Wunda Smart Connection Box Bedienungsanleitung

Smart Connection

Box

Installation Guide

General information

⚠Note: large metal objects located

in the vicinity of or between

the Smart Hub and the Smart

Connection Box may have

anegative effect on the quality

ofradio transmission between the

devices. External antenna should

be placed vertically. The device

should be connected to a single-

phase power system according

tothe standards in place.

The connection method is

described in this manual.

Dismounting of the housing,

incorrect assembly or use,

and operation contrary to the

guidelines set forth in this manual

will result inthe loss of product

warranty andcause the risk of

electric shock.

⚠Before starting the installation

process make sure that there

is novoltage on the connection

cables. Installation should be

performed with a at screwdriver

(upto 3mm in diameter).

To ensure correct operation of

the device, make sure that it is

transported, stored andused

appropriately.

The Smart Connection Box controls

Electronic Actuators, circulating pump

andheat source or zone valve.

The Smart Connection Box is a part

oftheheat management system for

yourhome.

One Smart Hub supports up to 4 Smart

Connection Boxes.

The

Smart Connection Box has

a range of functions:

•

Control

Electronic Actuators

•

Supports up to 12 heating zones;

•

Controls the

circulating pump manifold

;

•

Is equipped with a

potential-free

contact (relay)

for controlling an

external heating source/ zone valve.



















Wunda

The device consists of the following

components:

 230V power mains input

 output for the 3D valve

 relay output for 230V

the circulating pump, max 0.5A

12 outputs for electronic actuators

Device appearance

relay output for the heat source,

max 3A

status LED

pairing button

 temperature input KTY-81-210

protective earthing

antenna

Manufacturer

Wunda Group PLC

Unit 10

Kingsway Buildings, Kingsway

Bridgend Industrial Estate,

Bridgend,

Glamorgan,

CF31 3YH

If for any reason you need to return your

Wunda Smart products, simply return

the product in its orginal box to us at the

above address. Any return is subject to

our refund policy so please don’t forget

to check the terms and conditions.

By using Wunda Smart and other Wunda

Smart products you agree to our terms

and conditions, which can be found on

our website www.wundasmart.com

Smart Connection

Box

Installation Guide

General information

⚠Note: large metal objects located

in the vicinity of or between

the Smart Hub and the Smart

Connection Box may have

anegative effect on the quality

ofradio transmission between the

devices. External antenna should

be placed vertically. The device

should be connected to a single-

phase power system according

tothe standards in place.

The connection method is

described in this manual.

Dismounting of the housing,

incorrect assembly or use,

and operation contrary to the

guidelines set forth in this manual

will result inthe loss of product

warranty andcause the risk of

electric shock.

⚠Before starting the installation

process make sure that there

is novoltage on the connection

cables. Installation should be

performed with a at screwdriver

(upto 3mm in diameter).

To ensure correct operation of

the device, make sure that it is

transported, stored andused

appropriately.

The Smart Connection Box controls

Electronic Actuators, circulating pump

andheat source or zone valve.

The Smart Connection Box is a part

oftheheat management system for

yourhome.

One Smart Hub supports up to 4 Smart

Connection Boxes.

The

Smart Connection Box has

a range of functions:

•

Control

Electronic Actuators

•

Supports up to 12 heating zones;

•

Controls the

circulating pump manifold

;

•

Is equipped with a

potential-free

contact (relay)

for controlling an

external heating source/ zone valve.



















Wunda

The device consists of the following

components:

 230V power mains input

 output for the 3D valve

 relay output for 230V

the circulating pump, max 0.5A

12 outputs for electronic actuators

Device appearance

relay output for the heat source,

max 3A

status LED

pairing button

 temperature input KTY-81-210

protective earthing

antenna

Manufacturer

Wunda Group PLC

Unit 10

Kingsway Buildings, Kingsway

Bridgend Industrial Estate,

Bridgend,

Glamorgan,

CF31 3YH

If for any reason you need to return your

Wunda Smart products, simply return

the product in its orginal box to us at the

above address. Any return is subject to

our refund policy so please don’t forget

to check the terms and conditions.

By using Wunda Smart and other Wunda

Smart products you agree to our terms

and conditions, which can be found on

our website www.wundasmart.com

Smart Connection

Box

Installation Guide

General information

⚠Note: large metal objects located

in the vicinity of or between

the Smart Hub and the Smart

Connection Box may have

anegative effect on the quality

ofradio transmission between the

devices. External antenna should

be placed vertically. The device

should be connected to a single-

phase power system according

tothe standards in place.

The connection method is

described in this manual.

Dismounting of the housing,

incorrect assembly or use,

and operation contrary to the

guidelines set forth in this manual

will result inthe loss of product

warranty andcause the risk of

electric shock.

⚠Before starting the installation

process make sure that there

is novoltage on the connection

cables. Installation should be

performed with a at screwdriver

(upto 3mm in diameter).

To ensure correct operation of

the device, make sure that it is

transported, stored andused

appropriately.

The Smart Connection Box controls

Electronic Actuators, circulating pump

andheat source or zone valve.

The Smart Connection Box is a part

oftheheat management system for

yourhome.

One Smart Hub supports up to 4 Smart

Connection Boxes.

The

Smart Connection Box has

a range of functions:

•

Control

Electronic Actuators

•

Supports up to 12 heating zones;

•

Controls the

circulating pump manifold

;

•

Is equipped with a

potential-free

contact (relay)

for controlling an

external heating source/ zone valve.



















Wunda

The device consists of the following

components:

 230V power mains input

 output for the 3D valve

 relay output for 230V

the circulating pump, max 0.5A

12 outputs for electronic actuators

Device appearance

relay output for the heat source,

max 3A

status LED

pairing button

 temperature input KTY-81-210

protective earthing

antenna

Manufacturer

Wunda Group PLC

Unit 10

Kingsway Buildings, Kingsway

Bridgend Industrial Estate,

Bridgend,

Glamorgan,

CF31 3YH

If for any reason you need to return your

Wunda Smart products, simply return

the product in its orginal box to us at the

above address. Any return is subject to

our refund policy so please don’t forget

to check the terms and conditions.

By using Wunda Smart and other Wunda

Smart products you agree to our terms

and conditions, which can be found on

our website www.wundasmart.com

Smart Connection

Box

Installation Guide

General information

⚠Note: large metal objects located

in the vicinity of or between

the Smart Hub and the Smart

Connection Box may have

anegative effect on the quality

ofradio transmission between the

devices. External antenna should

be placed vertically. The device

should be connected to a single-

phase power system according

tothe standards in place.

The connection method is

described in this manual.

Dismounting of the housing,

incorrect assembly or use,

and operation contrary to the

guidelines set forth in this manual

will result inthe loss of product

warranty andcause the risk of

electric shock.

⚠Before starting the installation

process make sure that there

is novoltage on the connection

cables. Installation should be

performed with a at screwdriver

(upto 3mm in diameter).

To ensure correct operation of

the device, make sure that it is

transported, stored andused

appropriately.

The Smart Connection Box controls

Electronic Actuators, circulating pump

andheat source or zone valve.

The Smart Connection Box is a part

oftheheat management system for

yourhome.

One Smart Hub supports up to 4 Smart

Connection Boxes.

The

Smart Connection Box has

a range of functions:

•

Control

Electronic Actuators

•

Supports up to 12 heating zones;

•

Controls the

circulating pump manifold

;

•

Is equipped with a

potential-free

contact (relay)

for controlling an

external heating source/ zone valve.



















Wunda

The device consists of the following

components:

 230V power mains input

 output for the 3D valve

 relay output for 230V

the circulating pump, max 0.5A

12 outputs for electronic actuators

Device appearance

relay output for the heat source,

max 3A

status LED

pairing button

 temperature input KTY-81-210

protective earthing

antenna

Manufacturer

Wunda Group PLC

Unit 10

Kingsway Buildings, Kingsway

Bridgend Industrial Estate,

Bridgend,

Glamorgan,

CF31 3YH

If for any reason you need to return your

Wunda Smart products, simply return

the product in its orginal box to us at the

above address. Any return is subject to

our refund policy so please don’t forget

to check the terms and conditions.

By using Wunda Smart and other Wunda

Smart products you agree to our terms

and conditions, which can be found on

our website www.wundasmart.com

Wiring diagram:

Power supply 230V, ~50Hz

IP rating IP20

IEC

protection class II

Permissible

range of ambient

temperatures

from 5–40°C,

without

condensation

Pump circuit load to 0.5A

Electronic

actuator circuit

load

12×230V, 20W

max Per Channel

Internal Fuses 5A

Radio

communications:

869.85MHz,

two-way

Maximum trans-

mitter power <5 dBm e.r.p.

Antenna: yes (supplied)

Technical data

The Smart Connection Box must

beinstalled in asuitable location above

the manifold within reach of the actuator

power cables.

All installation and connection steps

should be performed by appropriately

qualied and authorized persons

inaccordance with applicable

regulationsand standards.

1. Installation of the Smart Connection

Box should be installed via fused spur.

2. Isolate and turn off spur from mains

power and connect the Smart

Connection Box to the spur 

3. Connect to electronic actuators

installed on the manifold in correct

order torelevant contacts 

4. Connect manifold pump

to contact no 

5. If you want to switch heat source/

zone valve, connect to relay output 

6. If you want to use a 3d/4d valve* with

atemperature sensor, connect your

valve to and the temperature sensor

into terminals 

Without the temperature sensor

connected, the 3d/4d valve will

notoperate

7. Turn on the power for your Smart

Connection Box

Connecting to manifold

*3D/4D valves not supplied by Wunda

Ensure that your Smart Hub is correctly

installed and registered.

Open the WundaSmart application

and log in to your Smart Hub, select the

Devices from main menu and choose

Smart Connection Box.

Registering the device

You have 30 seconds to pair the Smart

Connecton Box. Press and hold button 

and wait for the LED light to turn green.

The installed Smart Connection Box will

appear on the device list.

Congure heating zones (rooms) in your

applicaction.

12× zone valve

3D valve

heating source

pump

temp.

sensor

1 2

~















Wiring diagram:

Power supply 230V, ~50Hz

IP rating IP20

IEC

protection class II

Permissible

range of ambient

temperatures

from 5–40°C,

without

condensation

Pump circuit load to 0.5A

Electronic

actuator circuit

load

12×230V, 20W

max Per Channel

Internal Fuses 5A

Radio

communications:

869.85MHz,

two-way

Maximum trans-

mitter power <5 dBm e.r.p.

Antenna: yes (supplied)

Technical data

The Smart Connection Box must

beinstalled in asuitable location above

the manifold within reach of the actuator

power cables.

All installation and connection steps

should be performed by appropriately

qualied and authorized persons

inaccordance with applicable

regulationsand standards.

1. Installation of the Smart Connection

Box should be installed via fused spur.

2. Isolate and turn off spur from mains

power and connect the Smart

Connection Box to the spur 

3. Connect to electronic actuators

installed on the manifold in correct

order torelevant contacts 

4. Connect manifold pump

to contact no 

5. If you want to switch heat source/

zone valve, connect to relay output 

6. If you want to use a 3d/4d valve* with

atemperature sensor, connect your

valve to and the temperature sensor

into terminals 

Without the temperature sensor

connected, the 3d/4d valve will

notoperate

7. Turn on the power for your Smart

Connection Box

Connecting to manifold

*3D/4D valves not supplied by Wunda

Ensure that your Smart Hub is correctly

installed and registered.

Open the WundaSmart application

and log in to your Smart Hub, select the

Devices from main menu and choose

Smart Connection Box.

Registering the device

You have 30 seconds to pair the Smart

Connecton Box. Press and hold button 

and wait for the LED light to turn green.

The installed Smart Connection Box will

appear on the device list.

Congure heating zones (rooms) in your

applicaction.

12× zone valve

3D valve

heating source

pump

temp.

sensor

1 2

~















Wiring diagram:

Power supply 230V, ~50Hz

IP rating IP20

IEC

protection class II

Permissible

range of ambient

temperatures

from 5–40°C,

without

condensation

Pump circuit load to 0.5A

Electronic

actuator circuit

load

12×230V, 20W

max Per Channel

Internal Fuses 5A

Radio

communications:

869.85MHz,

two-way

Maximum trans-

mitter power <5 dBm e.r.p.

Antenna: yes (supplied)

Technical data

The Smart Connection Box must

beinstalled in asuitable location above

the manifold within reach of the actuator

power cables.

All installation and connection steps

should be performed by appropriately

qualied and authorized persons

inaccordance with applicable

regulationsand standards.

1. Installation of the Smart Connection

Box should be installed via fused spur.

2. Isolate and turn off spur from mains

power and connect the Smart

Connection Box to the spur 

3. Connect to electronic actuators

installed on the manifold in correct

order torelevant contacts 

4. Connect manifold pump

to contact no 

5. If you want to switch heat source/

zone valve, connect to relay output 

6. If you want to use a 3d/4d valve* with

atemperature sensor, connect your

valve to and the temperature sensor

into terminals 

Without the temperature sensor

connected, the 3d/4d valve will

notoperate

7. Turn on the power for your Smart

Connection Box

Connecting to manifold

*3D/4D valves not supplied by Wunda

Ensure that your Smart Hub is correctly

installed and registered.

Open the WundaSmart application

and log in to your Smart Hub, select the

Devices from main menu and choose

Smart Connection Box.

Registering the device

You have 30 seconds to pair the Smart

Connecton Box. Press and hold button 

and wait for the LED light to turn green.

The installed Smart Connection Box will

appear on the device list.

Congure heating zones (rooms) in your

applicaction.

12× zone valve

3D valve

heating source

pump

temp.

sensor

1 2

~















Wiring diagram:

Power supply 230V, ~50Hz

IP rating IP20

IEC

protection class II

Permissible

range of ambient

temperatures

from 5–40°C,

without

condensation

Pump circuit load to 0.5A

Electronic

actuator circuit

load

12×230V, 20W

max Per Channel

Internal Fuses 5A

Radio

communications:

869.85MHz,

two-way

Maximum trans-

mitter power <5 dBm e.r.p.

Antenna: yes (supplied)

Technical data

The Smart Connection Box must

beinstalled in asuitable location above

the manifold within reach of the actuator

power cables.

All installation and connection steps

should be performed by appropriately

qualied and authorized persons

inaccordance with applicable

regulationsand standards.

1. Installation of the Smart Connection

Box should be installed via fused spur.

2. Isolate and turn off spur from mains

power and connect the Smart

Connection Box to the spur 

3. Connect to electronic actuators

installed on the manifold in correct

order torelevant contacts 

4. Connect manifold pump

to contact no 

5. If you want to switch heat source/

zone valve, connect to relay output 

6. If you want to use a 3d/4d valve* with

atemperature sensor, connect your

valve to and the temperature sensor

into terminals 

Without the temperature sensor

connected, the 3d/4d valve will

notoperate

7. Turn on the power for your Smart

Connection Box

Connecting to manifold

*3D/4D valves not supplied by Wunda

Ensure that your Smart Hub is correctly

installed and registered.

Open the WundaSmart application

and log in to your Smart Hub, select the

Devices from main menu and choose

Smart Connection Box.

Registering the device

You have 30 seconds to pair the Smart

Connecton Box. Press and hold button 

and wait for the LED light to turn green.

The installed Smart Connection Box will

appear on the device list.

Congure heating zones (rooms) in your

applicaction.

12× zone valve

3D valve

heating source

pump

temp.

sensor

1 2

~















Wiring diagram:

Power supply 230V, ~50Hz

IP rating IP20

IEC

protection class II

Permissible

range of ambient

temperatures

from 5–40°C,

without

condensation

Pump circuit load to 0.5A

Electronic

actuator circuit

load

12×230V, 20W

max Per Channel

Internal Fuses 5A

Radio

communications:

869.85MHz,

two-way

Maximum trans-

mitter power <5 dBm e.r.p.

Antenna: yes (supplied)

Technical data

The Smart Connection Box must

beinstalled in asuitable location above

the manifold within reach of the actuator

power cables.

All installation and connection steps

should be performed by appropriately

qualied and authorized persons

inaccordance with applicable

regulationsand standards.

1. Installation of the Smart Connection

Box should be installed via fused spur.

2. Isolate and turn off spur from mains

power and connect the Smart

Connection Box to the spur 

3. Connect to electronic actuators

installed on the manifold in correct

order torelevant contacts 

4. Connect manifold pump

to contact no 

5. If you want to switch heat source/

zone valve, connect to relay output 

6. If you want to use a 3d/4d valve* with

atemperature sensor, connect your

valve to and the temperature sensor

into terminals 

Without the temperature sensor

connected, the 3d/4d valve will

notoperate

7. Turn on the power for your Smart

Connection Box

Connecting to manifold

*3D/4D valves not supplied by Wunda

Ensure that your Smart Hub is correctly

installed and registered.

Open the WundaSmart application

and log in to your Smart Hub, select the

Devices from main menu and choose

Smart Connection Box.

Registering the device

You have 30 seconds to pair the Smart

Connecton Box. Press and hold button 

and wait for the LED light to turn green.

The installed Smart Connection Box will

appear on the device list.

Congure heating zones (rooms) in your

applicaction.

12× zone valve

3D valve

heating source

pump

temp.

sensor

1 2

~















Inhaltsverzeichnis

Andere Wunda Hausautomation Handbücher

Wunda

Wunda WundaSmart Radiator Head Bedienungsanleitung

Beliebte Hausautomation Handbücher anderer Marken

Truth Hardware

Truth Hardware Sentry II Bedienungsanleitung

FIBARO

FIBARO FGWPA-111 Bedienungsanleitung

Hezborg

Hezborg BGR8016B Bedienungsanleitung

MYDLINK

MYDLINK Pro Series Bedienungsanleitung

Panasonic

Panasonic KX-HNA101FX Bedienungsanleitung

GamaBit

GamaBit Houseper Bedienungsanleitung

nedis

nedis WIFILRF10C37 Bedienungsanleitung

Veho

Veho TA45 Bedienungsanleitung

Nexa

Nexa ZPR-111 Bedienungsanleitung

Vimar

Vimar 00801 Bedienungsanleitung

Leviton

Leviton 47604-F6 Bedienungsanleitung

EVERSPRING

EVERSPRING AN180 Bedienungsanleitung

Coltech

Coltech 18-1339 Bedienungsanleitung

IDS

IDS NXT vegas Leitfaden

Vimar

Vimar 03975 Bedienungsanleitung

iNels

iNels RFIM-20B Bedienungsanleitung

EVA Logik

EVA Logik ZW30 Bedienungsanleitung

Leviton

Leviton ODCØP-S0W Bedienungsanleitung