rev. B User's Manual

Intel Triton FX Motherboard

Table of Contents

Chapter 1: Introduction

Foreword .................................................. 1-1

Mainboard Features ........................................ 1-3

Chapter 2: Mainboard Setup

Jumper and Connectors Reference ........................... 2-1

CPU Internal Clock Selector ............................... 2-3

SRAM Configuration ........................................ 2-5

AT Bus Speed Selector ..................................... 2-6

Printer Port ECP Function Selector ........................ 2-6

Flash ROM Voltage Selector ................................ 2-6

Mainboard Connectors ...................................... 2-9

CMOS Charge/ Discharge .................................... 2-9

Chapter 3: AWARD BIOS Setup

Standard CMOS Setup ....................................... 3-3

BIOS Features Setup ....................................... 3-5

CHIPSET Features Setup .................................... 3-8

POWER Management Setup .................................... 3-11

PCI Configuration Setup.................................... 3-14

Load BIOS Defaults ........................................ 3-16

Load Setup Defaults ....................................... 3-16

PASSWORD Setting .......................................... 3-18

IDE HDD Auto Detection .................................... 3-19

IDE Low Level Format ...................................... 3-19

Save & Exit Setup ......................................... 3-21

Exit Without Saving ....................................... 3-21

Appendix A

BIOS-Supported Enhanced IDE Features....................... A-l

Large IDE Hard Disks....................................... A-2

Faster Data Transfer....................................... A-3

page 1-1

Foreword

========

This manual is designed to provide the basic necessary information for the end

user to understand and properly use the MP058 mainboard. The mainboard ensures

superlative performance and complete compatibility with industry standards,

which incorporating many technical enhancements.

Trademarks

==========

WTC is a registered trademark of Win Technologies Co., Ltd. All trademarks

belong to their registered owner.

Checklist

=========

Your MP058 Cache package contains the following:

* MP058 Cache mainboard

* User's Manual.

* HDD/FDD Cable

* Coml & Com2 Cable

* Printer Cable

page 1-2

Precautions

===========

Make sure you ground yourself before handling the mainboard or other system

components. Electrostatic discharge will damage mainboard. Note that you must

take special precaution when handling the mainboard in dry or air-conditioned

environments.

The precaution below is to protect the mainboard from electrostatic discharge.

* Do not remove the anti-static packaging until you are ready to install the

mainboard and other system components.

* Ground yourself before removing any system component from its protective

anti-static packaging. To ground yourself, grasp the expansion slot covers or

other unpainted portion computer chassis.

* Frequently ground yourself while working ,or use a grounding strap.

* Handle the mainboard by the edges and avoid touching its components.

page 1-3

Mainboard Features

==================

* Intel Triton PCI chipset: 82437 (TSC)/82438(TDP)/82371FB (PIIX)

* Support P54C/P55C Microprocessor, system running up to 180 Mhz

* Support High performance 32 bits PCI local bus and provide four PCI bus

master

* Support four 16 bits ISA system bus I/O slot

* Cache Optional up to 512KB , using DIP type SRAM (Asynchronous mode) or

cache module Synchronous pipeline burst (burst mode)

* Direct mapped organization with write through / write back selection

* Main memory (DRAM) support from 4MB to 128MB, using standard page mode or

EDO mode DRAM

* Support Enhance IDE onboard

* PnP (Plug & Play) compatible L/O (Serial port, Parallel port, FDC ) onboard

page 2-1

Jumper and Connectors Reference

===============================

Before installing the mainboard, make sure that the jumper setting are

properly set for your configuration. The function of different jumpers are

respectively as follows:

CPU Internal Clock Multiplier ................................ JP31, JP32

CPU Clock Frequency Selector ................................. JP17, JP18

CPU Voltage Selector ......................................... JP36, JP37

Cache Option ................................................. JP20

SRAM Voltage Selector ........................................ JP29, JP30

Flash ROM Voltage Selector ................................... JP14

Printer Port ECP function Selector ........................... JP5, JP6

CMOS Charge / Discharge ...................................... JP13

AT Bus Speed Selector ........................................ JP15

CPU Internal Cache Write Back / Write Through Select.......... JP23

Mainboard Connectors:

Onboard HDD LED Connector .................................... J3

Reset Switch Connector........................................ J2

Speaker Connector ............................................ J1

Keylock and Power LED Connector............................... J4

PS/2 mouse Connector ......................................... MS2

Keyboard Connector ........................................... KB1

Power Supply Connector ....................................... PW1

Turbo Switch Connector(T/SW) ................................. TB/SW

Turbo LED Connector (T/LED) .................................. TB/LED

Jumper Caps reference :

Red Jumper for Voltage Selector

White Jumper for CPU Type

Yellow Jumper for Clock Selector

Blue Jumper for Cache Option

Black Jumper for Other

page 2-3

Mainboard Setup

===============

P54C CPU JUMPER SETTING

=======================

When you look for jumper setting for H/W configuration. Please refer to page

2-4 the MP058 Mainboard placement chart.

CPU SPEED CPU Clock Selector CPU Internal Clock Selector

Yellow Jumper Cap Yellow Jumper Cap

JP18 JP17 JP31 JP32

P54C-75 Mhz CLOSE CLOSE (50 Mhz) 1-2 1-2 (x1.5)

P54C-90 Mhz CLOSE OPEN (60Mhz) 1-2 1-2 (x1.5)

P54C-100 Mhz CLOSE CLOSE (50 Mhz) 1-2 2-3 (x2 )

OPEN CLOSE (66.6Mhz) 1-2 1-2 (x1.5)

P54C-120 Mhz CLOSE OPEN (60Mhz) 1-2 2-3 (x2)

P54C-133 Mhz OPEN CLOSE (66.6Mhz) 1-2 2-3 (x2)

P54C-150 Mhz CLOSE OPEN (60Mhz) 2-3 2-3 (x2.5)

P54C-166 Mhz OPEN CLOSE (66.6Mhz) 2-3 2-3 (x2.5)

P54C-180 Mhz CLOSE OPEN (60Mhz) 2-3 1-2 (x3)

P54CST-200Mhz OPEN CLOSE (66.6Mhz) 2-3 1-2 (x3)

CYRIX 6x86 CPU JUMPER SETTING

=============================

CPU SPEED CPU Clock Selector CPU Internal Clock Selector

Yellow Jumper Cap Yellow Jumper Cap

JP18 JP17 JP31 JP32

6x86-P120(100 Mhz) CLOSE CLOSE (50Mhz) 1-2 2-3 (x2)

6x86-P150(120 Mhz) CLOSE OPEN (60Mhz) 1-2 2-3 (x2)

6x86-P166(133 Mhz) OPEN CLOSE (66 Mhz) 1-2 2-3 (x2)

NOTE: This motherboard only can support single voltage CPU.

CPU VOLTAGE SELECTOR Red Jumper Cap

===================================

JP36 JP37

CLOSE OPEN 3.38 Volts for Intel P54C, Cyrix 6x86 Standard CPU Type

page 2-5

SRAM Configuration

==================

SRAM Configuration is used to configure the external cache of the mainboard.

External cache can be configured by using 32K*8 and 64K*8 DIP type SRAM or

synchronous cache module.

There are 3 types external cache configuration.

A. DIP Type SRAM (Asynchronous Cache with pin legs)

JP20 SRAM TAG RAM

256K cache size 1-2 32K*8 8K*8 / 16K*8 / 32K*8

512K cache size 2-3 64K*8 16K*8 / 32K*8

Note: Please use mix (3/5 volt) or 3 volt DIP cache.

B. Cache Module With Built-in TAG RAM(Synchronous Cache)

Please remove DIP type SRAM on the mainboard because Asynchronous and

Synchronous can't be simultaneously installed.

C. Cache Module Without Built-in TAG RAM (Synchronous Cache)

JP20 TAG RAM

256K cache size 1-2 8K * 8 / 16K * 8 / 32K * 8 TAG RAM

on the U19 socket

512K cache size 2-3 16K*8 / 32K * 8 TAG RAM

on the U19 socket

page 2-6

SRAM Voltage Selector

=====================

MP058 provides two types of voltage value for the SRAM, 5V voltage for

mix-mode DIP type SRAM , 3.3V voltage for 3.3V DIP type SRAM and synchronous

cache module.

JP29 JP30

OPEN 1-2,3-4,5-6 for MIX Mode SRAM

1-2,3-4,5-6 OPEN for 3.3 Volts DIP SRAM or

Synchronous Cache Module

AT Bus Speed Selector Yellow jumper Cap

=======================================

JP15

1-2 PCI Clock 1/3 (for higher speed)

2-3 PCI Clock 1/4

Note: Please use 1/4 clock for old version add-on card.

Printer Port ECP Function Selector

==================================

JP5 JP6

1-2 1-2 for ECP Mode

2-3 2-3 for Normal Mode

Flash ROM Voltage Selector Red jumper Cap

=========================================

JP14

OPEN EPROM

1-2 Flash ROM 12 Volts ( Intel Brand )

2-3 Flash ROM 5 Volts ( SST or Winbond Brand)

Note: The brand name of BIOS is under the BIOS.

page 2-7

Memory Configuration

====================

Memory Module Combinations

Bank O Bank 1 Total Memory Using Sockets

Socket 1 & 2 Socket 3 & 4 1 through 4

4MB x 2 None 8MB

8MB x 2 None 16MB

16MB x 2 None 32MB

32MB x 2 None 64MB

None 4MB x 2 8MB

None 8MB x 2 16MB

None 16MB x 2 32MB

None 32MB x 2 64MB

4MB x 2 4MB x 2 16MB

4MB x 2 8MB x 2 24MB

4MB x 2 16MB x 2 40MB

4MB x 2 32MB x 2 64MB

8MB x 2 4MB x 2 24NB

8MB x 2 8MB x 2 32MB

8MB x 2 16MB x 2 48MB

8MB x 2 32MB x 2 80MB

16MB x 2 4MB x 2 40MB

16MB x 2 8MB x 2 48MB

16MB x 2 16MB x 2 64MB

16MB x 2 32MB x 2 96MB

32MB x2 4MB x 2 72MB

32MB x2 8MB x 2 80MB

32MB x 2 16MB x 2 96MB

32MB x 2 32MB x2 I28MB

IMPORTANT: Do not use SIMM modules with more that 24 chips per module with

this mainboard. Module with more that 24 chips exceeds the design

specification of the memory subsystem and will cause unreliable

operation.

page 2-9

CMOS Charge / Discharge slack jumper Cap

========================================

CMOS Charge / Discharge is used to discharge and charge CMOS. If you discharge

the CMOS all the data will be erased.

JP13

OPEN Charge CMOS

CLOSE Reset CMOS

Mainboard Connectors

====================

J1 Speaker connector will be connected the speaker of your computer case.

J2 Reset Switch connector will be connected in your computer case front

panel. Resetting the system, it will restart the computer from

self-test without turning off the power supply. This connection is

always off position.

J3 Onboard HDD LED connector will be connected in your computer case

front panel.

J4 Keylock and Power LED connector will be connected in your computer

case front panel. Keylock is used to lock the keyboard. Power LED will

light up when you turn on your power supply.

MS1 PS/2 Mouse connector , this is used for PS/2 mouse. (In mainframe

case) Note: PS/2 mouse cable is optional.

KB1 Keyboard connector ,this is used for inputting signal from the

keyboard.

PW1 Power Supply connector is connected from the output of the power

supply. Most of the power supply has two connectors which will be

connected to the mainboard. Each connector has six wire , two of the

wires are black. To connect to the mainboard, make sure that the black

wire is in the middle. Wrong connection will cause damage to the

mainboard.

TB/SW Turbo Switch Connector will be connected in your computer case front

panel.

TB/LED Turbo LED Connector will be connected in your computer case front

panel.

page 3-1

AWARD BIOS SETUP

Award BIOS support plug and play function and has a built-in setup program

that allows the users to modify the basic system configuration. This type of

information is stored in CMOS so that it retains the setup information when

the power is turned off.

1. Turn on or reboot the system. when the below message appears at the

bottom of the screen during the POST ( Power On Self Test ) press DEL

key to enter setup.

2. Press the DEL key to enter the Award BIOS program and the main menu

will appear on the screen. The main menu allows you to select from ten

setup functions and two exit choices.

3. For the safe, please select "LOAD SETUP DEFAULTS" for BIOS setup.



Andere WTC Hauptplatine Handbücher

WTC

WTC MP060 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung