Wybron Eclipse Bedienungsanleitung

Troubleshooting Information

Wybron Eclipse I Dowser

PC Board Level

TROUBLESHOOTING

1. Symptom: The vanes do not have full travel and the unit is “shutting down”

(all 4 LEDs are flashing in unison).

a. Problem: The vanes are hitting screws protruding into the unit.

Remedy: First, double check the installation of the mounting

and barndoor tabs on the front and back covers. The screws

should come flush with the back of the cover, not protruding

into the dowser "vane area" by more than 1/16", else

interference with the vanes will cause shutdowns. The screws

supplied should have been 8/32 x 1/4" panheads for model

17000, and 1/2" for models 11010 and 9001.

b. Problem: The linkage set screws have loosened.

Remedy: Tighten them per the following procedure:

1. Remove both the front and back covers from the dowser.

2. Set the dowser to "local control" and connect to the powersupply.

3. Use the local control buttons to fully close the vanes. If the dowser

doesn't respond, remove power and manually close the vanes.

4. Looking at the unit with the local control buttons facing you, the

second vane from the left hand side connects to a coupler which

connects the vane to the motor. Make sure the coupler set screw is

tight. Use a 0.050” or 1.3mm or 1/16" Allen wrench.

5. Beneath the coupler, is the gear that drives the other set of vanes.

Loosen both set screws on this gear. Gently press across the

vanes to ensure they are evenly closed, and retighten the set

screws.

c. Problem: The vanes are bowed.

Remedy: With the vanes fully open, look along them for any bowing where

they might have been bent. This will also show up as the edges of the

vanes clashing instead of meshing when closing. Minor bends can be

straightened with gentle pressure in reverse direction.

2. Symptom: The unit is “shutting down” (all 4 LEDs are flashing in unison)

for an unknown reason.

a. Problem: It is drawing excessive current (typical current is about 0.4 amps

when initializing or opening or closing quickly)

Remedy: The unit may have been dropped, causing misalignment of the

vanes axles. Remove the two screws attaching each vane to the linkage

and verify that they spin freely. Binding may indicate bent axles on the

bulkheads, or cracked brass pivots. Replace as necessary.

Remedy: Check the PC board for corrosion due to exposure and replace

the PC board if this is found.

Remedy:

If no binding or other mechanical friction exists, replace the motor.

Inhaltsverzeichnis

Andere Wybron DJ-Equipment Handbücher

Wybron

Wybron CYGNUS VN100 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung